StarTech.com SV231HDMIUA Bedienungsanleitung

Manual Revision: 05/01/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

SV231HDMIUA

2 Port USB HDMI KVM Switch with Audio

and USB 2.0 Hub

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Installation ..............................................................................................2

Front View................................................................................................2

Rear View .................................................................................................2

Hardware Installation .............................................................................................................................. 3

Driver Installation...................................................................................................................................... 4

Operation ................................................................................................4

Front Panel................................................................................................................................................... 4

HotKey Control........................................................................................................................................... 5

Alternative Hotkey Commands............................................................................................................ 7

Change Leading Hotkey......................................................................................................................... 8

Specications..........................................................................................9

Technical Support ..................................................................................10

Warranty Information............................................................................10

Instruction Manual

Introduction

The SV231HDMIUA 2-port USB HDMI® KVM Switch lets you control two USB-enabled

multimedia computers or devices with HDMI video interfaces, using a single peripheral

set/console (USB keyboard, mouse, monitor, speakers and microphone).

A highly versatile KVM solution, the USB HDMI KVM Switch features an integrated

2-port USB 2.0 hub that lets selected computers access shared high speed USB devices,

eliminating the cost of duplicate USB peripheral purchases.

Ensuring high quality video capability, the HDMI KVM switch supports HD resolutions

of up to 1920 x 1200. Oering genuine digital signal transmission over the cable, this

switch can be used to share one HD panel between multiple HDMI sources such as Blu-

Ray players, Video Game consoles and HD media centers.

The switch also supports audio and microphone switching functions and allows you to select

connected computers, USB device hub ports and audio/mic channels either simultaneously

or independently using either front-panel push-buttons or keyboard hotkeys.

Packaging Contents

• 1x 2 Port HDMI KVM

• 1x Package of Rubber feet

• 1x Power Adapter

• 1x User Manual

System Requirements

• HDMI and USB enabled computer systems

• HDMI enabled display device (e.g. monitor, projector, TV, etc.)

• Standard 104-key wired USB keyboard

• Standard 3-button wired USB mouse

Instruction Manual

Installation

NOTE: Prior to the installation, please power o all devices that will be connected to

this system.

Ensure that all devices you will connect are properly grounded.

Place cables away from uorescent lights, air conditioners, and machines that are likely

to generate electrical noise.

If you experience any problems using a USB KVM switch, the following BIOS setup

changes may be necessary for PC users (not necessary for Mac users):

• Set HALT ON ERROR to ALL BUT KEYBOARD.

• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.

Dierent systems may use dierent naming, so contact your system manufacturer for

further assistance with these settings.

Front View

Rear View

Port Selection

Link LED

Port Selection

Button

Instruction Manual

Hardware Installation

1. Plug a monitor/display into the Console HDMI connector; plug a USB keyboard and

a USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch.

2. Use a male-to-male HDMI video cable to connect the HDMI connector on the

computer’s/devices’video card, to one of the KVM’s PC ports (ie. PC1)

3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector) for the

PC port used in Step 2, and the USB port on the computer/device (type A, at connector).

4. Use a male-to-male 3.5mm mini-jack audio cable to connect the speaker and

microphone connectors on the computer/device to the KVM’s speaker/mic ports for

the PC port used in Step 2.

5. Repeat for Steps 2 thru 4 for each PC port on the KVM switch, or each computer/

device you wish to use on the KVM.

6. OPTIONAL: Connect any other USB peripherals you wish to share between the

connected computers/devices to the extra USB Hub ports on the Console side.

7. Connect the external power adapter from a wall outlet to the power connector on

the rear panel of the KVM switch.

8. Power up the rst computer/device and wait for it to fully boot and test keyboard/

mouse functionality.

9. Once operation has been successfully conrmed, switch to the next port and power

up that computer/device and conrm.

10. Once completed for all computers/devices connected to the KVM switch, you

should be able to switch between ports freely.

*Console setup

Instruction Manual

Driver Installation

No driver installation is required for the KVM switch, as the keyboard and mouse

use generic USB keyboard/mouse drivers that are already installed on any operating

system that fully supports USB.

Operation

Front Panel

Port Selection/Link LED

The LED turns green when the connected computer is powered-on. The corresponding

LED will also illuminate red when that PC port is currently selected.

Port Selection Button

Pushing the front panel “Select”button toggles between the PC ports on the KVM switch.

Instruction Manual

HotKey Control

A Hotkey command is a short keyboard sequence for selecting a computer, activating

computer scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes

(successively within 0.2 seconds) followed by one or two more keystrokes. A built-in

tone generator creates a high-pitch beep for correct hotkey command; otherwise, one

low-pitch beep is generated for errors and the bad key sequence will not be forwarded

to the selected computer.

NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT>

followed by pressing left <CTRL> once, which will enable / disable the hotkey feature.

To select a computer:

Left <CTRL> + Left <CTRL> + <1>

(Example: Selects the computer at port 1.)

Left <CTRL> + Left <CTRL> + <2>

(Example: Selects the computer at port 2.)

NOTE: Do not use the keypad on the right-side of the keyboard.

Auto Scan

The KVM automatically scans through the powered-on computers in sequence on a

xed time interval (see Scan Time below).

To start Auto Scan:

Left <CTRL> + Left <CTRL> + <F1>

To abort the Auto Scan mode, press the left <CTRL> key twice.

NOTE: When Auto Scan detects any keyboard or mouse activity, it suspends the

scanning till the activity stops; it then resumes with the next computer in sequence.

The length of the Auto Scan interval (Scan Rate) is adjustable, see below.

Instruction Manual

Manual Scan allows users to manually switch back and forth between powered-on computers.

Left <CTRL> + Left <CTRL> + <F2>

To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To

abort the Manual Scan, press any other key.

Scan Time

Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15

and 30 seconds.

Note: Scan Time is set to 3 seconds by default.

To adjust Scan Rate, set the scan time of duration before switching to the next computer:

Left <CTRL> + Left <CTRL> + <F3>

The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or

30 seconds respectively.

Audio Lock

There are two options for Audio Lock: ON and OFF. When ON, audio selection follows

computer selection. When OFF, the current port’s audio is used for all other ports. It

is useful if you want to listen to a particular computer’s audio signal while operating

other computers.

Left <CTRL> + Left <CTRL> + <F5>

The KVM switch beeps once or twice corresponding to ON and OFF respectively.

To change which port the audio is following to the currently selected port, press the

following hotkey:

Left <CTRL> + Left <CTRL> + <A>

Instruction Manual

Alternative Hotkey Commands

In addition to the Left <CTRL> + Left <CTRL> hotkeys, there are two alternative hotkey

sequences available.

1. For the following operations, users may press <ScrollLock> twice instead of pressing

left <CTRL> twice.

To select a computer:

(Example: Select the computer at port 1.)

(Example: Select the computer at port 2.)

NOTE: Do not use the keypad at the right of the keyboard.

2. For those keyboards that do not have or support <ScrollLock>, please press and

HOLD the Left <SHIFT> and press <NumLock> twice instead of pressing Left

<CTRL> twice.

To select a computer:

hold Left <SHIFT> + press <NumLock> + press <NumLock>

then release <SHIFT> + press <1>

Example: Select the computer at port 1.)

hold Left <SHIFT> + press <NumLock> + press <NumLock>

then release <SHIFT> + press <2>

(Example: Select the computer at port 2.)

NOTE: Do not use the keypad at the right of the keyboard.

Andere Handbücher für SV231HDMIUA

Inhaltsverzeichnis

Andere StarTech.com Schalten Handbücher

StarTech.com

StarTech.com SV1107IPEXT Bedienungsanleitung

StarTech.com

StarTech.com 8STIES81GPOEW Bedienungsanleitung

StarTech.com

StarTech.com SV231DD2DUA Bedienungsanleitung

StarTech.com

StarTech.com SV431DD2DU3A Bedienungsanleitung

StarTech.com

StarTech.com IES61002POE Bedienungsanleitung

StarTech.com

StarTech.com USB421HS Bedienungsanleitung

StarTech.com

StarTech.com 8STSV431DPDDUA2 Bedienungsanleitung

StarTech.com

StarTech.com IES101G2SFPW Bedienungsanleitung

StarTech.com

StarTech.com IES81GW Leitfaden

StarTech.com

StarTech.com SV231HU34K6 Bedienungsanleitung

StarTech.com

StarTech.com 5G4AIBS-USB-HUB-NA Bedienungsanleitung

StarTech.com

StarTech.com VS420RDVIA Bedienungsanleitung

StarTech.com

StarTech.com ICUSB2322I Bedienungsanleitung

StarTech.com

StarTech.com SV831DVIU Bedienungsanleitung

StarTech.com

StarTech.com SV441DUSBI Bedienungsanleitung

StarTech.com

StarTech.com ST3300G3UA Bedienungsanleitung

StarTech.com

StarTech.com DS52000 Bedienungsanleitung

StarTech.com

StarTech.com 8 Port StarView CAT5 UTP KVM Bedienungsanleitung

StarTech.com

StarTech.com ST1030USBM Bedienungsanleitung

StarTech.com

StarTech.com MSTCDP122HD Bedienungsanleitung

StarTech.com

StarTech.com ST4202USB Bedienungsanleitung

StarTech.com

StarTech.com SV431DPU3A2 Bedienungsanleitung

StarTech.com

StarTech.com MSTMDP122DP Bedienungsanleitung

StarTech.com

StarTech.com SV431DVGAU2A Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung