StarTech.com IPUSB2HDMI Bedienungsanleitung

HDMI Video Adapter

Ethernet or USB to HDMI Video

Adapter

IPUSB2HDMI

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver•

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company

in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction..................................................................... 1

Packaging Contents.....................................................................1

System Requirements .................................................................1

Side 1 View..................................................................................2

Side 2 View..................................................................................2

Installation Diagram........................................................ 3

Installation....................................................................... 4

Software Installation for Windows 2000/XP/Vista/7.....................4

Hardware Installation for USB .....................................................5

Hardware Installation for Ethernet ...............................................6

Installation for Mac OS X............................................................8

Conﬁguration .................................................................. 9

Windows 2000/XP/Vista/7 ...........................................................9

Mac OS X ....................................................................................12

Speciﬁcations.................................................................. 15

Technical Support........................................................... 16

Warranty Information...................................................... 16

Introduction

The StarTech.com IPUSB2HDMI Video Adapter offers versatile

performance by providing either a USB-to-HDMI connection or an IP/

Ethernet-to-HDMI connection between a PC and HDMI-capable display

device. The ideal solution for PCs lacking a digital video output or PCs

that require an additional display at long distances/remote locations.

Packaging Contents

1 x IPUSB2HDMI video adapter•

1 x USB cable•

1 x Universal Power Adapter•

1 x Driver Installation CD•

1 x Instruction Manual•

System Requirements

HDMI enabled display device•

Minimum CPU: Intel/AMD 2.4 GHz single core•

Minimum RAM: 1GB•

Microsoft Windows• ®2000/XP/Vista/7 (32/64-bit)*

*64-bit only supported over direct USB connection

Apple Mac OS• ®10.4.11 or later (USB operation only)

Power

LED

Link

LED

HDMI connector

(output)

DC Power

connector

EDID Pass-thru

Switch

USB Hub

connectors RJ45 connector

USB mini-B

connector (host)

Host Connection

Switch

Reset Switch

Side 1 View

Side 2 View

Installation Diagram

*optional USB accessories

*only one interface can be

used at a time

Installation

Please note: The following installation steps must be completed prior

to connecting USB adapter to the host computer, to ensure proper

functionality.

Software Installation for Windows 2000/XP/Vista/7

Insert the Driver CD (included) into the CD/DVD-ROM drive.1.

Browse through the Driver CD and locate the “Setup.exe” ﬁle under2.

the “USB to HDMI Software” folder. Double-click on the “Setup.exe”

ﬁle to begin the installation process:

When the End User License3.

Agreement appears, please

read and accept it, then click

Next.

Please wait while the installation package copies the necessary ﬁles.4.

Once completed, in the main (root) directory of the CD, run the5.

XP_VS_Setup.exe ﬁle top being the driver installation.

When the end of the installation is reached, click “Finish” to restart6.

the computer system.

After Windows has fully loaded, the Video Adapter will be ready to7.

use.

Hardware Installation for USB

Set the EDID slide switch to the ON position.1.

Plug the power adapter into the HDMI Video Adapter. The Power2.

LED will light up steady.

Slide the “Input” selection switch to USB.3.

Plug in the USB Video Adapter adapter to the computer. Windows4.

should start to automatically load the drivers. Once complete, you

should see this icon in your System Tray:

To verify the installation, right-click on “My5.

Computer” and select Manage to open the

Computer Management window.

In the left pane of the Computer Management window, click on6.

Device Manager.

In the right pane of the Computer Management window, click on7.

Universal Serial Bus Controllers, and ensure that the USB Video

Adapter is listed underneath. Under the Sound category, will be a

CMedia USB Audio device.

Additional (up to 4) HDMI Video Adapters can now be connected to8.

the computer system. Each device will add additonal entries to the

Device Manager. Note that only one audio device can be used by

Windows at a time. So audio will only be output to one of the HDMI

Video Adapters.

OPTIONAL: Connect any USB peripherals to be shared along with

the HDMI Video Adapter, into the available USB hub ports on the unit.

They will appear as directly connected to the computer system.

Hardware Installation for Ethernet

Set the EDID slide switch to the ON position.1.

Connect the power adapter to the HDMI Video Adapter. The Power2.

LED will light up steady.

Slide the “Input” selection switch to Ethernet.3.

Connect the RJ45 connector on the HDMI Video Adapter to an4.

available Ethernet port on the network equipment, or directly to the

computer system.

If a DHCP server is available, the HDMI Video Adapter will5.

automatically obtain an IP address and network settings to be able

to communicate with other devices on the network.

If a DHCP server is not available, such as connecting directly to a

computer system, the computer system must be set to use an IP

address of 169.254.10.1 to be able to communicate with the HDMI

Video Adapter.

Launch the USB Server software6.

from the desktop Icon.

The USB Server software will list7.

the HDMI Video Adapter, with it’s

currently assigned IP address.

Under it will be listed all

components of the HDMI Video

Adapter that can be accessed by

the computer system (i.e. video

and audio components).

Double-click on the component that needs to be connected, or8.

highlight the component and click the “Connect” button. The Icon will

change colour from green to orange.

The connected component will then be detected by the computer9.

system and be accessible as if directly connected.

To disconnect the component, double-click on it again, or highlight10.

it and click the “Disconnect” button.

OPTIONAL: Connect any USB peripherals to be shared along with

the HDMI Video Adapter, into the available USB hub ports on the unit.

They will appear as additional connectable components in the USB

Server software.

Inhaltsverzeichnis

Andere StarTech.com Adapter Handbücher

StarTech.com

StarTech.com USB32HDDVII Bedienungsanleitung

StarTech.com

StarTech.com MDP2VGDVHD Bedienungsanleitung

StarTech.com

StarTech.com U2M2E125 Bedienungsanleitung

StarTech.com

StarTech.com ICUSB2321F Bedienungsanleitung

StarTech.com

StarTech.com US2GA30 Bedienungsanleitung

StarTech.com

StarTech.com PEXESAT32 Bedienungsanleitung

StarTech.com

StarTech.com TB32DP2 Bedienungsanleitung

StarTech.com

StarTech.com ICUSB232 Bedienungsanleitung

StarTech.com

StarTech.com USB32DPPRO Systemhandbuch

StarTech.com

StarTech.com USB3S2SATA Bedienungsanleitung

StarTech.com

StarTech.com 103B-USBC-MULTIPORT Bedienungsanleitung

StarTech.com

StarTech.com MDP2HDMIUSBA Bedienungsanleitung

StarTech.com

StarTech.com ST2000PEXPSE Bedienungsanleitung

StarTech.com

StarTech.com USBA-BLUETOOTH-V5-C2 Bedienungsanleitung

StarTech.com

StarTech.com RJ45SPLITTER Bedienungsanleitung

StarTech.com

StarTech.com US100A20SFP Bedienungsanleitung

StarTech.com

StarTech.com PEX2S552B Bedienungsanleitung

StarTech.com

StarTech.com DK30C2HAGPD Bedienungsanleitung

StarTech.com

StarTech.com ICUSB2328 Bedienungsanleitung

StarTech.com

StarTech.com CF2X2IDE25 Bedienungsanleitung

StarTech.com

StarTech.com USB32HD2 Bedienungsanleitung

StarTech.com

StarTech.com USB2105S Bedienungsanleitung

StarTech.com

StarTech.com USB2VGAE Bedienungsanleitung

StarTech.com

StarTech.com US100A20FXSC Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung