STI UB-1PN Bedienungsanleitung

ADA

for operation

UB-1PN Uni ersal

Pneumatic Button

We protect the things that protect you.

- 2 -

NOTES

It is important to read, understand and follow all instructions provided with this

product. It is the installer’s responsibility to comply with NFPA 70 & 101, NEC,

mounting specifications according to ADA and other applicable electrical

codes. To avoid electrical shock, DO NOT attempt to install this product when

power is on. ADA mounting compliance requires the operable part of the

initiating device shall not be less than 3 1/2 ft. (1.1m ) or greater than 4 1/2 ft.

(1.37m) above finished floor surface. After installation and testing are complete,

provide a copy of this manual to all personnel responsible for testing and

maintenance of this product.

* For access control installations, power for the UB-1PN must be supplied by a

power source Listed to UL294. When used for access control, this device shall

be used as a part of an access controlled egress door system. It is up to the

local AHJ to allow use of this device in place of an automatic sensor. For higher

security installations, lower time limits should be used.

SWITCH RATING Independent Form “Z” contacts

Rated at: 10A @ 240 VAC

Operating Temp: 15° to 120°F (-9° to 49°C)

1,000,000 Cycles

4.83 in.

(123mm)

3.22 in.

(82mm) .91 in.

(23mm)

1.47 in.

(38mm)

- 3 -

1. Choose button message and color. If same as existing, proceed to

2. If choosing a new message, remove button. On the back side of the plate,

squeeze tabs and push actuator assembly into plate just enough to grasp the

button and remove.

3. From the front of the plate, push actuator back into original position.

4. Choose button message. Blank plate is available for your custom message.

a. Insert button message, align 4 notches on actuator.

b. Select color lens. Align top and bottom notches with tabs on

actuator and push until it snaps together.

TO CHANGE BUTTON COLOR AND ROUND MESSAGE

CHANGE TOP MESSAGE

1. Remove LED circuit board.

2. Remove current message by pushing in and

down on tabs 1 and 2 with a small

screwdriver. If necessary, also push in and

down on tabs 3 and 4. Once message is loose,

remove from the front of the plate.

3. Select new message and snap into place.

Blank plates are included to create your own

custom message.

DIFFUSER

BUT

SCREWDRIVER

BUT

BUTTON ACTIVATED

UB-1L LED PCB

NYLON WASHER

SCREW

SQUEEZE TABS

AND PUSH

ASSEMBLY

INTO PLATE

POWERIN

12-30VDC/VAC

- 4 -

INSTALL

To attach, align tabs (as shown)

and gently snap top, then bottom.

Be sure to hear BOTH tabs snap

into place. Contacts can be rotated

180° if desired.

INSTALL OR REMOVE CONTACT BLOCK

REMOVE

To remove, use a

small flat blade

screwdriver.

Position screwdriver

blade under tab and

gently rotate

screwdriver until tab

disengages. Repeat

for opposite tab.

POWERIN

12-30VDC/VAC

BUTTON ACTIVATED

POWER IN

12-30 VDC/VAC

BUTTON ACTIVATED

POWER IN

12-30 VDC/VAC

BUTTON ACTIVATED

CONTACT INFORMATION

CONTACT REMOVAL

DETAIL A

- 5 -

ATTACH POWER FOR LED (IF DESIRED)

(See drawing)

BUTTON ACTIVATED

OFF

MAG LOCK

NC CONTACTS

NO CONTACTS

UB-1L LED PCB

UL Listed

12-24 VDC Power Supply

NORMAL POSITION BUTTON ACTIVATED

OFF

MAGNETIC LOCK

MESSAGE LAMP

BUTTON ACTIVATED

(BLACK) NC

(RED) NO

NC (GREEN)

NO (WHITE)

BUTTON ACTIVATED

CONTACT DIAGRAM

CONTACTS

One set NO nd one set NC

- 6 -

COUNTERCLOCKWISE

CLOCKWISE

TIMER RANGE ADJUSTMENT SCREW

ADJUSTMENT RANGE - 2 TO 60 SECONDS

TIMER FACTORY SET TO MINIMUM TIME

SETTING. TO INCREASE TIME, TURN

SCREW CLOCKWISE IN 1/4 TURN

INCREMENTS. WHEN CLOSE TO DESIRED

TIME, TURN SCREW IN VERY FINE

INCREMENTS TO DESIRED SETTING.

CAUTION: OVER-TIGHTENING MAY

CAUSE DAMAGE TO TIMER.

SWITCH INFORMATION

MOUNT BUTTON ONTO

ELECTRICAL BOX

BUTTON ACTIVATED

CUSTOM LABELS

To create your own custom label, size to fit in .48h x 2.23w as

shown below.

Also available online at: www.sti-usa.com/ublabel

2.23 in.

.48 in.

- 7 -

CONTACT BLOC

COLOR MATCH BAC BOX IT

CUSTOM LABEL APPLIED TO BLAN

MESSAGE PLATES

24 VOLT LED

WHITE (STANDARD)

RED

BLUE

GREEN

12 VOLT LED

RED

BLUE

GREEN

COVERS

BOPPER STOPPER

UNIVERSAL STOPPER

STOPPER II

SUB-UB-1PNC

SUB-71100A-COLOR

(red, blue, green, white or yellow)

UB-1CL-COLOR

(blue, green, white or yellow)

KIT-E10147

KIT-E10145

KIT-E10141

KIT-E10143

KIT-E10144

KIT-E10140

KIT-E10142

STI-6518

STI-13000 Series

STI-1100 Series

ACCESSORIES

DESCRIPTION PART #

See website for complete cover details

2306 Airport Rd • Waterford, MI 48327

Phone: 248-673-9898 • Fax: 248-673-1246

[email protected] • www.sti-usa.com

Taylor House • 34 Sherwood Road • Bromsgrove

Worcestershire • B60 3DR • England

Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999

E-mail: [email protected] • Web: www.sti-emea.com

Inst. Sht. UB-1PN Button JUN2018

WARRANTY

Three year guarantee against breakage of polycarbonate in normal use

(one year on electro mechanical and electronic components).

Electronic warranty form at www.sti-usa.com/wc14.

USA - Headquarters

Inhaltsverzeichnis

Andere STI Sicherheitsausrüstung Handbücher

STI

STI STI-7534 Bedienungsanleitung

STI

STI STI-7532 Bedienungsanleitung

STI

STI SA5600 Bedienungsanleitung

STI

STI Omron BeamSafe II Bedienungsanleitung

STI

STI STI-7524 Bedienungsanleitung

STI

STI STI-13000 Series Merkblatt

STI

STI ValuScan VS6500 Series Bedienungsanleitung

STI

STI STI 6400 Bedienungsanleitung

STI

STI Stopper Station Series Kurzanleitung

STI

STI Stopper II Series Bedienungsanleitung

STI

STI STOPPER SS2 0 Series Bedienungsanleitung

STI

STI OMRON F3SG RR Series Bedienungsanleitung

STI

STI STI-7554 Bedienungsanleitung

STI

STI UB-1TF Bedienungsanleitung

STI

STI Omron F3SG-RA Series Bedienungsanleitung

STI

STI Air-Lock Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung