StarTech.com SV431DPUA Bedienungsanleitung

DisplayPort KVM Switch

4-Port Professional USB,

DisplayPort KVM Switch

with Audio

SV431DPUA

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver•

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company

in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction..................................................................... 1

Packaging Contents.....................................................................1

System Requirements .................................................................1

Installation....................................................................... 1

Hardware Installation...................................................................2

Front View....................................................................................2

Rear View ....................................................................................2

Driver Installation.........................................................................4

Operation......................................................................... 4

Front Panel ..................................................................................4

HotKey Control ............................................................................5

Alternative Hotkey Commands ....................................................8

Speciﬁcations.................................................................. 10

Technical Support........................................................... 11

Warranty Information...................................................... 11

Introduction

Packaging Contents

1 x SV431DPUA KVM switch•

1 x Power Adapter•

1 x Rubber Feet•

1 x Instruction Manual•

System Requirements

DisplayPort enabled computer system•

USB enabled computer system•

Standard 104-key USB keyboard•

Standard 3-button USB mouse•

Installation

NOTE: Prior to the installation, please power off all devices that will be

connected to this system.

Ensure that all devices you will connect are properly grounded.

Place cables away from ﬂuorescent lights, air conditioners, and

machines that are likely to generate electrical noise.

If you experience any problems using a USB KVM switch, the

following BIOS setup changes may be necessary for PC users and not

necessary for Mac users:

Set HALT ON ERROR to ALL BUT KEYBOARD.•

In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set•

USB IRQ to ENABLED.

Different systems may use different naming, so contact your system

manufacturer for further assistance with these settings.

Hardware Installation

Front View

Rear View

USB Hub

ports

USB keyboard/

mouse ports

Console

DisplayPort

port

External

power port

PC4 Port PC3 Port PC2 Port PC1 Port

3.5mm speaker/

MIC ports

Port

Selection

Buttons

PC Port Power/

Selection LED

KVM Power

LED

*installation pictures are representations only

Plug a monitor into the Console’s DisplayPort connector; plug a USB1.

keyboard and a USB mouse into the dedicated USB keyboard and

mouse ports on the KVM switch.

Use a male-to-male DisplayPort video cable to connect the2.

DisplayPort connector on the computer’s video card, to one of the

KVM’s PC ports (i.e. PC1)

Use a USB type A-B Cable to connect the KVM’s USB port (type B,3.

square connector) for the PC port used in Step 2, and the USB port

on the computer (type A, ﬂat connector).

Repeat for Steps 2 and 3 for each PC port on the KVM switch, or4.

each computer you wish to use on the KVM.

OPTIONAL:5. Connect any other USB peripherals you wish to share

between the connected computers/devices to the extra USB Hub

ports on the Console side.

Connect the external power adapter from a wall outlet to the power6.

connector on the rear panel of the KVM switch.

Power up the ﬁrst computer/device and wait for it to fully boot and7.

test keyboard/mouse functionality.

Once operation has been successfully conﬁrmed, switch to the next8.

port and power up that computer/device and conﬁrm.

Once completed for all computers/devices connected to the KVM9.

switch, you should be able to switch between any ports freely.

Driver Installation

No driver installation is required for the KVM switch, as the keyboard

and mouse use generic USB keyboard/mouse drivers that are already

installed on any operating system that fully supports USB.

Operation

Front Panel

PC Link/Selection LED

The LED turns green when the connected computer is powered-on.

The corresponding LED will also illuminate red when that PC port is

currently selected.

Port Selection Button

Each push button on the front of the KVM switch corresponds with a

PC port. Pressing that button will immediately select that port.

AutoScan

The system automatically scans through the power-on computers in

sequence with a ﬁxed interval (see Scan Time below).

To activate AutoScan, press front panel push buttons “3” and “4”

simultaneously. The port selection LED will ﬂash during AutoScan.

AutoScan will select active computers only. To exit AutoScan mode,

just press any one of the front panel push buttons.

Scan Time

Four options are available for users to set the Scan Time duration, it

Includes 3, 8, 15 and 30 seconds.

Note: Scan Time is set to 3 seconds by default.

To change the Scan Time, press front panel buttons “1” and “2”

simultaneously. The unit will respond with beep(s) of 1, 2, 3 or 4 times

for a Scan Time of 3, 8, 15 or 30 seconds respectively.

HotKey Control

A Hotkey command is a short keyboard sequence for selecting a

computer, activating computer scan, etc. A hotkey sequence starts

with two left <CTRL> keystrokes ( successively within 0.2 seconds )

followed by one or two more keystrokes. A built-in buzzer generates a

high-pitch beep for correct hotkey command; otherwise, one low-pitch

beep is generated for errors and the bad key sequence will not be

forwarded to the selected computer.

NOTE: Press and hold Left <SHIFT> and press <NumLock> twice,

then release Shift followed by pressing left <CTRL> once, which will

enable / disable the hotkey feature.

To select a computer:

Left <CTRL> + Left <CTRL> + 1

(Example: Selects the computer at port 1.)

Left <CTRL> + Left <CTRL> + 2

(Example: Selects the computer at port 2.)

NOTE: Do not use the keypad on the right-side of the keyboard.

Auto Scan

The KVM automatically scans through the powered-on computers in

sequence on a ﬁxed time interval (see Scan Time below).

Note: The keyboard and mouse are not operable during Auto Scan.

To start Auto Scan:

Left <CTRL> + Left <CTRL> + F1

To abort the Auto Scan mode, press the left <CTRL> key twice. When

Auto Scan detects any keyboard or mouse activity, it suspends the

scanning till the activity stops; it then resumes with the next computer

in sequence. The length of the Auto Scan interval (Scan Time) is

adjustable, see below.

Manual Scan allows users to manually switch back and forth between

power-on computers.

Left <CTRL> + Left <CTRL> + F2

To select the previous or the next computer, press <UP> or <DOWN>

arrow keys. To abort the Manual Scan, press any other key.

Scan Time

Four options are available for users to set the Scan Time duration, it

Includes 3, 8, 15 and 30 seconds.

Note: Scan Time is set to 3 seconds by default.

To adjust Scan Rate, set the scan time of duration before switching to

the next computer:

Left <CTRL> + Left <CTRL> + F3

The KVM Switch generates 1 to 4 beeps indicating a scan time

duration for 3, 8, 15 or 30 seconds respectively.

Audio Stick

There are two options for Audio Stick: ON and OFF. When ON, audio

selection follows computer selection. When OFF, the current port’s

audio is used for all other ports. It is useful if you want to listen to a

particular computer’s audio signal while operating other computers.

Press Left <CTRL> + Press Left <CTRL> + Press F5

The KVM switch beeps once or twice corresponding to ON and OFF

respectively.

To change which port the audio is following to the currently selected

port, press the following hotkey:

Press Left <CTRL> + Press Left <CTRL> + Press A

USB-Port Rule

There are two settings for USB-Port Rule: ON or OFF.

When set to ‘ON’, the USB Hub ports follows computer selection.

When set to ‘OFF’, the USB Hub ports stays on the currently selected

PC port.

Inhaltsverzeichnis

Andere StarTech.com Schalten Handbücher

StarTech.com

StarTech.com DS15H54 Systemhandbuch

StarTech.com

StarTech.com SV431DVGAU2A Bedienungsanleitung

StarTech.com

StarTech.com ENTERPRISE CLASS SV1653DXI Bedienungsanleitung

StarTech.com

StarTech.com SV431HU34K6 Bedienungsanleitung

StarTech.com

StarTech.com IES101002SFP Bedienungsanleitung

StarTech.com

StarTech.com SV831DUSBGB Bedienungsanleitung

StarTech.com

StarTech.com SV1654DX4I Bedienungsanleitung

StarTech.com

StarTech.com IES81000POE Bedienungsanleitung

StarTech.com

StarTech.com HB30C3APDW Bedienungsanleitung

StarTech.com

StarTech.com DS81000 Handbuch

StarTech.com

StarTech.com SV231DVIUA Bedienungsanleitung

StarTech.com

StarTech.com DisplayPort MSTDP124DP Bedienungsanleitung

StarTech.com

StarTech.com SV231DPU2 Bedienungsanleitung

StarTech.com

StarTech.com MSTMDP123HD Bedienungsanleitung

StarTech.com

StarTech.com SV211 Bedienungsanleitung

StarTech.com

StarTech.com SV211HDUC Bedienungsanleitung

StarTech.com

StarTech.com ST4300USB3 Bedienungsanleitung

StarTech.com

StarTech.com RS24102V Bedienungsanleitung

StarTech.com

StarTech.com CPNT410IR Bedienungsanleitung

StarTech.com

StarTech.com HB30C3A1GEA Bedienungsanleitung

StarTech.com

StarTech.com VS421CPNTA Bedienungsanleitung

StarTech.com

StarTech.com SV431DL2DU3A Bedienungsanleitung

StarTech.com

StarTech.com 5port Bedienungsanleitung

StarTech.com

StarTech.com SV441DUSBI Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung