Stratasys Objet Series Leitfaden

Caution—

To avoid exposure to skin irritants,

wear protective gloves (provided)

throughout this procedure.

DOC-34032 Rev. A

B. Remove screws B.

C. Loosen screw C.

A. Put on protective gloves. Remove the print block cover.

A. Remove the Support print head card.

B. Loosen the print head thumb screws.

Removing the Support Print Head

Support Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 1

While holding the print head, press down

on the thumb screws and remove it.

DOC-34032 Rev. A

5Make sure you remove the two O-ring

seals along with the print head.

6Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Install the print block cover.

Push on the tab and then pull the jig

downwards to remove it.

DOC-34032 Page 2

Rev. A

Tighten the print head thumb screws.

Press down firmly on the Support print

head card to attach it to the print block.

Installing the Support Print Head

FRONT

PUSH

FIRST

With the print head in the positioning jig,

align it as shown.

Make sure the O-ring seals

are installed on the print head.

FRONT

Remove

Push tab

A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

A. Insert and tighten screws A.

B. Tighten screw B.

Make sure that the Model head is installed as described in Model Print Head Replacement.

Remove the Model print head card.

Removing the Model Print Head

Model Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 3

B. Loosen the print head thumb screws.

DOC-34032 Rev. A

Make sure you remove the two O-ring

seals along with the print head.

2While holding the print head, press down

on the thumb screws and remove it.

To replace the Model print head, you must first remove the Support print head

(see page 1).

Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Installing the Model Print Head

Page 4

DOC-34032 Rev. A

After you replace the Model print-head, re-install the Support head (see page 2).

Push on the tab and then pull the jig

downwards to remove it.

Tighten the print head thumb screws.

Press down firmly on the Model print

head card to attach it to the print block.

FRONT

PUSH

FIRST

Make sure the O-ring seals

are installed on the print head.

FRONT

With the print head in the positioning jig,

align it as shown.

3A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

FRONT

Remove

Push tab

Andere Stratasys 3D-Drucker Handbücher

Stratasys

Stratasys Fortus 250mc Bedienungsanleitung

Stratasys

Stratasys Origin One Bedienungsanleitung

Stratasys

Stratasys Objet30 Bedienungsanleitung

Stratasys

Stratasys F770 Bedienungsanleitung

Stratasys

Stratasys Objet1000 Connex 2 Bedienungsanleitung

Stratasys

Stratasys Fortus 360mc Bedienungsanleitung

Stratasys

Stratasys V650 Flex Betriebsanleitung

Stratasys

Stratasys Prodigy Plus Bedienungsanleitung

Stratasys

Stratasys Eden250 Bedienungsanleitung

Stratasys

Stratasys Fortus 360mc Bedienungsanleitung

Stratasys

Stratasys Eden260V Bedienungsanleitung

Stratasys

Stratasys Fortus 900mc Bedienungsanleitung

Stratasys

Stratasys Connex500/350 Bedienungsanleitung

Stratasys

Stratasys F770 Betriebsanleitung

Stratasys

Stratasys K6 Series Bedienungsanleitung

Stratasys

Stratasys Neo 450 Bedienungsanleitung

Stratasys

Stratasys Fortus 380mc Bedienungsanleitung

Stratasys

Stratasys J826 Bedienungsanleitung

Stratasys

Stratasys J5 Series Bedienungsanleitung

Stratasys

Stratasys F123 Series Bedienungsanleitung

Stratasys

Stratasys Fortus 900mc Referenzhandbuch

Stratasys

Stratasys Objet350 Bedienungsanleitung

Stratasys

Stratasys Fortus 360mc Betriebsanleitung

Stratasys

Stratasys Objet500 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung

German RepRap

German RepRap X400 Pro V3 Bedienungsanleitung