Steepletone SMC2014 BT Bedienungsanleitung

Modular Twin CD Player / Recorder

with Radio,Turntable, Cassette Player,

Aux & Bluetooth Playback

INSTRUCTION MANUAL

(Please read before use)

AUX-IN

CAUTION:

Usage of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous radiation exposure.

This unit should not be adjusted or repaired by anyone except qualified service personnel.

IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS

PLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE APPLICABLE TO YOUR EQUIPMENT.

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Water and Moisture - The appliance should not be used near water, for example, near a bathtub,

washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool and the like.

6. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by

the manufacturer.

7. Ventilation - The appliance should be situated so that its location or position does not interfere with its

proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface

that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet

that may impede the flow of air through the ventilation openings.

8. Heat - The appliance should be situated away from heat sources such as radiators, heaters, ovens,

cookers or other appliances (including amplifiers) that produce heat.

9. Power Sources - The appliance should be connected to a power supply only of the type described in the

operating instructions or as marked on the appliance.

10.Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of

an appliance is not impeded.

11.Power - Cord Protection –Power supply cords should be routed so that they are not likely to be walked on

or squeezed by items placed upon or against them, paying particular attention to where the cord is

connected to the power plug, and the point where they exit from the appliance.

12.Cleaning - The appliance should be cleaned only as recommended by the manufacturer.

13.Antenna - This product is designed for use with the antenna attached and should not be connected to any

other external antennas.

14.Non-use Periods - The power cord of the appliance should be unplugged from the wall outlet when left

unused for a long period of time.

15.Object and Liquid Entry - Care should be taken so objects do not fall and liquids are not spilled into the

enclosure through openings.

16.Damage Requiring Service - The appliance should be serviced by qualified service personnel only when:

a)The power supply cord of the plug has been damaged.

b) Objects have fallen, or liquid has been spilled into the appliance.

c) The appliance has been exposed to rain.

d) The appliance does not appear to operate normally or exhibits a marked change in performance.

e) The appliance has been dropped, or the enclosure damaged.

17. Servicing - The user should not attempt to service the appliance beyond that described in the operating

instructions. All other servicing should be referred to qualified service personnel.

E-1

LOCATION OF CONTROLS

1) LCD Display

2) BLUETOOTH LED indicator

3) Standby LED Indicator

4) Main On/Off button

5) MEM/CLK-ADJ button

6) –PLAY MODE Button

7) CLK/DISPLAY Button

8) –FOLDER/PREset UP Button

9) –FOLDER /PREset DOWN Button

10) VOLUME knob

11) –CD Skip Up/TUNE /Down Button

12) -- Stop /ST-MOno button

13) –CD Play/Pause /Band button

14) –Open/Close Button

15) 3.5mm dia. Headphone Jack

16) 3.5mm dia. AUX-IN Jack

17) CD 2 –CD Skip Up /Down Button

18) CD 2 –CD Stop Button

19) CD 2 –CD Play/Pause Button

20) CD 2 –Open/Close Button

21) Tape Forward / Eject Button

22) Cassette Door Cover

23) Infra-red Remote Sensor

24) FUNCTION button

25) PRESET EQ button

26) FINALIZE Button

27) ERASE Button

28) CD 2 –‘TS’button (Track Separation)

29) CD 2 RECord Button

30) –CD Door

31) CD 2 –CD Door

32) CD 2 Manual Eject Hole

33) Turntable Speed Selector

34) Phono on/off LED indicator

35) Phono on/off button

36) Phono cover open switch

37) Tone Arm

38) 45rpm Spindle Adaptor

39) Pick-Up Holder

40) Line Out socket (RCA)

41) Speaker Terminal (L/R)

42) AC Mains Cord

43) FM Wire Antenna

44) Subwoofer-out Jack

E-2

INSTALLATION

Unpack all parts and remove any protective packing materials.

Please keep all packaging until you have fully checked all parts of the unit are working correctly and for future use

in case the unit needs servicing.

Ensure the Remote Control has been taken out of the packaging before storing the box away.

This unit is operated by 230V~50Hz AC mains only.

Do not connect the unit to the mains before checking the mains voltage is correct for the unit and before all other

connections have been made.

When positioning the unit, never cover any vents and make sure that there is a space of several centimeters

around the unit for ventilation.

CONNECTION

1. Connect the speaker wires to the speaker terminals (R + L) (41) located on the

rear of the unit. Push the right red socket switch upwards to expose the hole

in which to insert the red speaker cable –insert the wire and release the switch.

Push down the right black socket switch and insert the black cable wire.

Repeat this process for the other speaker, ensuring only the metal part of the

wire is inserted.

2. Connect the power cord (42) to a 230V AC Mains outlet.

3. ….. ….. : ….. ….. will be flashing on the dimmed LCD Display (1), and the Red

STANDBY LED Indicator (3) will light up, which indicates the unit is

connected to the mains power and the system is ready for use.

4. Switch the unit on with the main On/Off button (4) - the Red standby LED will go off , the display will light up and

show TUNE (FM radio function) first and sound will be coming out from the speakers, which indicates the unit is

correctly connected to the power supply and the system is ready to play your music.

5. Press the Standby/On button (17) to switch the unit on - the LCD display, as well as the blue LED light

around the VOLUME control (21) will light up. “TUNE” shows briefly on the display and sound will be coming

from the speakers.

Note: The unit is defaulted to start with the radio (Tuner) function after switching on.

6. Press the FUNCTION button (18) repeatedly to switch to other functions –on the display it will show:

CD-2 --- BUSY, then CD 1 --- BUSY –PHON –TAPE –AUX and eventually TUNE again.

NOTE: If you find the unit switches itself off regularly, this is not a fault. Due to the ErP stage 2

requirements for the Protection of the Environment when connected to the mains power, as a power saving

measure the unit will switch itself off automatically if no music has been playing for over 15 minutes.

Switch the unit off and then on again to re-activate it.

SETTING THE CLOCK

1. Make sure the unit is in Standby mode (3).

2. Press and hold the “MEM/CLK-ADJ” button (5) a second, the display will start flashing.

3. Press the Skip/TUNE or button (13) to select the appropriate hour format (12hr/24hr).

4. To set the HOUR: Press the “MEM/CLK-ADJ” button again, the first 2 digits will be flashing.

5. Press the Skip/Tuning or button (13) to set the correct hour.

6. Press the ”MEM/CLK-ADJ” button to store the correct hour.

7. To set the MINUTES: The 3rd and 4th digits “00” will then be flashing, press the Skip/Tuning or button

(11) to set the correct Minutes

8. Press “MEM/CLK-ADJ” to store the correct minutes.

LISTENING TO THE RADIO

Manual Tuning

1. Switch the unit on with the MAIN On/Off button (4).

2. Press the FUNCTION button (24) to select “TUNER” mode.

3. Select the desired band with the BAND/ button (11).

4. To tune into the required station press the TUNE down or TUNE up button (11).

5. Rotate the VOLUME knob (10) to adjust the volume level (ranging from “0 –30” –shown on the display).

Auto Tuning

1. Press the FUNCTION button (24) to select “TUNER” mode

2. Select the desired band with the BAND/ button (18).

3. Press and hold the TUNE or button (11) for 1-2 seconds and then release it.

4. The unit will start searching automatically and stop when a radio station has been found.

5. Repeat step 2 until the desired radio station has been reached.

6. Rotate the VOLUME knob (10) to adjust the volume level (ranging from “0 –30” as shown on the display).

E-3

Preset Stations

You can store up to 50 radio stations into memory (FM-30 / (AM) MW-20). To do so, follow the procedure below:

1. Select the Tuner mode with the FUNCTION button (24).

2. Turn to the desired radio station with the “MANUAL” or “AUTO” tuning method as described above.

3. Press the “MEM/CLK-ADJ” button (5) to enable programming and the “MEM” indicator appears on the display.

4. Press the “FOLDER/PRE-UP/DOWN” button (8/9) to select the desired station memory for storage.

5. Press the “MEM/CLK-ADJ” button again to confirm the setting.

6. Repeat steps 2 to 5 above to store other stations.

7. If you wish to return to normal Tuner mode, do not press any keys.

8. You can now select the pre-set stations in the set order by pressing the “PRE –UP/DOWN” (8/9) button.

FM & FM-stereo reception

Press the “Stop ST-MONO.” button (12) repeatedly and the FM programmes will be received in mono or

stereo mode alternately. If stereo signals are weak, it is preferable to receive an FM programme in mono

sound.

If a stereo signal is being received, the Stereo indicator “ ” will appear on the LCD display to show the radio

is now receiving an FM stereo programme.

Hints for best radio reception:

- AM (= MW): The receiver has a built-in AM bar antenna. If AM reception is weak, slightly rotate or

re-positioning of the unit will usually improve the Medium Wave reception.

- FM: The receiver has an FM wire antenna (43) hanging at the rear of the cabinet. This wire should be totally

unravelled and extended for best reception.

TURNTABLE OPERATION

Getting Started

Slide back the Phono Cover OPEN Switch (36) to open the turntable cover - then gently lift up the cover.

Caution: Do not lift the cover too high to avoid damaging the hinge.

Remove the white stylus protector by pulling it gently forward and off the Red Stylus holder.

DO NOT DISCARD THE STYLUS PROTECTOR, ALWAYS REFIT IT after playing a record to avoid damaging

the stylus tip on the rubber turntable mat when the tone arm is stored back on the spindle adaptor.

Notes:

The stylus is a consumable and is not covered by the Warranty.

Lift up the TONE ARM (37) with the Pick-up Holder (39) and move it to the right hand side.

Then lift off and remove the Spindle Adaptor (38) from the unit. If you need to use it when playing a 45rpm

record (‘single’), place it on the Turntable Spindle first. Remove it when playing 33 or 78rpm records.

After playing your records, return the spindle adaptor to the recess (38) for storage and place the Tone Arm on it

to secure it before closing the cover.

PLAYING A RECORD

1. Select “PHONO”function with the Function button (24).

2. Press the Phono On/Off button (35) - the Red Phono LED Indicator (34) will light up.

3. Set the speed selector (33) to the correct position depending on the record to be

played (i.e.33/45/78rpm).

4. Lift the tone arm from the rest and move it to the right away from the turntable

platter –make sure it does not click or the turntable will start rotating.

5. Place the record on the turntable platter [for some 45rpm records you may need to

use the Spindle Adaptor (38)].

6. Click the tone arm slightly to the right - the platter will start rotating.

7. Gently place the tone arm needle on the position where you wish the record to start

playing.

8. Adjust the volume (10) to the desired level.

9. At the end of the record, the platter will keep turning –press the Phono On/Off

button (35) to stop it rotating, then lift and move the tone arm to the right again.

10. Change to another record if required, ensuring the speed selector is set correctly

for the next record to be played.

11. When you have finished playing your record(s), with the tone arm to the right of the

record, remove the record and place the spindle adaptor back in the recess (38).

12. With the Phono Power On/Off button (35) switched to ‘Off’, the Red Phono ‘Power

On’ LED will go off.

13. Always refit the White Stylus Protector and store the tone arm back on the spindle adaptor grooves.

14. Gently close the cover. E-4

LISTENING TO CASSETTE TAPE

General operation

Press the “FUNCTION” button (24) to select and activate the TAPE Mode, the LCD display will show “TAPE”:

Cassette Playback The system will start playback automatically after a pre-recorded cassette tape has been

inserted into the Cassette slot of the unit (see line drawing below for the correct direction in

which to insert the tape).

The “Tape Forward / EJECT “ button (21) will stay at full height position while playing the tape.

Stop and Ejection Press the “Tape Forward / EJECT“ button (21) completely inwards

- the cassette tape will be ejected though the Cassette Door

Cover (22).

The “Tape Forward / Eject“ button will stay at the lowest height position.

Fast forward Press the “TAPE FORWARD / EJECT “ (21) button halfway in during Playback Mode - the tape

will wind in a forward direction. The button will stay at mid-height position.

Slightly press the “Tape Forward / EJECT “ button in again to resume normal playback - the

“Tape Forward / Eject“ button will resume at the highest position while playing.

Notes:

- Make sure the direction is correct when inserting a tape into the cassette slot. Some searching noise will be

heard, this is quite normal.

- The system cannot perform the normal playback function during Fast Forward mode.

- It is strongly recommended the cassette tape is removed from the Cassette Player slot after each use - don’t

leave the cassette tape inside the system when you do not intend to play it.

Cassette Care

Two common causes of trouble experienced when using cassettes are:

1. Tape jamming, leading to uneven speed during playback.

2. Tape entangling, when the tape wraps itself around vital parts of the mechanism.

To avoid these problems occurring, take the following precautions:

a) Check that there are no loose layers of tape visible through the cassette centre window

(see fig. 1).

b) Take up any loose layers (using a pencil or ballpoint pen with hexagonal barrel) before

inserting the cassette (see fig. 2) into the mechanism.

Notes: If the cassette feels tight whilst performing this operation (see fig. 2), the tape may

be jamming due to ridges formed in the winding of the tape (visible through the centre

window). In most cases, these may be removed by fast rewinding of the cassette from

one end to the other, turning it over and repeating this action again.

Do not expose cassettes to direct sunlight, dust or oil, and do not touch the tape surfaces.

Compact Disc Care

To remove a disc from its storage case, press down on the centre of the case and lift the disc out, holding it carefully

by the edges. Fingerprints and dust should be carefully wiped off the disc’s recorded surface with a soft cloth.

Unlike conventional Vinyl or Shellac records, compact discs have no grooves to collect dust and microscopic debris,

so a gentle wipe with a soft, lint-free dry and clean cloth should remove most particles. Wipe in a straight line from

the inside to the outside of the disc. Never use detergents or abrasive cleaners to clean the disc. If necessary,

use a CD cleaning kit. Small dust particles and light stains will have absolutely no effect on sound reproduction

quality. Never fix labels to the surface of compact discs or write on them, except gently with a special CD-R Pen.

E-5

PLAYING A COMPACT DISC/MP3 DISC IN

The system is equipped with two CD players, the function for is described below and all the CD 1 playback

information will show in the top part of the LCD display:

Getting Started

1. Press the Function button (24) to select, “CD 1”and “NO”will appear on the LCD display.

2. Press the “CD 1 Open/Close ” button (14) to open the CD 1 door (30). “OPEN” shows briefly on the display.

3. Place an audio CD with the printed side facing up inside the tray and close the CD 1 door - “CLOS” shows

briefly on the display (or “NO” if no CD has been placed in the tray).

4. The unit will start reading the disc, the LCD display will show the total number of tracks for a second, then

playback will start automatically. On the LCD display the current track number and the track time will show

alternately. (the Folder number and track time will show alternately during playback of an MP3 CD).

CD 1 PLAY / PAUSE MODE /

1. If the CD 1 Play/Pause/BAND button (13) is pressed when the CD 1s not playing, the first track will be

played.

2. If the Play/Pause button (13) is pressed during playback, the music will pause temporarily and the play

indicator “ “ will start flashing on the LCD display.

3. Press the button again to resume normal playback.

4. If the Stop /ST/MO button (12) is pressed during playback, the music will stop playing and the display will

show the total number of tracks on the Disc.

SKIP MODE (SKIP UP / SKIP DOWN )

1. While the CD 1s playing or is paused, press the CD 1 “Skip Up” button (11) to skip to the next track - the

track number will be displayed. It will then play this track or remain paused.

2. Press the CD 1 Skip Down button (11) to go back to the previous track- this will play or remain paused.

PLAYING AN MP3-CD

1. Press the “FOLDER PRE-UP“ button (8), the folder number will go up.

2. Press the CD 1 “Skip up“ or “ Skip down“ (11) button, the track number will change.

3. When the desired track has been selected, press the CD 1 “Play/Pause” /BAND button (13) to start playback.

MP3 Track Format Requirements:

- MP3 Bit rate: 32 kbps ~ 256 kbps.

- The performance of playing an MP3-CD file varies from that of a pre-recorded Audio CD - the quality depends

on the method of recording.

REPEAT / RANDOM MODE

Press the CD 1 PLAY MODE button (6) repeatedly (before or during playback) to play a file, folder (MP3 disc only) or

all files repeatedly or in random order - in the following order:

FOR CD

(1) repeat 1 (2) repeat all tracks (3) random (4) off mode

Indicator

Play mode on LCD display

Repeat track

Repeat all

Random RAN

Off mode --------------

FOR MP3-CD

(1) repeat 1 (2) repeat 1 folder (3) repeat all (4) random (5) off mode

Indicator on USB/SD

Play Mode operation display

Repeat a single track

Repeat single folder

Repeat all tracks

Random mode RAN

Off mode ----------------- E-6

REMOTE CONTROL SECTION (58)

Repeat play

With this function you can listen to a desired file or folder over and over again.

Random play

With this function you can listen to all files in any (random) order.

CD/MP3-CD PROGRAMMING (BY REMOTE CONTROL)

Up to 20 tracks can be programmed for CD (100 tracks for MP3-CD files) using the Remote Control.

Before programming, ensure the system is in Stop mode.

1. Press the FUNCTION button to select CD 1 mode and stop playback .

2. Press the “MEM/CLK-ADJ” button (58), “ MEM “ will appear on the display.

It will also indicate the program number and track number digits for the track

to be programmed.

3. Select a track by pressing the Skip Up TUNE/or Skip Down /TUNE

buttons (58) on the Remote.

4. Press the “MEM/CLK-ADJ” button to store the track into memory.

5. Repeat steps 3 and 4 to enter additional files into the memory if required.

6. When all the desired files have been programmed, press the CD1

Play/Pause button (13) to play the files in the designated order.

7. To cancel the programmed files, press the “CD Stop ” button (12) until

“MEM“ disappears from the display.

PLAYING A COMPACT DISC IN CD2

The playback information for CD2 will appear in the bottom section of the LCD display.

Getting started

1. Press the Function button (24) to select CD 2 mode, the LCD display will show “CD-2 ” then “--- bUSY “for a

second, then change to “NO DISC”.

2. Then press the “CD 2 Open/Close ”button (20) to open the CD 2 door (31).

3. Place an audio CD with the printed side facing up inside the tray and then close the CD tray .

4. The unit will start reading the disc, the display bottom area will show “bUSY“ and then display the total number of

tracks and total playing time of the disc.

Play / Pause mode

1. Press the CD 2 “Play/Pause ” button (19) to start playback, the first track will start playing.

2. To interrupt play, press the CD 2 “Play/Pause ” button once, the playing time will freeze on the LCD display,

press it again to resume normal playback.

Stop mode

If “CD 2 Stop “button (18) is pressed during play or pause mode, the disc in CD 2 will stop playing and show

the total number of tracks on the CD Recorder operation LCD display.

Skip mode (skip up / skip down )

1. While a CD 1s playing or paused, if the “CD 2 Skip up ” button (17) is pressed, it will go to the next track, the

display will show the track number and play it.

2. While a CD 1s playing or paused, if the “CD 2 Skip down ” button (17) is pressed, it will go back to the

previous track and play it.

IMPORTANT NOTES:

When changing a disc, always press the “CD 2 Stop ” button (18) first so that the CD 2 Recorder operation

display shows the original information - before pressing the “CD 2 Open/Close ” button (20)!

- The reaction time of the CD Recorder is longer than that of a normal CD player due to the complexity of the

system.

- If this happens, please disconnect the unit from the mains, let it rest for about 15 minutes and then re-start it.

This should hopefully re-set the unit.

- The reading and playback time of a CD-R(W) disc may vary from brand to brand.

- There may encounter problems caused by the incompatibility of the disc used: recommended brands of

CD-R(W) disc are for instance TDK, Maxell, Sony, Fuji, and other good quality discs.

- This device is only designed for recording to normalAudio CD format - it does not record to MP3/WMA format.

E-7

REPEAT MODE for CD 2 (on the Remote Control only)

Repeat play (by remote control)

Press the repeat/random button before or during playback, a single track or all the tracks

can be played in difference mode as follows:

(1) Repeat all track (2) Repeat 1 (3) Off mode

Indicator on CD/CD Recorder

Play mode operation display area

Repeat all

Repeat 1

Off mode --------------

CD 2 DISC PROGRAMMING (on the Remote Control only)

Up to 32 tracks can be programmed to play in CD 2. Make sure CD 2 is stopped (50) first before starting.

1. Select CD 2 mode (24) and stop the disc from playing (50).

2. Press the CD 2 “PROGRAM” button of CD 2 on the remote control, the “ PROG “ indicator will show on the display.

On the LCD display it will also indicate the program number (P-01) and the digits of the track numbers to be

programmed.

3. Select a desired track by pressing the skip up or down buttons.

4. Press the “ PROGRAM ” button again to store the track into memory.

5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.

6. When all the desired tracks have been programmed, press the CD 2 “Play/Pause ” button to play the disc in

designated order.

7. To cancel the programmed file, press the CD 2 “Stop” (50) button on the remote handset until the

“PROG“indicator has disappeared from LCD display.

Notes:

After playing the programmed songs, it is possible to delete a programmed track after it has started playing, starting

with the last one down to the first one:

1. Press the CD 2 Stop button (50) to make sure the unit is in stop mode first.

2. Press the “CLEAR“ button (57) repeatedly on the remote control –this will delete the programmed tracks one by

one from the memory.

CD 2 RECORDING FUNCTION (from PHONO / AUX / TAPE / CD)

Apart from the CD 2 playback function, this CD 2 Player/ “Burner” can also record to and “burn” a CD, either from CD

1/ Phono/Aux/Tape mode. Note: All recorded tracks will be recorded in AUDIO-CD format.

Before starting this process (for all modes), select CD 2 function (24), press the CD 2 Open/Close button

(20) to open the CD 2 door (31) and place a blank recommended brand CD-R or CD-RW disc* in the tray.

IMPORTANT NOTES –READ BEFORE STARTING RECORDING:

1. It is only possible to record on a blank disc* –to make sure it is, check that after placing it in the CD 2 tray (31),

the “NO TOC“ indicator (= “No Table of Contents”) shows on the LCD display.

2. Before starting recording, please refer to the “TRACK SEPARATION” section in this Instruction Manual for

instructions on how to separate the tracks during recording. [See B ii) in Recording Settings]

3. A “CD-R” disc can be recorded on only once and cannot be erased or re-recorded on.

4. The playback quality of either a CD-R or CD-RW disc varies between different brands of Audio CD player.

5. The revolving speed of the CD 2 Burner is higher than that of a normal CD mechanism, therefore some

mechanical noise and vibration of the unit cabinet may occur during operation. Please note this is not a

malfunction of the system.

6. Due to the variety in the quality and the compatibility of CD-R(W) discs available, please change to another brand

if you find you cannot record on the one used or the performance is not very stable.

HOW TO MANUALLY EJECT A CD FROM CD 2

Due to the complexity of the CD burner mechanism, if the power is interrupted or if you notice a problem occurring

during the CD burning process, the system will be locked and the CD tray may not eject when the CD 2 Open/Close

button (20) is pressed.

If that happens it will be necessary to manually eject the CD tray to retrieve the CD, as follows:

E-8

1. Turn OFF the power to the unit first. Do not manually open the tray when there is power to the drive!

2. Locate the Manual Eject Hole (32) on the front panel below the CD 2 tray, as

indicated by the arrow in the line drawing.

3. Carefully insert a stiff wire (for instance a straightened paper clip) into the CD 2

Manual Eject Hole.

4. When resistance is felt, gently press harder until the drive tray opens slightly.

5. Gently pull the tray out the rest of the way by hand to expose the CD and remove this.

6. Re-connect the unit to the mains and restart the system - then repeat the burning

/recording process again.

A) CD RECORDING MODE

i) CD Recording from Phono

1. Press the Function button (24) to select Phono (record player).

2. Place a vinyl record you wish to record to CD on the turntable and get it ready for playback.

3. Press the “CD 2 “REC“ button (29) and then the CD 2 “Play/Pause ” button (19) to confirm recording until

the play “ “& “ “ indicators show on the CD Recorder operation display.

4. After a few seconds, the CD Recorder display will show the numbers of the Time Counter –recording has now

started.

5. Now start playback of the record (Phono), separating the tracks during recording if required.

6. When the recording has finished, press the “CD 2 Stop ” button (18) and then stop playback of the vinyl

record.

7. Finalize the recorded disc, as described elsewhere in this manual.

ii) CD Recording from Cassette Tape

1. Press the Function button (24) to select TAPE (Cassette Player).

2. Place a pre-recorded cassette tape in the cassette player slot (22), ready to play back the track(s) you wish to

record –but do not push it all the way in yet.

3. Press the “CD 2 REC “ button (29) and then the CD 2 “Play/Pause ” button (19) until the play indicator

“ “shows on the CD Recorder operation display.

4. After a few seconds, the CD Recorder operation display will show the numbers of the Time Counter –recording

has now started.

5. At this point, push the tape into the cassette mechanism to start playback of the track(s) you wish to record.

6. After recording has finished, press the “CD 2 Stop ” button (18)and then stop playback of the cassette tape.

7. Remove the cassette from the player when finished.

8. Finalize the recorded disc if you wish it to play it in another CD Player - as described elsewhere in this manual.

iii) CD Recording from an Audio CD in CD 1

1. Press the Function button (24) to select CD 1 mode.

2. Press the CD 1 “open/close button” (14), open the drawer and insert the pre-recorded Audio CD you wish to

record on a blank CD.

3. Press the “CD 2 REC“ button (29) and then the “CD 2 Play/Pause ” button (19) until the play indicator

“ “ shows on the CD Recorder operation display.

4. After a few seconds, the CD Recorder operation display will show the numbers of the Time Counter - recording

has now started.

5. Now press the “CD 1 Skip up or down button“ (11) to choose the track you wish to record, then press the

“CD 1 Play/Pause ” button (13) to start playback of the track to be recorded.

6. If recording the complete CD, separate the tracks if required.

7. After recording has finished, first press the “CD 1 Stop ” button (12) to stop the CD playing, and then the “CD 2

Stop ” button (18) to stop the recording.

8. “Finalize” the recorded disc if you wish it to play it in another CD Player - as described elsewhere in this manual.

iv) CD Recording from Aux-in

1. Press the Function button (24) to select AUX (external device) mode.

2. Connect another audio device (such as an MP3 player, CD player, DAB Radio, etc.) via its output or headphone

socket, to the 3.5mm dia. Aux-in jack (16) of this unit (use a connecting cable with 3.5mm dia. stereo input plug).

3. Press the “CD 2 “REC“ button (29) and then the CD 2 “Play/Pause ” button (19) to confirm recording until

the play “ “ & “ “ indicators show on the CD Recorder operation display.

4. After a few seconds, the CD Recorder display will show the numbers of the Time Counter - the system has now

started recording.

5. Now start playback of the external device connected to Aux-in, separating the tracks during recording if required.

6. When the recording has finished, press the “CD 2 Stop ” button (18) and then stop playback of the connected

external device (remove it after the recording process has finished).

7. “Finalize” the recorded disc if you wish it to play it in another CD Player as described elsewhere in this manual.

E-9

Inhaltsverzeichnis

Andere Steepletone CD-Player Handbücher

Steepletone

Steepletone GROOVE Bedienungsanleitung

Beliebte CD-Player Handbücher anderer Marken

RCA

RCA RP-7923 Bedienungsanleitung

Pioneer

Pioneer DEH-P3550MP XM Bedienungsanleitung

Philips

Philips AZ1207 Bedienungsanleitung

Philips

Philips CD582 Bedienungsanleitung

Philips

Philips AZ 6821 Bedienungsanleitung

Lasonic

Lasonic MSU-2020 Bedienungsanleitung

THOMSON

THOMSON RCD150 Bedienungsanleitung

Denon

Denon DCD-1420 Bedienungsanleitung

Panasonic

Panasonic SJ-MR100 Bedienungsanleitung

Onkyo

Onkyo DX-7210 Bedienungsanleitung

Sony

Sony MZ-R3 Bedienungsanleitung

Denon

Denon DVM-4800 Bedienungsanleitung

JBL

JBL MR-32 Bedienungsanleitung

RCA

RCA RCD152 Bedienungsanleitung

Technics

Technics SL-PS770A Bedienungsanleitung

Clarion

Clarion compact disc Bedienungsanleitung

Sony

Sony MZ-M10 Bedienungsanleitung

Philips

Philips Expanium AZ 1538 Bedienungsanleitung