StarTech.com WFRAP433ACD Bedienungsanleitung

Manual Revision: 02/17/2016

For the latest information, technical specications, and support for

this product, please visit www.startech.com/WFRAP433ACD.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

WFRAP433ACD

Wall Plug AC750 Dual Band Wireless-

AC Access Point / Router / Repeater

*actual product may vary from photos

Instruction manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limit set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum

distance 0.5cm between the radiator and your body.

Déclaration d’exposition à la radiation

Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un

environnement non contrôlé. Cet équipement doit être installé et mis en marche à une

distance minimale de 0.5 cm qui sépare l’élément rayonnant de votre corps.

L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver

à leur proximité.

FCC ID: NZ3WS-WN566A2

IC: 11232A-WFRAP433

The Country Code Selection feature is disabled for products marketed in the US/Canada

The device, for operation in the band 5150–5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems.

Instruction manual

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction manual

Table of Contents

Introduction............................................................................................1

Packaging contents.................................................................................................................................. 1

System requirements............................................................................................................................... 1

Product diagram ....................................................................................2

Front view .................................................................................................................................................... 2

Bottom view................................................................................................................................................ 2

Back view...................................................................................................................................................... 3

About LED indicators.............................................................................4

Insert one of the wall plugs..................................................................5

Extend the existing wireless signal.....................................................5

Congure Wi-Fi repeater mode on the WFRAP433ACD.............................................................. 5

Use the network cable to congure Wi-Fi repeater mode ......................................................... 5

Wirelessly congure Wi-Fi repeater mode ....................................................................................... 6

Create a wireless access point..............................................................7

Use the device as a wireless router .....................................................8

Managing the WFRAP433ACD .............................................................9

Change the basic wireless settings..................................................................................................... 9

Change the WFRAP433ACD password.............................................................................................. 9

Back up and restore the WFRAP433ACD settings ......................................................................... 10

Connecting computers to the device..................................................10

Add a wireless computer to the WFRAP433ACD........................................................................... 10

Use the WFRAP433ACD to add a wireless computer................................................................... 11

Add a wired computer to the WFRAP433ACD................................................................................ 11

Instruction manual

Reset to the factory default settings ..................................................11

Technical support...................................................................................12

Warranty information............................................................................12

Instruction manual

Introduction

You can use the WFRAP433ACD to easily create a wireless network from your existing

wired network connection or extend the distance and performance of your Wi-Fi®

network throughout your home or oce. Simply plug the WFRAP433ACD into a

wall outlet and set up or enhance your wireless environment through one of three

selectable operating modes: access point, router, or repeater.

Packaging contents

• 1 x wall plug wireless-AC access point

• 3 x interchangeable wall plugs (NA/EU/UK)

• 1 x network cable

System requirements

• Available AC electrical outlet

System requirements are subject to change. For the latest requirements, please visit

www.startech.com/WFRAP433ACD.

Instruction manual

Product diagram

Front view

Power LED

LAN LED

WAN/LAN LED

Wi-Fi/WPS LED

Bottom view

WPS button

Reset button

Mode switch

LAN port

WAN/LAN port

Instruction manual

Back view

Wall plug interface

Wall plug

release button

Instruction manual

About LED indicators

The WFRAP433ACD features four LED indicators that are located on the front of the

device. For more information about what the LED indicators represent, consult the

table below.

LED LED behavior Meaning

Power (green) Illuminated Device is receiving power.

Not illuminated Device isn’t receiving power.

LAN (green)

Illuminated The LAN port is connected.

Blinking Data is being transferred to or from a

network device.

Not illuminated The LAN port is disconnected.

WAN/LAN (green)

Illuminated The WAN/LAN port is connected.

Blinking Data is being transferred to or from a

network device.

Not illuminated The WAN/LAN port is disconnected.

Wi-Fi/WPS (green)

Illuminated The Wi-Fi/WPS port is connected.

Blinking quickly Data is being transferred to or from a

network device.

Blinking slowly The Wi-Fi/WPS is in the process of

being connected.

Not illuminated The Wi-Fi/WPS port is disconnected.

Instruction manual

Insert one of the wall plugs

1. Select the appropriate wall plug for your region.

2. Grasp the wall plug by the blades and press it into the wall plug interface on the

WFRAP433ACD.

3. Turn the wall plug clockwise until you hear a click.

To remove a wall plug from the WFRAP433ACD, press the wall plug release button,

turn the wall plug counterclockwise and pull it away from the wall plug interface.

Extend the existing wireless signal

When you use the WFRAP433ACD in repeater mode, the existing wireless signal is

copied and reinforced to extend the signal coverage. The WFRAP433ACD works well in

large houses, oces, warehouses, or other spaces where the existing wireless signal is

weak.

You can congure the WFRAP433ACD to extend the wireless signal in one of three

ways: On the WFRAP433ACD itself, using the included network cable, or wirelessly.

Congure Wi-Fi repeater mode on the WFRAP433ACD

1. Check the documentation that came with your wireless router to make sure that it

supports WPS.

2. On the WFRAP433ACD, move the Mode switch to AP/Repeater.

3. Insert the wall plug for your region and plug the WFRAP433ACD into an AC wall

outlet.

4. Press and hold the WPS button on the WFRAP433ACD for ten seconds. The Wi-Fi/

WPS LED indicator will start to blink.

5. While the Wi-Fi/WPS LED is blinking, press the WPS button on your wireless router

for ve seconds.

The WFRAP433ACD will now connect to your wireless router and copy the wireless key.

You can access the WFRAP433ACD using the SSID and wireless key of your wireless

router.

Use the network cable to congure Wi-Fi repeater mode

1. On the WFRAP433ACD, move the Mode switch to AP/Repeater.

2. Insert the wall plug for your region and plug the WFRAP433ACD into an AC wall

outlet.

3. Connect the network cable to the LAN port on the WFRAP433ACD and the port on

your computer.

4. On your computer, open a web browser and enter http://192.168.10.1 or http://

Inhaltsverzeichnis

Andere StarTech.com Drahtloser Zugangspunkt Handbücher

StarTech.com

StarTech.com R300WN22OP5 Bedienungsanleitung

StarTech.com

StarTech.com WIFIDETG Bedienungsanleitung

StarTech.com

StarTech.com AP300WN2X2W Bedienungsanleitung

StarTech.com

StarTech.com R300WN22GA Bedienungsanleitung

StarTech.com

StarTech.com WFREPEAT300N Bedienungsanleitung

StarTech.com

StarTech.com AP150WN1X1OD Bedienungsanleitung

StarTech.com

StarTech.com R300WN22OP5G Bedienungsanleitung

StarTech.com

StarTech.com WAP1011BB Handbuch

StarTech.com

StarTech.com R300WN22GA Bedienungsanleitung

StarTech.com

StarTech.com R300WN22MOD Bedienungsanleitung

StarTech.com

StarTech.com WAP1055BG Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung