STIEBEL ELTRON HSBC 300 cool Technisches Datenblatt

OPERATION AND INSTALLATION

Integral cylinder

» HSBC 300 cool (GB) (WPM)

2| HSBC 300 cool www.stiebel-eltron.com

CONTENTS

SPECIAL INFORMATION

OPERATION

1. General information ��3

1.1 Relevant documents_____________________________________________ 3

1.2 Safety instructions_______________________________________________ 3

1.3 Other symbols in this documentation _______________________ 4

1.4 Information on the appliance _________________________________ 4

1.5 Units of measurement __________________________________________ 4

2. Safety��4

2.1 Intended use______________________________________________________ 4

2.2 General safety instructions ____________________________________ 4

2.3 Test symbols ______________________________________________________ 4

3. Appliance compatibility ��5

4. Appliance description ��5

5. Cleaning, care and maintenance ��5

6. Troubleshooting ��5

INSTALLATION

7. Safety��6

7.1 General safety instructions ____________________________________ 6

7.2 Instructions, standards and regulations ____________________ 6

8. Appliance description ��6

8.1 Standard delivery________________________________________________ 6

8.2 Accessories________________________________________________________ 6

9. Preparation ��6

9.1 Installation site___________________________________________________ 6

9.2 Transport and handling ________________________________________ 7

10. Installation�� 12

10.1 Positioning the appliance _____________________________________ 12

10.2 Heating water connection_____________________________________ 12

10.3 DHW connection and safety assembly______________________ 14

10.4 Filling the system_______________________________________________ 15

10.5 Venting the appliance__________________________________________ 16

11. Electrical connection�� 16

11.1 Control voltage __________________________________________________ 17

11.2 Safety extra low voltage_______________________________________ 17

11.3 Heat pump manager terminal assignment ________________ 17

11.4 Accessories_______________________________________________________ 18

11.5 Sensor installation______________________________________________ 19

11.6 Remote control__________________________________________________ 19

12. Commissioning �� 19

12.1 Checks before commissioning the heat pump manager 19

12.2 Commissioning the heat pump manager __________________ 19

13. Settings �� 20

13.1 Wilo-Para .../Sc circulation pumps__________________________ 20

14. Appliance handover�� 21

15. Shutting down the system �� 21

16. Maintenance �� 21

17. Speciﬁcation �� 22

17.1 Dimensions and connections_________________________________ 22

17.2 Hydraulic diagram______________________________________________ 24

17.3 Wiring diagram _________________________________________________ 26

17.4 Sample installation_____________________________________________ 29

17.5 Energy consumption data_____________________________________ 29

17.6 Data table ________________________________________________________ 29

17.7 Accessories_______________________________________________________ 30

GUARANTEE

ENVIRONMENT AND RECYCLING

SPECIAL INFORMATION

General information

www.stiebel-eltron.com HSBC 300 cool | 3

SPECIAL INFORMATION

- The appliance may be used by children over 8

years of age and persons with reduced physi-

cal, sensory or mental capabilities or a lack of

experience and expertise, provided that they

are supervised or they have been instructed

on how to use the appliance safely and have

understood the potential risks. Children must

never play with the appliance. Cleaning and

user maintenance must not be carried out by

children without supervision.

- The connection to the power supply must

be in the form of a permanent connection.

Ensure the appliance can be separated from

the power supply by an isolator that discon-

nects all poles with at least 3mm contact

separation.

- Observe all applicable national and regional

regulations and instructions.

- Observe minimum distances (see chapter "In-

stallation/ Preparations/ Installation site").

- Only a qualiﬁed contractor should carry out

installation, commissioning, maintenance and

repair of the appliance.

DHW cylinder

- Drain the appliance as described in chapter

"Installation/ Maintenance/ Draining the

DHW cylinder".

- Observe the maximum permissible pressure

(see chapter "Installation/ Speciﬁcation/ Data

table").

- The DHW cylinder is under supply pressure.

During the heat-up process, expansion water

will drip from the safety valve.

- The safety valve drain aperture must remain

open to atmosphere.

OPERATION

1. General information

The chapters "Special information" and "Operation" are intended

for appliance users and qualiﬁed contractors.

The chapter "Installation" is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on these instructions to a new user if required.

1.1 Relevant documents

Instructions for the WPM heat pump manager

Operating and installation instructions for the connected

heat pump

Operating and installation instructions for all other sys-

tem components

1.2 Safety instructions

1.2.1 Structure of safety instructions

KEYWORD Type of risk

Here, possible consequences are listed that may result

from failure to observe the safety instructions.

f Steps to prevent the risk are listed.

1.2.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.2.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in non-seri-

ous or minor injury.

OPERATION

Safety

4| HSBC 300 cool www.stiebel-eltron.com

1.3 Other symbols in this documentation

Note

General information is identiﬁed by the adjacent symbol.

f Read these texts carefully.

Symbol Meaning

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

Appliance disposal

f This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.4 Information on the appliance

Connections

Symbol Meaning

Inlet/ intake

Red arrow: hot

Blue arrow: Cold

Green arrow: Neutral

Drain/ outlet

Red arrow: hot

Blue arrow: Cold

Green arrow: Neutral

Domestic hot water

DHW circulation

Heat pump

Heating

1.5 Units of measurement

Note

All measurements are given in mm unless stated oth-

erwise.

