Stenner Pumps ECON FP Series Handbuch
TO BE INSTALLED AND MAINTAINED BY PROPERLY TRAINED
PROFESSIONAL INSTALLER ONLY. READ MANUAL & LABELS
FOR ALL SAFETY INFORMATION & INSTRUCTIONS.
WARNING
PERISTALTIC METERING PUMPS SINCE 1957
ECON FP PUMP SER ES
PER STALT C METER NG PUMP
INSTALLATION AND MAINTENANCE MANUAL
2www.stenner.comcon FP
Warranty and Service Policy ................................................................. 3
Safety nstructions ....... cover, 4-6, 9, 15, 17, 20-21, 23, 25-29, 31-34, 36
Materials of Construction .................................................................... 7
Accessories ......................................................................................... 8
Flow Rate Outputs ............................................................................... 9
Modes of Operation Description ........................................................ 10
Control Panel Guide...................................................................... 11-12
Pre-Programming Requirements ................................................... 13-14
Program Pump Settings ................................................................ 15-19
nstallation................................................................................... 20-29
Troubleshooting ............................................................................ 30-32
Tube Replacement ........................................................................ 33-35
Cleaning The Point of njection...................................................... 36-38
Exploded View.................................................................................... 39
Parts ................................................................................................. 40
Mounting Template ............................................................................ 41
IMEFP 052220
TABLE OF CONTENTS
L M TED WARRANTY
Stenner Pump Company will for a period of one (1) year from the date of purchase (proof
of purchase required) repair or replace at our option all defective parts. Stenner is not
responsible for any removal or installation costs. Pump tube assemblies and rubber
components are considered perishable and are not covered in this warranty. Pump tube
will be replaced each time a pump is in for service, unless otherwise specified. The cost of
the pump tube replacement will be the responsibility of the customer. Stenner will incur
shipping costs for warranty products shipped from our factory in Jacksonville, Florida. Any
tampering with major components, chemical damage, faulty wiring, weather conditions,
water damage, power surges, or products not used with reasonable care and maintained in
accordance with the instructions will void the warranty. Stenner limits its liability solely to
the cost of the original product. We make no other warranty expressed or implied.
RETURNS
Stenner offers a 30-day return policy on factory direct purchases. xcept as otherwise
provided, no merchandise will be accepted for return after 30 days from purchase. To
return merchandise at any time, call Stenner at 800.683.2378 for a Return Merchandise
Authorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of your
invoice or packing slip with your return.
DAMAGED OR LOST SH PMENTS
Check your order immediately upon arrival. All damage must be noted on the delivery
receipt. Call Stenner Customer Service at 800.683.2378 for all shortages and damages
within seven (7) days of receipt.
SERV CE & REPA RS
Before returning a pump for warranty or repair, remove chemical from pump tube by
running water through the tube, and then run the pump dry. Following expiration of the
warranty period, Stenner Pump Company will clean and overhaul any Stenner metering
pump for a minimum labor charge plus necessary replacement parts and shipping. All
metering pumps received for overhaul will be restored to their original condition. The
customer will be charged for missing parts unless specific instructions are given. To return
merchandise for repair, call Stenner at 800.683.2378 or 904.641.1666 for a Return
Merchandise Authorization (RMA) number.
D SCLA MER
The information contained in this manual is not intended for specific application purposes.
Stenner Pump Company reserves the right to make changes to prices, products, and
specifications at any time without prior notice.
TRADEMARKS
Santoprene®is a registered trademark of xxon Mobil Corporation.
AquaShield™is a trademark of Houghton International.
3
USA and Canada 800.683.2378, International 904.641.1666 con FP
WARRANTY AND CUSTOMER SERV CE
4www.stenner.comcon FP
MPORTANT SAFETY NSTRUCT ONS
When installing and using this electrical equipment,
basic safety precautions should always be followed,
including the following:
1.READ AND FOLLOW
ALL NSTRUCT ONS.
2.WARN NG - To reduce the risk of
injury, do not permit children to use
this product unless they are closely
supervised at all times.
3.WARN NG - Risk of lectric Shock.
Connect only to a branch circuit
protected by a ground-fault circuit
interrupter (GFCI). Contact a qualified
electrician if you cannot verify that
the receptacle is protected by a GFCI.
4.WARN NG - To reduce the risk of
electric shock, replace damaged
cord immediately.
5.SAVE THESE NSTRUCT ONS.
5
USA and Canada 800.683.2378, International 904.641.1666 con FP
SAFETY NFORMAT ON
Warns about hazards that CAN cause death, serious personal
injury, or property damage if ignored.
ELECTR C SHOCK HAZARD
ELECTR C SHOCK HAZARD:
The pump must only be used with the Class II power supply that is supplied with
the pump.
R SQUE DE CHOC ELECTR QUE:
La pompe ne peut être utilisée qu’avec le bloc d’alimentation de type Classe II
originalement fourni avec celle-ci.
R SK OF ELECTR C SHOCK:
This pump has not been investigated for use in swimming pool or marine areas.
R SQUE DE CHOC ELECTR QUE:
La pompe n’a pas été vérifiée et approuvée pour utilisation sur des applications de
piscine ou autre installation marine.
DO NOT alter the power cord or power supply.
DO NOT use receptacle adapters.
DO NOT use pump with a damaged or altered power cord or power supply. Contact
the factory or an authorized service facility for repair.
HAZARDOUS VOLTAGE:
D SCONNECT power cord before removing motor cover for service. Electrical service
by trained personnel only.
EXPLOS ON HAZARD:
This pump is not explosion proof. DO NOT install or operate in an explosive environment.
R SK OF EXPOSURE:
Potential for burns, fire, explosion, personal injury, or property damage. To reduce risk
of exposure, the use of proper personal protective equipment is mandatory.
R SK OF F RE HAZARD:
DO NOT install or operate on any flammable surface.
R SK OF CHEM CAL OVERDOSE:
To reduce risk, follow proper installation methods and recommendations. Check your
local codes for additional guidelines.
To reduce the risk of injury, do not permit children to use this
product. This appliance is not to be used by persons with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction.
6www.stenner.comcon FP
SAFETY NFORMAT ON continued
Warns about hazards that W LL or CAN cause minor personal
injury or property damage if ignored.
PLUMB NG:
Metering pump installation must always adhere to your local plumbing codes and
requirements. Be sure installation does not constitute a cross connection. Check
local plumbing codes for guidelines.
This pump has been evaluated for use with water only.
NOT CE: ndicates special instructions or general mandatory action.
This metering pump is portable and designed to be removable from the plumbing
system without damage to the connections.
Before installing or servicing the pump, read the pump manual for all safety
information and complete instructions. The pump is designed for installation and
service by properly trained personnel.
Installation and product must adhere to all regulatory and compliance codes
applicable to the area.
This is the safety alert symbol. When displayed in this manual or on the
equipment, look for one of the following signal words alerting you to the
potential for personal injury or property damage.
Acceptable for indoor use; or, outdoor use when mounted as shown in the
Installation Section.
Destiné à une utilisation intérieure ou extérieure lorsqu’il le schéma de la section
installation est respecté.
lectrical installation should adhere to all national and local codes. Consult a licensed
professional for assistance with proper electrical installation.
Removing power from recirculation pump must also remove power from pump.
The use of an auxiliary safety device (not supplied), such as a flow switch or sensor,
is recommended to prevent feed pump operation in the event of a recirculation
pump failure or if flow is not sensed.
Point of injection should be beyond all pumps, filters, and heaters.
Maximum temperature = 40°C
7
USA and Canada 800.683.2378, International 904.641.1666 con FP
MATER ALS OF CONSTRUCT ON
All Housings
Polycarbonate
Pump Tube & Check Valve Duckbill
Santoprene®(FDA approved)
Suction/Discharge Tubing & Ferrules
Polyethylene (FDA approved)
Suction Line Strainer and Cap
PVC or Polypropylene (both NSF listed); ceramic weight
Tube & Injection Fittings
PVC or Polypropylene (both NSF listed)
Connecting Nuts
PVC or Polypropylene (both NSF listed)
All Fasteners
Stainless steel
ACCESSOR ES
Contents
3 Connecting Nuts 1/4"
3 Ferrules 1/4" or 6 mm Europe
1 Duckbill Check Valve
1 Weighted Suction Line Strainer 1/4" or 6 mm Europe
1 20' Roll of Suction/Discharge Tubing
1/4" White or UV Black OR 6 mm White Europe
1 Additional Pump Tube
1 Manual
8www.stenner.comcon FP
9
USA and Canada 800.683.2378, International 904.641.1666 con FP
Item Number Pump Roller Turndown Gallons Gallons Ounces Ounces Pressure
Prefix Tube Assembly Ratio per Day per Hour per Hour per Minute Max. psi
10PLM M White 10:1 0.49 0.02 2.6 0.04 80
10PHM M White 10:1 0.83 0.03 4.4 0.07 80
20PHM M White 10:1 1.41 0.06 7.5 0.13 80
20PHF F White 10:1 4.5 0.19 24.0 0.40 80
20PHG G Black 10:1 16.0 0.67 85.3 1.42 80
20PHH H Black 10:1 30.0 1.25 160.0 2.67 80
NOT CE: The information within this chart is solely intended for use as a guide. The output data is an approximation based on
pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump
Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.
NOT : Duckbill check valve included with pumps rated 80 psi (5.5 bar) maximum.
FLOW RATE OUTPUTS
Item Number Pump Roller Turndown Liters Liters Milliliters Milliliters Pressure
Prefix Tube Assembly Ratio per Day per Hour per Hour per Minute Max. bar
10PLM M White 10:1 1.84 0.08 76.7 1.3 5.5
10PHM M White 10:1 3.14 0.13 130.8 2.2 5.5
20PHM M White 10:1 5.36 0.22 223.2 3.7 5.5
20PHF F White 10:1 17.01 0.71 708.8 11.8 5.5
20PHG G Black 10:1 60.48 2.52 2520.0 42.0 5.5
20PHH H Black 10:1 113.40 4.73 4725.0 78.8 5.5
Approximate Maximum Outputs @ 50/60Hz
Approximate Maximum Outputs @ 50/60Hz
10 www.stenner.comcon FP
MODES OF OPERAT ON DESCR PT ON
The con FP is a flow activated pump and will accept a dry contact signal or a 12-24VAC/VDC
signal from any control equipment that responds to flow. The pump runs at a set time or a
set speed according to the mode of operation selected. The run time or the pump speed is
adjustable from10% to100% in 1% increments. The control panel displays the modes of
operation as SECONDS, AUX L ARY and FLOW SW TCH.
Before programming, review the pre-programming requirements pages 13 to 14, steps A-D.
In the Seconds mode, the pump can receive a dry (non-voltage) contact signal and will run
for a set time in response to receiving the signal. The pump can receive the signal from, for
example,a water meter or control valve that sends a dry contact signal. There is a choice of
five pump operating time ranges and the maximum time is displayed in the control panel;
the run time is adjustable from 10% to 100% in 1% increments.
1 S COND = 0.1 to 1.0
5 S CONDS = 0.5 to 5.0
10 S CONDS = 1.0 to 10.0
20 S CONDS = 2.0 to 20.0
60 S CONDS = 6.0 to 60.0
In the Auxiliary mode, the pump can accept a 12-24VAC/VDC signal and will run at a set
speed for as long as it receives the signal. The pump speed is adjustable from 10% to
100% in 1% increments. If polarity is reversed when connecting a DC signal to the AUX
input, the pump will not respond to the signal. The pump can receive the signal from a
control valve or another type of control equipment that responds to flow.
In the Flow Switch mode, the pump will accept a dry (non-voltage) contact signal from a
2 wire flow switch and will run at the set speed for as long as it receives the dry contact.
The pump speed is adjustable from 10% to 100% in 1% increments. The connection is not
polarity sensitive (polarity is not an issue when connecting the flow switch wires).
SECONDS (dry contact signal)
AUX L ARY (12-24VAC/VDC signal)
FLOW SW TCH (dry contact signal)
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
Andere Stenner Pumps Wasserpumpe Handbücher
Stenner Pumps
Stenner Pumps S Series Handbuch
Stenner Pumps
Stenner Pumps S Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps S Series Handbuch
Stenner Pumps
Stenner Pumps ECON T Series Handbuch
Stenner Pumps
Stenner Pumps SVP Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps E10T1F Handbuch
Stenner Pumps
Stenner Pumps M128 Series Installationshandbuch
Stenner Pumps
Stenner Pumps S10P Series Handbuch
Stenner Pumps
Stenner Pumps M128 Series Handbuch
Stenner Pumps
Stenner Pumps Classic Series Handbuch
Stenner Pumps
Stenner Pumps QuickPro Classic Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps QuickPro Classic Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps SVP Series Handbuch
Stenner Pumps
Stenner Pumps QuickPro Bedienungsanleitung
Stenner Pumps
Stenner Pumps ECON LD Handbuch
Stenner Pumps
Stenner Pumps Classic Series Handbuch
Stenner Pumps
Stenner Pumps 45MHP2 Series Handbuch
Stenner Pumps
Stenner Pumps Classic Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps S Series Bedienungsanleitung
Stenner Pumps
Stenner Pumps SVP4L1 Handbuch
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung