STM DD210 Bedienungsanleitung

PORTABLE DIESEL TANK 200LTR 12V

MODEL NO: DD210

Thank you for purchasing a STM product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

WARNING! this tank must ONLY be used for diesel fuel.

9Place the tank on a flat surface before filling.

9Secure the tank to strong points with ratchet straps before transporting in or on a vehicle.

9Maintain the pump in good condition (use an authorised service agent).

9Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.

9Keep the pump clean for best and safest performance.

9Ensure the power supply (vehicle battery) corresponds with the requirements of the pump (12V DC).

9Disconnect from battery when not in use.

9Wear protective gloves, and protective clothing when working around fuel.

9Keep children and unauthorised persons away from the working area.

8DO NOT place the tank near any heat source.

8DO NOT start or stop the pump by connecting or disconnecting the battery

clamps.

8DO NOT allow the unit to get wet.

8DO NOT operate the pump with wet hands.

8DO NOT use the pump where explosive or flammable vapours may be

present.

8DO NOT tamper with the pump connections.

2. INTRODUCTION

Manufactured from HDPE for the safe transportation and dispensing of diesel

fuel when supplying on site equipment. Complies to ADR 1.1.3.1.C for exemption

from requirements of ADR regulations. Supplied with a 12V electric pump, 4mtr

electric cable and clamps and a 4mtr delivery hose with automatic fuel nozzle.

Can be safely secured and transported on a pick-up truck or van, using grooves

for tie-down straps and 6 handles for positioning. Supplied with lockable cover.

Not suitable for petrol.

3. SPECIFICATION

Refer to

instructions Wear protective

gloves Wear protective

clothing

Model No:............................. DD210

Voltage:. ................................. 12V

Current:. ..................................15A

Power: .................................180W

Tank Capacity: ........................... 200ltr

Flow Rate: ............................20ltr/min

Duty Cycle: ................. 30mins on/30mins off

Dimensions (W x D x H): .......1100 x 800 x 470mm

Nett Weight: ........................... 30.42kg

Key: (fig.1. & fig.1A).

1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Breather Lid

2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pump On/Off Switch

3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Clips

4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic Fluid Nozzle

5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Securing Strap Locations

6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Vent Plug

7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Fork Locations

8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Moulded Hand Holds

Wear safety

footwear

g.1

g.1A

4. OPERATION

4.1. TRANSPORT

4.1.1. Movetheemptytankassemblywithtwopersonsusingthehandholdsmouldedintothebaseoftheunit(g.1A.8).

4.1.2. Movebyforklifttruckusingtheforklocationsshownin(g.1A.7).Ensurethattheller(g.1A.1)isclosedbeforemoving.

4.1.3. Securethetanktothecarryingvehiclebyratchetstraps.Locationsforthestrapsaremouldedintothetank(g.1A.5).

4.2. FILLING

4.2.1. DO NOT run the pump without fuel in the tank. To do so will damage the pump’s internal components and will invalidate your warranty.

4.2.2. Thetankislledbyunscrewingtheller(g.1.1)inananticlockwisedirection.Retthellercapimmediatelyafterlling.

WARNING takecarenottooverllthetank.

4.3. FUEL DISPENSING

4.3.1. Beforeconnectingtoabattery,makesurethatthepumpswitch(g.5.2)isinthe‘off’(O) position. Connect the battery clips to the

12V battery, observing correct polarity (red clamp to +ve terminal, black clamp to -ve terminal)

4.3.2. Switchthepumpswitchtothe‘on’(I) position.

4.3.3. Unwindsufcienthoseandplacethenozzle(g.4)inthereceivingtankandpullthetrigger(g.4).Deliverywillcommenceand 

continue until the trigger is released.

4.3.4. Thetriggercanbelockedinoneofthreepositionsbyengagingthelatch(g.4)toholdthetriggeropen.DO NOT leave the nozzle

unattended with the trigger latched open.

4.3.5. Slight pressure on the trigger will release the latch.

4.3.6. When the level in the receiving tank reaches the nozzle, delivery will stop automatically.

4.3.7. When delivery is complete, switch off the pump. Ensure the hose is wound into its housing on the tank and that the nozzle is

secured in its storage place.

4.3.8. DO NOT operate the pump continuously for more than 30 minutes. The duty cycle of the unit is 30 minutes, after which the motor must

be left to cool down for a further 30 minutes.

4.3.9. DO NOT run the unit for more than 2-3 minutes with the delivery nozzle closed.

5. MAINTENANCE

5.1. The pump contains no user-servicable parts.

Repairs should only be undertaken by competent

persons.

5.2. Check the integrity of all the hose connections

periodically. If any leakage is evident, strip the

joint and wind PTFE tape around the male thread.

5.3. Check all electrical connections and cables for wear

and damage. Rectify any faults found.

5.4. Keep clean, especially the dispenser nozzle.

5.5. Clean with a damp, soapy cloth.

5.6. DO NOT use abrasive or solvent cleaners.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

g.3

g.5

g.4

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.