StarTech.com VID2HDMITV Handbuch
Composite/S-Video & Stereo Audio HDMI Scaler / Converter
VID2HDMITV Instruction Guide
The Professionals’ Source For Hard-to-Find Computer Parts
Video Scaler
* Actual product may vary from photo
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 1
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 2
1
TTaabblleeooffCCoonntteennttss
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Connecting Devices to the Video Scaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Using the Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Picture Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Output Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Supported Video Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Warranty Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 1
2
Introduction
Thank you for purchasing a StarTech.com video scaler. This device allows you to convert
composite, S-Video and accompanying audio signals to an HDMI connection, for use on
a PC or high definition display. Offering a variety of output video resolutions,
VID2HDMITV also provides an on-screen display menu, to help simplify fine tuning and
picture adjustment.
Features
• Motion adaptive 3D Y/C separation comb filter
• Advanced 3D motion adaptive de-interlacing
• Automatic 2:2 / 3:2 film mode detection
• Supports 50Hz to 60Hz frame rate conversion
• OSD menu to adjust picture quality, color, contrast and brightness
• Built-in 8 bit DAC for RGB or YPbPr output
• Automatic NTSC/PAL video format detection and switching
Before You Begin
Package Contents
• 1 x Video to HDMI Scaler/Converter
• 1 x Remote control
• 1 x Instruction Manual
• 1 x Universal Power Adapter
Site Preparation
Ensure you have the necessary cables to connect your video source (such as a DVD
player) to the video scaler. Note that if you have previously used the device with a
standard television, you can most likely use those cables to connect the item to the video
scaler. The video scaler should be in close proximity to the video source and be
connected using high-quality cables for the best possible results.
Need more cables? Contact your dealer or visit www.startech.com for more
information.
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 2
3
Connecting Devices to the Video Scaler
1. Disconnect your high-resolution display from its existing video connections.
2. Place the video scaler near the video source and connect the power adapter to a
suitable wall outlet. Connect the opposite end to the DC 5V 2A connector on the rear
panel of the video scaler.
3. Connect the cable you used to connect your video source to its previous video display
(usually labeled as VIDEO OUT, or similar) as removed in step 1 to the CV or SV
connector on the rear of the video scaler as appropriate. The connector you use will
depend on the type of cable the video source uses.
4. As necessary, connect the audio signal source to the AUDIO L & R ports on the rear
panel of the scaler.
5. Apply power to the scaler, by pressing the POWER button.
UUssiinnggtthheeMMeennuuOOppttiioonnss
To begin customizing the video image, press the menu button to bring up the following
OSD menu:
To navigate through the OSD menu system:
1. Use the +and -keys on the front of the video scaler to move between options.
2. Use the MENU key to select an item to adjust or display a sub-menu.
3. Once an item is selected, use the +and -keys to adjust the setting.
4. When you are satisfied with your changes, press MENU to activate the setting.
5. You can continue to adjust other settings, or select Exit from the OSD menus until
the OSD disappears.
VID2HDMITV
Rear Panel
1DC power jack
2Composite Video
3S-Video
4Audio input L/R
5HDMI output
1POWER
2INPUT
3Remote sensor
4MENU
5+, -
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 3
4
Picture Adjust
Use the +,-buttons to move the cursor to the desired parameter. Press the MENU
button to confirm your selection. At this point, the selected parameter will turn red, and
you can use the +,-buttons to increase or decrease the value of the parameter. Once
the necessary adjustments have been made, Press the MENU button to apply the
change.
Output select
When selected, this menu will allow you to change the output resolution of the display:
Use the +,-buttons to move the cursor to the desired resolution/refresh rate. Press the
MENU button to confirm your selection. Please note: Selecting a resolution/refresh rate
that is not supported by your display, may damage the display. Please consult the
documentation that accompanied the display unit at the time of purchase.
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 4
5
UUssiinnggtthheeRReemmootteeCCoonnttrrooll
1. Display: Press this button to display the input source
and output resolution on the screen.
2. POWER: Power ON/OFF button.
3. VGA~1080i: Press to select your desired output
resolution.
4. PICTURE: Press this button to enter the picture adjust
submenu. Use the +and -buttons to move
the cursor up/down to the desired
parameter, press PICTURE again to
confirm.
5. +/-: Press to move the cursor selection up/down to the
desired parameter, or press to increase/decrease
the setting value.
6. RESET: Press to reset all configurations back to
factory default value.
7. EXIT: Pressing this button will exit the OSD.
8. VIDEO: Press this button to select composite video
input.
9. SVIDEO: Press the button to select SVideo input.
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 5
6
TTrroouubblleesshhoooottiinngg
Problem: No image is being displayed from the video source or the OSD.
Cause: The input setting or output timing (resolution and refresh rate) is incorrect.
Resolution: a) With an HDTV display, adjust the settings back to the default setting for
your display type by pressing the MENU and - buttons simultaneously.
With a computer monitor, press the +and -buttons simultaneously to
return to XGA resolution.
b) Ensure all cables are securely connected.
Problem: The image is distorted or blurry.
Cause: The output timing settings/image quality settings are not optimized, or there is
interference degrading the cable signal.
Resolution: a) Adjust the timing settings and image settings using the menu system to
improve image quality and ensure the video source is working normally.
b) Use the shortest cable length possible, and ensure that they are of a high
quality. Heavily-shielded cables with gold-plated connectors offer
superior performance and signal protection. Do not use converters or
extension cables unless they were supplied with the video scaler.
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 6
7
SSppeecciiffiiccaattiioonnss
General specifications
Output Signal specifications
HDMI connector pin assignment
Input signal levels
Video@1Vp-p, 75 ohm,
Y@1 Vp-p, 75 ohm
Color@ 0.7 Vp-p, 75 ohm
Output Format Digital RGB
Output Connector HDMI Type A female
Output Signal Bit stream
Weight 400g
Dimensions 125(W) x 123(D) x 30(H) mm
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 7
8
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit our
Web site to access our comprehensive selection of online tools, documentation, and
downloads:
www.startech.com/support
Warranty Information
This product is backed by a one-year warranty. In addition, StarTech.com warrants its
products against defects in materials and workmanship for the periods noted,
following the initial date of purchase. During this period, the products may be
returned for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its products
from defects or damages arising from misuse, abuse, alteration, or normal wear and
tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the actual
price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement
may not apply to you.
Revised: September 13, 2006
VID2HDMITV.qxp 9/13/2006 2:40 PM Page 8
Andere Handbücher für VID2HDMITV
1
Inhaltsverzeichnis
Andere StarTech.com Medienkonverter Handbücher
StarTech.com
StarTech.com 8STPATA2SATA3 Bedienungsanleitung
StarTech.com
StarTech.com COMP2VGA Handbuch
StarTech.com
StarTech.com ET91000SC2 Bedienungsanleitung
StarTech.com
StarTech.com UVCHDCAP Bedienungsanleitung
StarTech.com
StarTech.com USB32DVCAPRO Bedienungsanleitung
StarTech.com
StarTech.com 8STMCM10GSFP Bedienungsanleitung
StarTech.com
StarTech.com DVI2VGA Bedienungsanleitung
StarTech.com
StarTech.com ET1000SM40LC Systemhandbuch
StarTech.com
StarTech.com 8STVID2VGATV2 Bedienungsanleitung
StarTech.com
StarTech.com ET90110SC Handbuch
StarTech.com
StarTech.com ET90110SM302 Bedienungsanleitung
StarTech.com
StarTech.com VID2HDCON Bedienungsanleitung
StarTech.com
StarTech.com ET9003SC Handbuch
StarTech.com
StarTech.com 8STET91000LCOAM Bedienungsanleitung
StarTech.com
StarTech.com ET91000LC Bedienungsanleitung
StarTech.com
StarTech.com ET91000LC Systemhandbuch
StarTech.com
StarTech.com MCMGBSCMM055 Bedienungsanleitung
StarTech.com
StarTech.com PATA2SATA2 Bedienungsanleitung
StarTech.com
StarTech.com VID2VGATV Bedienungsanleitung
StarTech.com
StarTech.com SLMPT2HD Bedienungsanleitung
