StarTech.com SV565UTP Bedienungsanleitung

PS/2 & USB KVM Console Extender

SV565UTP Instruction Manual

Actual product may vary from photo

UTP KVM Signal Extender for Distances up to 500 feet (150 m)

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other

Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Connecting Your KVM Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Preparing Your Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installing the Host Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installing the Remote Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Using Your KVM Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Using the Host Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Using the Remote Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Accessory Products from StarTech.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Instruction Manual

Introduction

Thank you for purchasing a StarTech.com KVM extender. This product allows a

computer to control a host system from a remote location at a distance of up to 500 feet

(150 meters). For ease of installation, this product uses standard Category 5, 5E, or 6

network cabling that fits easily into almost any existing network infrastructure. For added

versatility, the KVM extender supports either PS/2 or USB computer interfaces. Console

support is provided using standard PS/2 and VGA connectors.

Features

•Control a USB or PS/2-based computer at a distance of up to 500 feet (150 meters)

•Continue to use the computers at the host or remote locations when a remote KVM

session isn’t active using the dedicated PS/2 console interface

•Uses standard UTP network cabling for easy installation

Before You Begin

System Requirements

•1integrated KVM cable each for the host and remote computers (not provided)

StarTech.com part number: SVECONx (PS/2)

SVECONUSx (USB)

• Unshielded Category 5 twisted pair (UTP) straight-through network cable

terminated at each end with RJ-45 connectors (if using surface cabling)

• Unshielded Category 5 twisted pair (UTP) straight-through network cable

terminated at each end in a wall-mounted outlet, with a standard Category 5 patch

cable, at both locations (if using premises cabling)

NOTE: The total length of cable between the Host and Remote Units cannot exceed 500

feet (150 meters), including patch cables (if used). Category 5e and 6 cabling is

compatible with this product and may improve performance.

NOTE: Long cable lengths between the Host and Remote Units may adversely affect

image quality at high resolutions and refresh rates. If you need to run your remote

displays at high resolutions and frequencies, use as little cabling between locations as

possible and avoid practices such as “coiling” unused cable in a ceiling.

This product will also control a KVM switch, allowing you to manage more than one

computer remotely. In this configuration, you can connect the KVM extender’s Host Unit

to the “console” ports on the KVM. You must use the provided power adapters if using

this configuration. You should set the Host Unit to Compatibility Mode before connecting

it to a KVM that uses the [Ctrl] key as its hotkey sequence; see page 4 for details.

Instruction Manual

Contents

This package should contain:

1 x Host Unit

1 x Remote Unit

1 x Instruction Manual

2 x Power adapter

1 x Set of rubber mounting feet

Connecting Your KVM Extender

This product is composed of two different units: the Host Unit and the Remote Unit. The

Host Unit takes input controls from a computer (using a PS/2 or USB integrated KVM

cable) and allows access to them via the Remote Unit over Category 5 UTP cable. The

remote computer also connects to the Remote Unit using an integrated KVM cable

(again, either PS/2 or USB) and allows the user at the remote site to control that

computer or the host computer using keyboard hotkey commands.

APS/2 mouse and keyboard and a VGA monitor are connected to the Remote Unit (the

console). You can also connect console peripherals to the Host Unit if you need direct

as well as remote access to that computer.

Preparing Your Site

Before you can install the the product, you need to prepare your site.

1: Determine where the host computer will be located and set up the computer.

2: Determine where the console devices (mouse, keyboard, monitor) will be located and

place them appropriately.

3a: If you are using surface cabling, ensure you have enough Category 5 unshielded

twisted pair (UTP) network cabling to connect the Host Unit to the Remote

Unit’s location, and that each end is terminated with a RJ-45 connector.

3b: If you are using premises cabling, ensure that the Category 5 unshielded twisted pair

(UTP) network cabling between the Host Unit and the Remote Unit has been

properly terminated in a wall outlet in each location and there is a

patch cable long enough to connect the Remote Unit and the Host Unit to

their respective outlets.

Installing the Host Unit

Instruction Manual

Control Indicators

UTP Cable

Host Computer Connection

(KVM cable) PS/2 + VGA Console

1: Place the Host Unit near the computer.

2: Switch off the computer and disconnect any existing VGA and input connections.

3: Using a StarTech.com integrated KVM cable (see page 8 for part numbers), connect

the end of the cable that has two (USB) or three (PS/2) connectors to the VGA Out

connector and the USB or mouse and keyboard PS/2 connectors on the computer as

appropriate. (The PS/2 version of the cable is color-coded.) Connect the opposite

end of the cable with a single connector to the gray-coded connector marked

COMPUTER on the Host Unit of the KVM extender.

4: If you wish to have console access to the host computer, connect a PS/2 mouse,

keyboard, and VGA monitor to the indicators marked as CONSOLE on the Host Unit.

5: Connect the UTP cable connection for Remote Unit to the NETWORK RJ-45

connector on the Host Unit. Connect the opposite end to a terminated wall outlet (if

you are using premises cabling).

Installing the Remote Unit

1: Place the Remote Unit near the computer.

2: Switch off the computer and disconnect any existing VGA and input connections.

3: Using a StarTech.com integrated KVM cable (see page 8 for part numbers), connect

the end of the cable that has two (USB) or three (PS/2) connectors to the VGA Out

connector and the USB or mouse and keyboard PS/2 connectors on the computer as

appropriate. (The PS/2 version of the cable is color-coded.) Connect the opposite

end of the cable with a single connector to the gray-coded connector marked

COMPUTER on the Remote Unit of the KVM extender.

4: Connect a PS/2 mouse, keyboard, and VGA monitor to the indicators marked as

CONSOLE on the Remote Unit.

5: Connect the UTP cable connection for Remote Unit to the NETWORK RJ-45

connector on the Remote Unit. Connect the opposite end to a terminated wall outlet

(if using premises cabling).

CAUTION: The UTP network cables that connect the Host and Remote Units carry

electrical current and should not be plugged in to other devices, as they may cause

damage. We strongly recommend marking the cables you are using with this product at

both locations for easy identification.

Instruction Manual

Control Indicators

UTP Cable

Remote Computer Connection

(KVM cable) PS/2 + VGA Console

Using Your KVM Extender

This section details how to use your KVM extender at both the host and remote

locations.

Using the Host Unit

The Host Unit performs two functions: it allows a user at the remote location (Computer

B) to assume control of Computer A, and it also permits the user seated at Computer A

to use the system. It has three modes that control which user may access the system at

a given time: Auto (the KVM extender looks for keyboard or mouse activity from both A

and B and automatically accepts input from the active console), Local (only the user

seated at Computer A can access the system), and Remote (only the user at Computer

B can access the system).

You can use either keyboard shortcuts (if there is a keyboard and mouse attached) or

the mode switch on the top of the Host Unit to control which user has access to

Computer A. Having a keyboard and mouse attached to the console ports on the Host

Unit is recommended since it offers access to a number of extended features.

LED Indicators

Keyboard Shortcut Command Sequences

Instruction Manual

Mode “A” Indicator “B” Indicator

Auto

(Auto senses activity) Flashing Flashing

Local

(User at Computer A has exclusive control) On (solid) Off

Remote

(User at Computer B has exclusive control) Off On (solid)

Standard Command With Compatibility Mode Enabled Description

[Ctrl] - [Ctrl] - [T] [Ctrl] - [Ctrl] - [T] Toggles control of Computer A between

Auto, Local, and Remote modes

[Ctrl] - [Ctrl] - [Esc] [Ctrl] - [Ctrl] - [Esc] Cancels the hotkey sequence

[Ctrl] - [Ctrl] - [Alt]+[E] [Ctrl] - [Ctrl] - [Alt]+[E]

Enables (2 beeps) or disables (1 beep)

Compatibility Mode so that the KVM

extender will work with a KVM switch

that also uses a [Ctrl] hotkey sequence

[Ctrl] - [Ctrl] - [1] [Ctrl] - [Ctrl] - [E] - [1]

Local Mode: Allows the user at

Computer A exclusive access to the

system; remote access from Computer

B (Remote Unit) is disabled

[Ctrl] - [Ctrl] - [2] [Ctrl] - [Ctrl] - [E] - [2]

Remote Mode: Allows the remote user

at Computer B exclusive access to

Computer A; access to the computer

from the Host Unit is disabled

[Ctrl] - [Ctrl] - [F3] [Ctrl] - [Ctrl] - [E] - [F3]

Sets the interval of inactivity in seconds

that the Host Unit will wait before

returning to Auto Mode after a Unit has

assumed control

[Ctrl] - [Ctrl] - [F4] [Ctrl] - [Ctrl] - [E] - [F4] Adjusts the typematic rate for improved

keyboard responsiveness

[Ctrl] - [Ctrl] - [F12] [Ctrl] - [Ctrl] - [E] - [F12] Resets PS/2 mouse synchronization

Beep Codes

Some of the keyboard command sequences you issue to the Host Unit have multiple

possible settings. The Unit will beep to indicate what setting you have selected for the

command you issued. (A short beep followed by a long beep indicates an invalid

command.)

[Ctrl] - [Ctrl] - [Alt]+[E] (Compatibility Mode)

1 beep: disabled

2 beeps: enabled

[Ctrl] - [Ctrl] - [F3] (Inactivity Interval for Auto Mode)

1 beep: 5 seconds

2 beeps: 15 seconds

3 beeps: 30 seconds

4 beeps: 60 seconds

[Ctrl] - [Ctrl] - [F4] (Typematic Rate)

1 beep: 6 characters/sec.

2 beeps: 12 characters/sec.

3 beeps: 20 characters/sec.

4 beeps: 30 characters/sec.

Note: Commands described in the [Key] - [Key] format are keys that must be pressed in

order on the keyboard. Commands described in the [Key]+[Key] format must be pressed

simultaneously.

Note: If the Num Lock, Caps Lock, and Scroll Lock lights are flashing in unison on the

keyboard, the other Unit has control of Computer A. You will not be able to use the

computer or issue commands until the other unit has finished using the computer.

Note: If the Extender is operating in Compatability Mode ([Ctrl] - [Ctrl] - [E] hotkey

sequence), you must enter [Ctrl] - [Ctrl] - [E] - [E] to access port E on the attached KVM

switch.

Using the Remote Unit

Like the Host Unit, the Remote Unit performs two functions: it allows a user at the

remote location (Computer B) to assume control of Computer A if the Host Unit is set to

Auto or Remote mode, and it also permits the user seated at Computer B to use that

system as though the KVM extender was transparent.

You can use either keyboard shortcuts or the mode switch on the top of the Host Unit to

alternate control between A and B.

LED Indicators

Instruction Manual

Mode “A” Indicator “B” Indicator

Remote Access (Computer A) On (solid) Off

Local Access (Computer B) Off On (solid)

Keyboard Shortcut Command Sequences

Beep Codes

Some of the keyboard command sequences you issue to the Remote Unit have multiple

possible settings. The Unit will beep to indicate what setting you have selected for the

command you issued. (A short beep followed by a long beep indicates an invalid

command.)

[Ctrl] - [Ctrl] - [Alt]+[E] (Compatibility Mode)

1 beep: disabled

2 beeps: enabled

[Ctrl] - [Ctrl] - [F11] (Remote Image Quality Adjustment)

1 beep: 0 ~ 130 feet (0 ~ 40 meters) of UTP cable length

2 beeps: 130 ~ 260 feet (40 ~ 80 meters) of UTP cable length

3 beeps: 260 ~ 390 feet (80 ~ 120 meters) of UTP cable length

4 beeps: 390 ~ 500 feet (120 ~ 150 meters) of UTP cable length

[Ctrl] - [Ctrl] - [F4] (Typematic Rate)

1 beep: 6 characters/sec.

2 beeps: 12 characters/sec.

3 beeps: 20 characters/sec.

4 beeps: 30 characters/sec.

Note: Commands described in the [Key] - [Key] format are keys that must be pressed in

order on the keyboard. Commands described in the [Key]+[Key] format must be pressed

simultaneously.

Instruction Manual

Standard Command With Compatibility Mode Enabled Description

[Ctrl] - [Ctrl] - [T] [Ctrl] - [Ctrl] - [T] Toggles console control between

Computer A and Computer B

[Ctrl] - [Ctrl] - [Esc] [Ctrl] - [Ctrl] - [Esc] Cancels the hotkey sequence

[Ctrl] - [Ctrl] - [Alt]+[E] [Ctrl] - [Ctrl] - [Alt]+[E]

Enables (2 beeps) or disables (1 beep)

Compatibility Mode so that the KVM

extender will work with a KVM switch

that also uses a [Ctrl] hotkey sequence

[Ctrl] - [Ctrl] - [1] [Ctrl] - [Ctrl] - [E] - [1] Switches control to Computer B

[Ctrl] - [Ctrl] - [2] [Ctrl] - [Ctrl] - [E] - [2] Switches control to Computer A (input

allowed only if the Host Unit is in

Remote or Auto mode)

[Ctrl] - [Ctrl] - [F2] [Ctrl] - [Ctrl] - [E] - [F2] Toggles console control between

Computer A and Computer B

[Ctrl] - [Ctrl] - [F4] [Ctrl] - [Ctrl] - [E] - [F4] Adjusts the typematic rate for improved

keyboard responsiveness

[Ctrl] - [Ctrl] - [F11] [Ctrl] - [Ctrl] - [E] - [F11]

Adjusts remote video quality based on

the length of UTP cabling between the

two computers (available only when

switched to Computer A)

[Ctrl] - [Ctrl] - [F12] [Ctrl] - [Ctrl] - [E] - [F12] Resets PS/2 mouse synchronization

Note: If the Num Lock, Caps Lock, and Scroll Lock lights are flashing in unison on the

keyboard, the other Unit has control of Computer A. You will not be able to use A until

the other Unit releases access to that computer.

Note: If the Extender is operating in Compatability Mode ([Ctrl] - [Ctrl] - [E] hotkey

sequence), you must enter [Ctrl] - [Ctrl] - [E] - [E] to access port E on the attached KVM

switch.

Specifications

RJ-45 Connector Pinout

Instruction Manual

Maximum Resolution 1024 x 768 (at maximum UTP cable length)

Actual maximum resolution varies by network cable length

Maximum Range 500 feet (150 meters)

Network Cabling Type Straight-through Unshielded Twisted Pair (UTP) Cat. 5+

Connectors Each, Host and Remote Unit

2 x HD-15 female (1 x KVM, 1 x console VGA)

1 x RJ-45

2 x PS/2 keyboard/mouse (for console)

1 x Power (optional)

Power Adapter 9V DC, 600mA, center positive (per Unit)

(Optional; only required when connected using a

conventional KVM switch)

Andere Handbücher für SV565UTP

Inhaltsverzeichnis

Andere StarTech.com Extender Handbücher

StarTech.com

StarTech.com 8STUSB2001EXTV Bedienungsanleitung

StarTech.com

StarTech.com ST121SHD50 Bedienungsanleitung

StarTech.com

StarTech.com ST121UTPMINI Bedienungsanleitung

StarTech.com

StarTech.com 410VDSLEXT Bedienungsanleitung

StarTech.com

StarTech.com ST121HD20FXA Bedienungsanleitung

StarTech.com

StarTech.com ST222HDBT Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB221EXT Bedienungsanleitung

StarTech.com

StarTech.com USB2G4LEXT2NA Bedienungsanleitung

StarTech.com

StarTech.com ST122UTPA Bedienungsanleitung

StarTech.com

StarTech.com 8STST121HDBT20S Bedienungsanleitung

StarTech.com

StarTech.com ST121UTPMINI Bedienungsanleitung

StarTech.com

StarTech.com 110VDSLEXT Bedienungsanleitung

StarTech.com

StarTech.com ST121HD20L Bedienungsanleitung

StarTech.com

StarTech.com EOC110K Systemhandbuch

StarTech.com

StarTech.com STUTPRXWAL Bedienungsanleitung

StarTech.com

StarTech.com SV565HDIP Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBTE Bedienungsanleitung

StarTech.com

StarTech.com STDHVHDBT Bedienungsanleitung

StarTech.com

StarTech.com ST12MHDLAN4K Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com ST121USBHD Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP Bedienungsanleitung

StarTech.com

StarTech.com 110VDSLEXT Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung