Star Micronics SP500 Series Bedienungsanleitung

DOT MATRIX PRINTER

SP500 SERIES

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the

Electro Magnetic Compatibility Directive of the European Communities as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950, following the provisions of the Low Voltage Directive of the

European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

SP500 Series: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

TABLE OF CONTENTS

1. Outline ...............................................................................................................1

2. Unpacking and Installation ................................................................................2

2-1. Unpacking ..............................................................................................2

2-2. Locating the Printer ...............................................................................3

2-3. Handling Care ........................................................................................ 3

2-4. Maintenance ...........................................................................................3

3. Parts Identification and Nomenclature ..............................................................4

4. Connecting Cables and Power Cord ..................................................................6

4-1. Connecting the Interface Cable .............................................................. 6

4-2. Connecting to a Peripheral Unit ............................................................. 7

4-3. Connecting the Power Cord ...................................................................8

4-4. Turning Power On .................................................................................9

4-5. Attaching the Rear Cover.......................................................................9

4-6. Installing the cable ...............................................................................10

4-7. Switch Blind Installation .....................................................................11

5. Loading the Ribbon Cartridge and Paper ........................................................12

5-1. Tear Bar Model ....................................................................................12

5-2. Auto Cutter Model ...............................................................................15

5-3. Installing the Roll Paper Guide ............................................................18

6. Control Panel and Other Functions .................................................................19

6-1. Control Panel .......................................................................................19

6-2. Basic Indicators .................................................................................... 19

6-3. Errors ...................................................................................................20

6-4. Adjustment Mode ................................................................................22

Appendix A: General Specifications .................................................................104

Power Supply Specifications ......................................................................106

Appendix B: Serial Interface .............................................................................107

B-1. Pins and Signal Names ......................................................................107

B-2. Interface Connections ........................................................................108

Appendix C: Parallel Interface ..........................................................................109

C-1. Table of Connection Signals for Each Mode ..................................... 109

D-1. Parallel Interface ................................................................................111

Appendix D: DIP Switch Setting ......................................................................111

D-2. Serial Interface ...................................................................................112

Appendix E: Memory Switch Settings ..............................................................114

Appendix F: Peripheral Unit Driver Circuit .....................................................115

Appendix G: Adjusting the Dot Alignment Mode ...........................................117

Appendix H: Black Mark Sensor Alignment Mode .........................................119

– 1 –

ENGLISH

The SP500 Series Serial Impact Dot Matrix Printer is designed for use with

electronic instruments such as POS, banking equipment, computer peripheral

equipment, etc.

The major features of the SP500 series are as follows:

1. Bi-directional printing at approx. 4 lines/sec.

2. Serial interface or parallel interface.

3. The data buffer allows the unit to receive print data even during printing.

4. Peripheral unit drive circuit enables control of external devices such as cash

drawers.

SP5 1 2 M D 42

No. of print columns

42 : 42 columns (16.9 CPI)

Interface

D : Serial interface (RS-232C)

C : Parallel interface

Paper feed

M : Friction paper feed method

Mechanism

2 : Single color, 42 columns (16.9 CPI)

Printer type

1 : Tear bar type

4 : Auto cutter equipped type

SP500 series printer

1. Outline

–2 –

ENGLISH

2-1. Unpacking

After unpacking the unit, check that all the necessary accessories are included in

the package.

Tear bar model Auto cutter model

Fig. 2-1 Unpacking

If anything is missing, contact the dealer where you bought the printer and ask

them to supply the missing part. Note that it is a good idea to keep the original box

and all the packing materials just in case you need to pack the printer up again and

send it somewhere at a later date.

OFF

ERROR

POWER

FEED

2. Unpacking and Installation

Printer Printer

Rear cover Switch blind

Power cordRoll paper guide

OFF

ERROR

POWER

FEED

Ribbon cartridge

User’s manual

–3 –

ENGLISH

2-2. Locating the Printer

When you locate your printer, keep the following tips in mind:

1. Protect your printer from excessive heat such as direct sunlight or heaters, and

keep it away from moisture and dust.

2. Place the printer on a firm, level surface which is fairly vibration-free.

3. A steady power supply that is not subject to power surges should be connected

to the printer.

For example, do not connect it to the same circuit as a large, noise-producing

appliance such as a refrigerator or an air conditioner.

4. Make sure the line voltage is the voltage specified on the printer’s identifica-

tion plate.

5. To disconnect the printer, the plug has to be disconnected from the wall socket,

which has to be located close to the printer, and easy to access.

2-3. Handling Care

1. Be careful not to drop paper clips, pins or other foreign matter into the unit as

these cause the printer to malfunction.

2. Do not attempt to print when either paper or ribbon cartridge is not located in

the printer, otherwise the print head can be damaged.

3. Do not open the cover while printing.

4. Do not touch the print head immediately after printing as it gets very hot.

5. Use only roll paper that is not glued to the core.

6. When the paper end mark appears on the paper, replace the roll paper before

it runs out.

2-4. Maintenance

Essentially, your printer is a robust piece of equipment, but should be treated with

a modicum of care in order to avoid malfunctions. For example:

1. Keep your printer in a “comfortable”environment. Roughly speaking, if you

feel comfortable, then the environment is suitable for your printer.

2. Do not subject the printer to physical shocks or excessive vibration.

3. Avoid over-dusty environments. Dust is the enemy of all precision mechani-

cal devices.

4. To clean the exterior of the printer, use a cloth barely dampened with either

water with a little detergent or a little alcohol, but do not allow any liquid to

fall inside the printer.

5. The interior of the printer may be cleaned with a small cleaner or a com-

pressed-air aerosol (sold for this purpose). When performing this operation,

be sure not to bend or damage any cable connections or electronic compo-

nents.

–4 –

ENGLISH

OFF

ERROR

POWER

FEED

3. Parts Identification and Nomenclature

Tear bar model

Fig. 3-1 External view of the printer (Tear bar model)

Cover

Protects the printer from dust and reduces noise.

Do not open the cover while printing.

Control panel

Features one control switch and

two indicators to indicate printer

status.

Interface connector

Connects the printer with

host computer.

Power switch

Turns printer power on

and off.

Peripheral unit drive circuit

connector

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to a

telephone.

Power connector

For connection of

the power cord.

–5 –

ENGLISH

OFF

ERROR

POWER

FEED

Auto cutter model

Fig. 3-2 External view of the printer (Auto cutter model)

Cover

Protects the printer from dust and reduces noise.

Do not open the cover while printing.

Control panel

Features one control switch and

two indicators to indicate printer

status.

Interface connector

Connects the printer with

host computer.

Peripheral unit drive circuit

connector

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to a

telephone.

Power switch

Turns printer power on

and off.

Power connector

For connection of

the power cord.

–6 –

ENGLISH

OFF

4. Connecting Cables and Power Cord

4-1. Connecting the Interface Cable

Note: Before connecting/disconnecting the interface cable, make sure that

power to the printer and all the devices connected to the printer is

turned off.

Also make sure the power cable plug is disconnected from the

AC outlet.

(1) Connect the interface cable to the connector on the rear panel of the printer.

(2) In the case of a serial interface, tighten the connector screws. In the case of a

parallel interface, fasten the connector clasps.

Serial interface cable

Parallel interface cable

–7 –

ENGLISH

4-2. Connecting to a Peripheral Unit

You can connect a peripheral unit to the printer using a modular plug. The

following describes how to install the ferrite core and make the actual connection.

See “Modular plug”on page 115 for details about the type of modular plug that

is required. Note that this printer does not come with a modular plug or wire, so

it is up to you to obtain one that suits your needs.

Important!

Make sure that the printer is turned off and unplugged from the AC outlet

and that the computer is turned off before making connections.

(1) Connect the peripheral drive cable to the connector on the rear panel of the

printer.

Important!

Do not connect a telephone line into the peripheral drive connector.

Failure to observe this may result in damage to the printer.

Also, for safety purposes, do not connect wiring to the external drive

connector if there is a chance it may carry peripheral voltage.

OFF

Andere Handbücher für SP500 Series

Inhaltsverzeichnis

Sprachen:

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics SB-10 Bedienungsanleitung

Star Micronics

Star Micronics TCP300II Series Montageanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungsanleitung

Star Micronics

Star Micronics SP312F Bedienungsanleitung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-8521 Bedienungsanleitung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-1011C Bedienungsanleitung

Star Micronics

Star Micronics Multi-Font NX-2410 Bedienungsanleitung

Star Micronics

Star Micronics TSP650II SERIES Bedienungsanleitung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics SP317 Bedienungsanleitung

Star Micronics

Star Micronics LC-8211 Bedienungsanleitung

Star Micronics

Star Micronics DP8340RC Series Bedienungsanleitung

Star Micronics

Star Micronics SM-S200 Series Montageanleitung

Star Micronics

Star Micronics TSP200 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-240C Bedienungsanleitung

Star Micronics

Star Micronics LC24-15 Bedienungsanleitung

Star Micronics

Star Micronics gemini-10X Bedienungsanleitung

Star Micronics

Star Micronics SJ-144MC Bedienungsanleitung

Star Micronics

Star Micronics LC24-20 Bedienungsanleitung

Star Micronics

Star Micronics LC24-300 COLOUR Bedienungsanleitung

Star Micronics

Star Micronics NB24-10/15 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung