StarTech.com 410VDSLEXT2 Bedienungsanleitung

Manual Revision: 12/18/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

410VDSLEXT2

1 Port to 4 Port 10/100Mbps VDSL2 Ethernet Extender

Kit over Single Pair Wire – 1 km

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Product Overview ..................................................................................2

Installation .............................................................................................4

Hardware Installation ............................................................................................................................. 4

DIP Switch Settings - Transmitter ........................................................5

Conguration..........................................................................................7

Web Interface ............................................................................................................................................. 7

Welcome Screen........................................................................................................................................ 7

System........................................................................................................................................................... 8

Port Management..................................................................................................................................... 11

VLAN .............................................................................................................................................................. 14

QoS Setting ................................................................................................................................................. 16

Security Filter.............................................................................................................................................. 19

VDSL Setting ............................................................................................................................................... 20

Connector Architecture ......................................................................................................................... 22

Resetting Your Device.............................................................................................................................. 23

Appendix...................................................................................................................................................... 23

Technical Support ..................................................................................25

Warranty Information............................................................................25

Instruction Manual

Introduction

Packaging Contents

• 1x 1 Port VDSL2 Ethernet Transmitter

• 1x 4 Port VDSL2 Ethernet Receiver

• 2x Universal Power Adapters (NA/UK/EU)

• 1x RJ45 to VDSL2 Cable

• 1x RJ11 Cables

• 1x Instruction CD

• 1x Instruction Manual

System Requirements

• 10/100 Mbps Ethernet Network

• Available AC electrical outlets

• RJ11 Cable or RJ11 lines in building infrastructure

Instruction Manual

DC Input

LED Indicators

RJ11/RJ45 VDSL

Line Port

RJ11 VDSL Line Port

RJ45

Ports

DC Input

Reset

Receiver Unit

Transmitter Unit

DIP

Switch

RJ45 Port

Transmitter Unit

Receiver Unit

Product Overview

Front / Side View

Rear View

Instruction Manual

LED Displays

Transmitter Unit

LAN LED Display

LED Blinking ON OFF

1Activity Link up Link down

2100 Mbps 10 Mbps

3Full duplex Half duplex

VDSL LED Display

LED Blinking ON OFF

1Activity Device

Power On

Device Power O

2-CPE Mode CO Mode

3Slowly: Idle

Quickly: Training Linked Oine

LED Blinking ON OFF

PWR Device Power

Device

Power O

SYS System Activated System

Running

CO CO Mode On

CPE CPE Mode On

LINK

Activity

Slowly: Start Connection

Quickly: Data Transmit

Linked

ALM Connection Error

Receiver Unit

Instruction Manual

Installation

Hardware Installation

Transmitter Unit

1. Connect the provided power adapter from an AC electrical outlet to the DC Input on

the Transmitter Unit. The “PWR” LED should light up solid.

2. Set all four of the DIP switches to the upward (OFF) position. This places the unit in

CO mode.

3. Connect an RJ45 Ethernet cable to the RJ45 LAN Port on the Transmitter Unit.

4. Connect the other end of the Ethernet cable into your Ethernet network device (eg:

switch, Ethernet modem).

5. Connect an RJ11 phone cable into the VDSL Port on the Transmitter Unit.

6. Connect the opposite end of the RJ11 cable to the DSL Port on the Receiver Unit (or

to your buildings RJ11 phone line infrastructure, depending on your setup).

Optional: Congure DIP switches 2 through 4 as necessary (see “DIP Switch Settings”

section below).

Receiver Unit

1. Place the Receiver Unit at the end-point location.

2. Connect the provided power adapter from an AC electrical outlet to the DC Input on

the Receiver Unit. The “PWR” and “SYS” LED should light up solid.

3. If not previously completed, connect the RJ11 cable that was inserted into the RJ11

VDSL Port on the Transmitter Unit directly to the DSL Port on the Receiver Unit (or

from your buildings existing RJ11 analog telephone wiring, depending on the setup

from step 6 above.

4. If the Transmitter and Receiver Units are able to successfully communicate with each

other, the “LINK” LED should light up solid.

5. Connect each computer or Ethernet networking device to an available RJ45 Port

on the Receiver Unit. The respective “LAN” LED on each individual RJ45 Port should

light up to indicate a successful physical connection.

Instruction Manual

DIP Switch Settings - Transmitter

The Transmitter Unit has a 4-position DIP switch for conguration of Side, Channel,

Rate Limit, and SNR.

For initial setup, DIP switch 1 is usually set to the upward (OFF) position, ensuring the

unit is set to CO mode (Receiver Unit set to CPE mode by default).

When using the 410VDSLEXT2, one end (Transmitter or Receiver) must always be set to

“CO” mode, while the opposite end must always be set to “CPE” mode.

Setting each unit to CO or CPE mode is usually based on which direction you want

the most bandwidth delivered. “Download” bandwidth, data sent from CO to CPE, is

generally higher than “Upload” bandwidth from CPE to CO.

• If you need higher bandwidth from the Transmitter Unit to the Receiver Unit, set DIP

switch 1 to the upward (OFF) position.

• If you need higher bandwidth from the Receiver Unit to the Transmitter Unit, set DIP

switch 1 to the downward (ON) position.

See the “Conguration Mode Select” section below to set the Receiver Unit to the

appropriate CO or CPE mode based on the mode that was set on the Transmitter Units

DIP Switch setting.

Pin 1 - CO, CPE Switch

OFF:If Pin 1 is in the OFF position, the Transmitter Unit will operate in Central Oce

(CO) mode.

ON: If Pin 1 is in the ON position, the Transmitter Unit will operate in Customer Premise

Equipment (CPE) mode.

Pin 2 - Interleave Noise Protection

Instruction Manual

Pin 4 - General Protection

OFF: If Pin 4 is in the OFF position, the Transmitter Unit will operate with a SNR ratio up

to 9 dB.

ON: If Pin 4 is in the ON position, the Transmitter Unit will operate with a SNR ratio of

6 dB.

OFF: If Pin 2 is in the OFF position, the Transmitter Unit will operate in Interleave mode,

with communication protection for up to 250ms of impulse noise with latency less

than 6 ms

ON: If Pin 2 is in the ON position, the Transmitter Unit will operate in Fast mode, with

direct data transmissions having less than 1ms of latency.

Pin 3 - Band Plan

OFF: If Pin 3 is in the OFF position, the Transmitter Unit will operate in Symmetric

mode, with both downstream and upstream transmissions operating on the G.997

band plan.

ON: If Pin 3 is in the ON position, the Transmitter Unit will operate in Asymmetric mode,

with asymmetric short range transmissions operating at the highest available line rate.

Inhaltsverzeichnis

Andere StarTech.com Extender Handbücher

StarTech.com

StarTech.com ST121HDBTL Bedienungsanleitung

StarTech.com

StarTech.com ST121UTPMINI Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB110EXT Bedienungsanleitung

StarTech.com

StarTech.com 410VDSLEXT Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com USB2G4LEXT2 Bedienungsanleitung

StarTech.com

StarTech.com USB3004EXT2 Bedienungsanleitung

StarTech.com

StarTech.com ST122UTPA Bedienungsanleitung

StarTech.com

StarTech.com 8STST121HDBT20S Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB221EXT Bedienungsanleitung

StarTech.com

StarTech.com VS321HDBTK Bedienungsanleitung

StarTech.com

StarTech.com 4K70IC-EXTEND-HDMI Bedienungsanleitung

StarTech.com

StarTech.com WIFI2VGA Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPUL Bedienungsanleitung

StarTech.com

StarTech.com PS2UTPEXT Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP23GB Bedienungsanleitung

StarTech.com

StarTech.com ST121WHDS Bedienungsanleitung

StarTech.com

StarTech.com SV565LANDUA Bedienungsanleitung

StarTech.com

StarTech.com COMPUTPEXTA Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB204EXTFIB Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB100EXT Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP Bedienungsanleitung

StarTech.com

StarTech.com STDHVHDBT Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung