Star Micronics Star DP8340 Bedienungsanleitung
DOT MATRIX PRINTER
DP8340 SERIES
[SERIAL INTERFACE]
USERS MANUAL
Federal Communications Commission
Radio Frequency Interference
Statement
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,
pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
against harmful interference when the equipment is operated in a commercial environment.
Thisequipment generates,uses andcan radiateradio frequencyenergy and,if notinstalled and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interferenceinwhichcasetheuserwillberequiredtocorecttheinterferenceathisownexpense.
For compliance with the Federal Noise Interference Standard, this equipment requires a
shielded cable.
This statement will be applied only for the printers marketed in U.S.A.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
Thisdigital apparatus doesnot exceed theClass A limitsfor radio noiseemissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectiques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
The above statement applies only to printers marketed in Canada.
CE
Manufacturer’s Declaration of Conformity
EC Council Directive 89/336/EEC of 3 May 1989
Thisproduct, has beendesigned and manufacturedin accordance withthe International StandardsEN 50081-1/01.92 and
EN 50082-1/01.92, following the provisions of the Electro Magnetic Compatibility Directive of the European Commu-
nities as of May 1989.
EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993
This product, has been designed and manufactured in accordance with the International Standards EN 60950, following
the provisions of the Low Voltage Directive of the European Communities as of July 1993.
The above statement applies only to printers marketed in EU.
Trademark acknowledgments
DP8340: Star Micronics Co. Ltd.
Notice
• All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express
permission, is strictly forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the time of printing. However,
should any errors be found, STAR would greatly appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 1986, 1999 Star Micronics Co., Ltd.
TABLE OF CONTENTS
1. OUTLINE..............................................................................................1
2. UNPACKING AND INSTALLATION................................................2
2-1. Unpacking ....................................................................................2
2-2. Installation of Paper Holders and Re-Roll Prevention Guard
(Only Model DP8340F) ...............................................................3
2-3. Handling Notes.............................................................................4
3. PART IDENTIFICATION AND NOMENCLATURE ........................5
3-1. Power Supply Unit .......................................................................5
3-2. Printer...........................................................................................6
3-3. Part Functional Description..........................................................7
4. INSTALLATION OF INK RIBBON AND PAPER.............................8
4-1. Installation of Ink Ribbon ............................................................8
4-2. Removal of Ink Ribbon................................................................9
4-3. Paper Insertion ...........................................................................10
4-3-1. Model DP8340F ..............................................................10
4-3-2. Model DP8340S ..............................................................11
4-4. Paper Removal ...........................................................................12
5. CONTROL CODES ............................................................................13
6. GENERAL SPECIFICATIONS..........................................................19
7. INTERFACE FOR MODEL DP8340-M
(MODULAR JACK CONNECTOR)..................................................22
7-1. Interface Specifications ..............................................................22
7-2. Interface Circuit .........................................................................22
7-3. Setting of the DIP Switches .......................................................23
7-3-1. DIP-SW 1 ........................................................................23
7-3-2. DIP-SW2 .........................................................................23
7-4. Connectors and Signals ..............................................................24
7-5. Interface Connections.................................................................25
7-6. Peripheral Unit Drive Circuit .....................................................26
7-6-1. Cable Connection ............................................................26
7-6-2. Peripheral Drive Circuit ..................................................27
7-6-3. Control Codes..................................................................27
8. INTERFACE FOR MODEL DP8340-D
(D-SUB 25 PIN CONNECTOR).........................................................28
8-1. Interface Specifications..............................................................28
8-2. Interface Circuit .........................................................................29
8-2-1. RS-232C ..........................................................................29
8-2-2. Current Loop ...................................................................29
8-3. Setting of the DIP Switches .......................................................30
8-3-1. DIP-SW 1 ........................................................................30
8-3-2. DIP-SW 2 ........................................................................30
8-4. Jumper Setting............................................................................31
8-4-1. Removal of the Bottom Cover ........................................31
8-4-2. Setting of Jumper ............................................................31
8-5. Connectors and Signals ..............................................................32
8-6. Interface Connections.................................................................33
8-7. Peripheral Unit Drive Circuit .....................................................34
8-7-1. Cable Connection ............................................................34
8-7-2. Peripheral Drive Circuit ..................................................35
8-7-3. Control Codes..................................................................35
9. DATA STRUCTURE AND CONTROL ............................................36
9-1. DTR Mode (1 BLOCK) .............................................................36
9-2. X-ON/X-OFF Mode...................................................................37
9-3. STX-ETX Mode.........................................................................39
10. CHARACTER CODE LIST..............................................................41
11. FONT LIST .......................................................................................44
12. WHEN POWER IS SUPPLIED BY THE USER .............................48
13. FERRITE CORE INSTALLATION (EU ONLY) ............................50
– 1 –
1.OUTLINE
TheDP8340seriesofserialdotmatrixprintersisforuseinECR,POS,electronic
instruments, banking machines and computer peripheral equipment.
The DP8340 series include the following features;
1) 2 color printing (Red and Black)
2) High-speed bidirectional printing (2 line/sec, 40 columns per line)
3) 9-pin print head
4) The interface conforms to RS-232C in M type, and to RS-232C/20mA
Current Loop in D type.
5) Commandsforexpandedcharacters,invertedcharacters,emphasizedchar-
acters, and red and black printing are provided, which makes the printer
very versatile.
6) Simultaneous Data Communication and Printing
7) Error Checking Protocol
8) Peripheral Driver
9) Reverse Channel providing status and full control
Model Name Notation
– 2 –
2.UNPACKINGANDINSTALLATION
2-1. Unpacking
After opening the box, check if all necessary accessories are included.
(A) Printer
(B) Power Supply Unit
Figure 2-1. Unpacking
1Printer
2User’s Manual
3Paper Holders
4Re-Roll Prevention Guard
5Ink Ribbon
6DIP Switch Cover
7Ferrite Core (EU only)
1
1Power Supply Unit
2User’s Manual
– 3 –
2-2. Installation of Paper Holders and Re-Roll Prevention
Guard (Only Model DP8340F)
Install the Paper Holders in the outermost holes in the rear of the printer.
Figure 2-2. Installation of Paper Holders
– 4 –
InstalltheRe-Roll PreventionWirein theholesoftheprinter cover.Twistingthe
Wire as shown in the figure below, will make the installation easier.
Figure 2-3. Installation of Re-Roll Prevention
2-3. Handling Notes
(1) Install the printer near an easily accessible socket-outlet.
(2) Place the unit on a flat and stable surface for operation.
(3) Do not connect the AC Power Plug to the same outlet used for other noise
generating devices (large motors, etc.).
(4) Be careful not to drop paper clips, pins and other foreign objects into the
unit.
(5) Wipe off dirt with a soft cloth soaked in alcohol or benzine. Do not use
Lacquer thinner, Trichlorethelene or Ketone solvents because they may
damage plastic parts.
(6) Use a soft brush, etc. for cleaning the printer mechanism and PCB.
(7) Keep hands out of printer while power is on.
(8) Do not attempt to print when there is no ink ribbon or paper in the unit. The
print head life could be severly reduced.
(9) Ifthepaper is fastened tightly to the roll, the paper may notdetachfromthe
roll when the end is reached.
If this happens, the no paper detection function and paper feed will not
operate.
(10) Always keep the printer cover attached when printing to prevent paper
jams, noise, and other problems.
(11) Always turn the power off before opening the printer cover. (e.g. When
renewing a ink ribbon)
– 5 –
3.PARTIDENTIFICATIONANDNOMENCLATURE
3-1. Power Supply Unit
Figure 3-1. Power Supply Unit
DC Power Connector (Output)
Shape of AC Power plug will
vary according to destinations.
– 6 –
3-2. Printer
Figure 3-2. Printer: Front View
Figure 3-3. Printer: Rear View
Andere Handbücher für Star DP8340
2
Dieses Handbuch passt für folgende Modelle
21
Inhaltsverzeichnis
Andere Star Micronics Drucker Handbücher
Star Micronics
Star Micronics TSP700 Series Bedienungsanleitung
Star Micronics
Star Micronics DP8340RC Series Bedienungsanleitung
Star Micronics
Star Micronics MP100 Handbuch
Star Micronics
Star Micronics TSP600 Series Bedienungs- und Wartungshandbuch
Star Micronics
Star Micronics SP500 Series Bedienungsanleitung
Star Micronics
Star Micronics TSP700 Series Bedienungs- und Wartungshandbuch
Star Micronics
Star Micronics TSP100LAN Bedienungsanleitung
Star Micronics
Star Micronics PW2000-24 Bedienungsanleitung
Star Micronics
Star Micronics USB Bedienungsanleitung
Star Micronics
Star Micronics TUP900 Series Bedienungsanleitung
Star Micronics
Star Micronics Line Thermal Printer Bedienungsanleitung
Star Micronics
Star Micronics LC-20 Bedienungsanleitung
Star Micronics
Star Micronics Star SCP700 Series Bedienungs- und Wartungshandbuch
Star Micronics
Star Micronics TSP100LAN Bedienungsanleitung
Star Micronics
Star Micronics TSP600 Series Bedienungsanleitung
Star Micronics
Star Micronics LC-100+ Bedienungsanleitung
Star Micronics
Star Micronics XB24-200 Bedienungsanleitung
Star Micronics
Star Micronics Delta Bedienungsanleitung
Star Micronics
Star Micronics TSP800 Series Bedienungsanleitung
Star Micronics
Star Micronics LaserPrinter 8 Bedienungsanleitung