2. Safety

2.1 Intended use

This appliance is intended to be used for seasonal heating and

cooling of interiors (7°C/ 12°C) and for DHW heating.

The appliance is intended for domestic use. It can be used safely

by untrained persons. The appliance can also be used in non-do-

mestic environments, e.g.in small businesses, as long as it is

used in the same way.

Any other use beyond that described shall be deemed inappro-

priate. Observation of these instructions and of the instructions

for any accessories used is also part of the correct use of this

appliance.

2.2 General safety instructions

WARNING Burns

There is a risk of scalding at outlet temperatures in ex-

cess of 43°C.

WARNING Injury

The appliance may be used by children over 8 years of

age and persons with reduced physical, sensory or men-

tal capabilities or a lack of experience and expertise,

provided that they are supervised or they have been

instructed on how to use the appliance safely and have

understood the potential risks. Children must never play

with the appliance. Cleaning and user maintenance must

not be carried out by children without supervision.

WARNING Injury

For safety reasons, only operate the appliance with the

front casing closed.

Material losses

The system's active frost protection is not guaranteed if

the power supply is interrupted.

f Never interrupt the power supply even outside the

heating season.

Note

The DHW cylinder is under supply pressure. During the

heat-up process, expansion water will drip from the safe-

ty valve.

f If water continues to drip when heating is complet-

ed, please inform your qualiﬁed contractor.

2.3 Test symbols

See type plate on the appliance.

OPERATION

Appliance compatibility

www.stiebel-eltron.com HSBC 300 cool | 5

3. Appliance compatibility

The appliance can be operated in conjunction with the following

air source heat pumps:

- HPA-O 05.1-07.1 CS Premium

- HPA-O 7-13 (C)(S) Premium

- WPL-A 05-07 HK 230 Premium

- WPL 15-25 A(C)(S)

- WPL 19-24 I, A

4. Appliance description

The buffer cylinder and DHW cylinder with indirect coil are ar-

ranged one above the other and can be separated for easier han-

dling.

The appliance has a plastic jacket with foam insulation and is

equipped with a removable front casing. The appliance is connect-

ed hydraulically and electrically to the heat pump. All hydraulic

connections are made at the top (heating) and rear (DHW).

In addition to the DHW cylinder and the buffer cylinder, further

system components are integrated:

- Heat pump manager

- Highly efﬁcient circulation pump for a heating circuit without

mixer

- 3/2-way diverter valve

- Cylinder primary pump

DHW cylinder

The steel cylinder is coated on the inside with special direct enam-

el and is equipped with a signal anode. The anode with consump-

tion indicator protects the cylinder interior from corrosion.

The heating water heated by the heat pump is pumped through an

indirect coil inside the DHW cylinder. The heat channelled through

the indirect coil is thus transferred to the domestic hot water. The

integral heat pump manager regulates the DHW heating to the

required temperature.

Buffer cylinder

The steel cylinder provides hydraulic separation between the ﬂow

rates of heat pump and heating circuit. The heating water heated

by the heat pump is transferred into the buffer cylinder by the

cylinder charging pump. When a demand is issued, the integral

heating circuit pump delivers the heating water to the heating

circuit.

Heat pump manager (WPM)

The system is controlled by means of the integral heat pump man-

ager.

Note

The heat pump manager has an automatic summer/win-

ter changeover so you can leave the system switched on

in summer.

f Please observe the instructions for the heat pump manager.

5. Cleaning, care and maintenance

f Have the electrical safety of the appliance and the function

of the safety assembly regularly checked by a qualiﬁed

contractor.

f Never use abrasive or corrosive cleaning agents. A damp

cloth is sufﬁcient for cleaning the unit.

Signal anode with consumption indicator

Material losses

If the consumption indicator changes colour from white

to red, have the signal anode checked by a qualiﬁed con-

tractor and if necessary replaced.

D0000103388

1 White = Anode OK

2 Red = Requires checking by qualiﬁed contractor

6. Troubleshooting

Problem Cause Remedy

The water does not heat

up. The heating does not

work.

There is no power.

Check the fuses/ MCBs in

your fuse box/ distribu-

tion board.

If you cannot remedy the fault, contact your qualiﬁed contractor.

To facilitate and speed up your enquiry, please provide the serial

number from the type plate (000000-0000-000000).

No.: 000000-0000-000000

Made in Germany

D0000102540

INSTALLATION

Safety

6| HSBC 300 cool www.stiebel-eltron.com

INSTALLATION

7. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational reliability

only if original accessories and spare parts intended for the unit

are used.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

8. Appliance description

8.1 Standard delivery

The following are delivered with the appliance:

- 4x Adjustable foot

- 1x Outside temperature sensor AF PT

- 1x expansion vessel (incl. fastening material)

- 1x installation kit (pressure reducing valve, check

valves, expansion relief valve, tundish)

8.2 Accessories

8.2.1 Required accessories

Safety assemblies and pressure reducing valves are available

to suit the prevailing supply pressure. These type-tested safety

assemblies protect the appliance against impermissible excess

pressure.

Required for area cooling:

- Pt1000 temperature sensor

- FET remote control

8.2.2 Additional accessories

- Pump assembly for a heating circuit with mixer HSBC3-HKM

- Pipe assembly RBS-SBC

- Pressure hoses

- Water softening ﬁtting HZEA

- Temperature sensor for cooling

- Remote control for heating operation

- STB-FB high limit safety cut-out for underﬂoor heating

systems

Pipe assembly RBS-SBC

The hydraulic connections can be routed upwards at the rear of

the DHW cylinder using the RBS-SBC pipe assembly available as

an accessory.

9. Preparation

9.1 Installation site

Material losses

Never install the appliance in wet rooms.

Install the appliance near the draw-off point in a dry room free

from the risk of frost. To reduce line losses, keep the distance short

between the appliance and the heat pump.

Ensure the ﬂoor has sufﬁcient load bearing capacity and evenness

(for weight, see chapter "Speciﬁcation/ Data table").

The room must not be subject to a risk of explosions arising from

dust, gases or vapours.

If you are installing the appliance in a boiler room together with

other heating equipment, ensure that the operation of the other

heating equipment will not be impaired.

Minimum clearances

≥250 ≥250

≥800

≥100

≥500

≥100

≥500

D0000103389

The minimum side clearances can be swapped between left and

right.

INSTALLATION

Preparation

www.stiebel-eltron.com HSBC 300 cool | 7

9.2 Transport and handling

Material losses

Store and transport the appliance at temperatures be-

tween -20°C and +60°C.

Handling

f Undo the 4screws from the non-returnable pallet.

D0000055519

f Tilt the appliance and screw the 4adjustable feet into the

appliance.

f Lift the appliance off the pallet. For a better hold during

transport, use the recessed grips on the underside and rear

of the appliance.

If narrow doors or hallways hinder handling, you can separate

the upper and lower sections of the appliance as described in the

following chapters.

9.2.1 Removing/ﬁtting the front casing

Removing the front casing

D0000103402

f Remove the 2locking screws on the top of the front casing.

f Unhook the front casing towards the top.

f AA01-X1.18: If required, disconnect the connector plug of the

programming unit from the connection in the appliance. The

functionality of the appliance will not be affected. However,

it will not be possible to operate the appliance via the pro-

gramming unit.

f Remove the earth cable from the front casing.

Fitting the front casing

f Fit the front casing in reverse order.

INSTALLATION

Preparation

8| HSBC 300 cool www.stiebel-eltron.com

9.2.2 Overview of insulation segments

D0000103403

2 3 4

1 Insulation segment1

2 Insulation segment2

3 Insulation material screw

4 Insulation segment3

INSTALLATION

Preparation

www.stiebel-eltron.com HSBC 300 cool | 9

9.2.3 Separating/ joining the appliance sections

Separating the appliance sections

Material losses

Unscrewing the fastening screws destroys the threads in

the insulation segment.

f To open the 3 ﬁxing tabs, loosen the fastening

screws slightly but do not unscrew them completely.

D0000103404

Note

To make removal simpler, the insulation segments have

labelled recessed grips on the left and right.

D0000103405

f Remove insulation segment1.

f Remove insulation segment2.

D0000080287

f Pull the "heating sensor" out of the buffer cylinder.

D0000080288

f Release the sensor lead from the guide groove in the insula-

tion segment.

D0000080289

f Disconnect the push-ﬁt connectors of the 4hydraulic con-

nections. To do this, pull the spring clips fully out with a

screwdriver.

f Pull the hydraulic connectors as indicated.

INSTALLATION

Preparation

10 | HSBC 300 cool www.stiebel-eltron.com

D0000080293

f Remove the 4hydraulic hoses.

f Remove the 2insulation material screws.

f Remove insulation segment3.

D0000103411

f Undo the 2 locking screws on the side proﬁle strips.

f Lift up and unhook the side proﬁle strips.

D0000080343

f Release the 4screws on the tabs at the front of the appliance.

D0000074613

f Pull the upper section of the appliance towards the front.

D0000080345

1 Handle

f Tip the upper section of the appliance backwards. Use the

handle for improved grip.

D0000103412

f Place the upper section of the appliance on a base to prevent

damage.

Andere Handbücher für HSBC 300 cool

Inhaltsverzeichnis

Andere STIEBEL ELTRON Kessel Handbücher

STIEBEL ELTRON

STIEBEL ELTRON HSBC 200 L Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHF 13 C Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON SH 30 S Kurzanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 751 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 300 Trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHO AC 600 7,5 Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON SHD 30 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HydroShark 199LP Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HydroShark 115NG Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU 5 SL antitropf comfort Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON SBB 401 WP SOL Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 302 WP Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 751 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON EBK 5 G Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 50 A Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBP 100 classic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Hydro-Shark SH3-07 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HSBC 200 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HOT 2.6 N Premium Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HydroShark 120NG Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SBB 300 WP Trend Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU HOT Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHW 200 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON EVS15 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung