START International LD2000 Bedienungsanleitung

02/03

TM

instructions

LD

2000

TM

START International

4270 Airborn Dr.

Addison, TX 75001, USA

Tel 972.248.1999

Fax 972.248.1991

[email protected]

www.startinternational.com

START Japan Corporation

1-26-14 Toshin-Cho

Itabashi-ku

Tokyo, Japan

Tel 81.3.3554.5608

Fax 81.3.5966.9591

[email protected]

5

4

Place the label roll onto the reel hanger bar. The roll should be against a metal lock clip

so that it is held straight. Place second metal lock clip onto reel hanger bar to keep the

labels snug.

Thread the web under the guide rod, between the hold down and the strip plate and

back under the strip plate. Lay the web across the slot in the take-up hub. Lock the web

in position with the metal lock rod. (The take-up hub turns counter-clockwise.)

Hold Down:

Using the upper thumbscrew on the side of the machine, adjust the hold down for

tensioning. For best results, labels should be pressed firmly against the strip plate.

However, if the labels are held too tightly, they will cause excessive drag on the motor.

Photosensor:

The photosensor can be adjusted in any direction by using the lower thumbscrew on the

side of the machine and the thumbscrew underneath the photosensor bracket. Loosening

the thumbscrew on the side of the machine allows the photosensor to move in and out.

This is used to set the overhang distance of the label over the strip plate. The

thumbscrew underneath the photosensor bracket is used to swivel the sensor along the

front of the strip plate. When the label is being fed the correct distance, lock the bracket

in place. If there are 2 or more labels across, align the photosensor with the last label to

be removed. When these screws are locked in place, the machine is set.

Hold Down

Photosensor

Strip Plate

Guide Rod

Lock Rod

Take-up Hub

Reel Hanger Bar

Reel Holder Arm

Incorrect

Correct

Sensor sees beyond label

- Will not stop Sensor sees strip plate

- Will not feed

Sensor sees front edge of label

ADJUSTMENTS

SET-UP INSTRUCTIONS

Positioning of Photosensor

Daisy-chain option:

LD2000 dispensers can be “daisy-chained” together to operate in series. When a label

is removed from one of the machines, the next label will not feed until the labels are

removed from all the machines. Example: If 3 machines are “daisy-chained” together,

when a label is taken off the first machine, it will not feed; when a label is taken off the

second machine, it will not feed. When the label is taken from the third machine, all

machines will feed their respective labels. (LD2000-CABLE needed to “daisy-chain”

machines.)

5

4

Place the label roll onto the reel hanger bar. The roll should be against a metal lock clip

so that it is held straight. Place second metal lock clip onto reel hanger bar to keep the

labels snug.

Thread the web under the guide rod, between the hold down and the strip plate and

back under the strip plate. Lay the web across the slot in the take-up hub. Lock the web

in position with the metal lock rod. (The take-up hub turns counter-clockwise.)

Hold Down:

Using the upper thumbscrew on the side of the machine, adjust the hold down for

tensioning. For best results, labels should be pressed firmly against the strip plate.

However, if the labels are held too tightly, they will cause excessive drag on the motor.

Photosensor:

The photosensor can be adjusted in any direction by using the lower thumbscrew on the

side of the machine and the thumbscrew underneath the photosensor bracket. Loosening

the thumbscrew on the side of the machine allows the photosensor to move in and out.

This is used to set the overhang distance of the label over the strip plate. The

thumbscrew underneath the photosensor bracket is used to swivel the sensor along the

front of the strip plate. When the label is being fed the correct distance, lock the bracket

in place. If there are 2 or more labels across, align the photosensor with the last label to

be removed. When these screws are locked in place, the machine is set.

Hold Down

Photosensor

Strip Plate

Guide Rod

Lock Rod

Take-up Hub

Reel Hanger Bar

Reel Holder Arm

Incorrect

Correct

Sensor sees beyond label

- Will not stop Sensor sees strip plate

- Will not feed

Sensor sees front edge of label

ADJUSTMENTS

SET-UP INSTRUCTIONS

Positioning of Photosensor

Daisy-chain option:

LD2000 dispensers can be “daisy-chained” together to operate in series. When a label

is removed from one of the machines, the next label will not feed until the labels are

removed from all the machines. Example: If 3 machines are “daisy-chained” together,

when a label is taken off the first machine, it will not feed; when a label is taken off the

second machine, it will not feed. When the label is taken from the third machine, all

machines will feed their respective labels. (LD2000-CABLE needed to “daisy-chain”

machines.)

02/03

TM

instructions

LD

2000

TM

START International

4270 Airborn Dr.

Addison, TX 75001, USA

Tel 972.248.1999

Fax 972.248.1991

[email protected]

www.startinternational.com

START Japan Corporation

1-26-14 Toshin-Cho

Itabashi-ku

Tokyo, Japan

Tel 81.3.3554.5608

Fax 81.3.5966.9591

[email protected]

Inhaltsverzeichnis

Andere START International Spender Handbücher

START International

START International THE LABEL DISPENSER LD2000 Bedienungsanleitung

START International

START International LDX8000 Series Bedienungsanleitung

START International

START International ZCM1000 Series Bedienungsanleitung

START International

START International TDH2O5 Bedienungsanleitung

START International

START International TDA025 Bedienungsanleitung

START International

START International THO DC5100 Bedienungsanleitung

START International

START International Tape TDH2O5 Bedienungsanleitung

START International

START International Label LD7500 Bedienungsanleitung

START International

START International Tape TDH2O1 Bedienungsanleitung

START International

START International Label LD5000 Bedienungsanleitung

START International

START International Tape TDA150 Bedienungsanleitung

START International

START International LD8025 Bedienungsanleitung

START International

START International TAPE DISPENSER TDA150 Bedienungsanleitung

START International

START International LD3500 Bedienungsanleitung

START International

START International LR4500 Bedienungsanleitung

START International

START International LD3000 Bedienungsanleitung

START International

START International Tape TDA080-NM Bedienungsanleitung

START International

START International LD6000 Series Bedienungsanleitung

START International

START International Labelmoto LD6025 Bedienungsanleitung

START International

START International LD3000 FDA Bedienungsanleitung

START International

START International Label LD2000 Bedienungsanleitung

START International

START International TDH2O1 Bedienungsanleitung

Beliebte Spender Handbücher anderer Marken

Silver King

Silver King Majestic SK12MAJ Kurzanleitung

Franke

Franke F3Dn Twin Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Bedienungsanleitung

DAN DRYER

DAN DRYER 282 Bedienungsanleitung

Essity

Essity Tork 473208 Bedienungsanleitung

CBS

CBS SD300BU-88 Einrichtungshandbuch

Sealey

Sealey MK77 Bedienungsanleitung

Fluid Management

Fluid Management Accutinter 1600 Bedienungsanleitung

Franke

Franke DVS SD99-010 Bedienungsanleitung

Graco

Graco Dispensit 1053-10C Fehlerbehebungshandbuch

ITALTINTO

ITALTINTO i50 Bedienungsanleitung

Coca-Cola

Coca-Cola FREESTYLE 9000 Bedienungsanleitung

Graco

Graco ProMix 2KE Bedienungsanleitung

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Bedienungsanleitung

Wayne

Wayne GLOBAL VISTA CNG Bedienungsanleitung

clarsen

clarsen H133 Bedienungsanleitung

PicoBrew

PicoBrew Zymatic Bedienungsanleitung

BOWMAN

BOWMAN BP-007 Bedienungsanleitung