Sub-Zero UC-15I Bedienungsanleitung

Undercounter Ice Machine Installation Guide

UNDERCOUNTER ICE MACHINE

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

Sub-Zero Customer Care 800.222.7820

Contents

3Undercounter Ice Machine

4Opening Dimensions

5Electrical

6Plumbing

7Installation

10 Custom Panel

11 Completion

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

subzero.com

Product Information

Important product information including the model and

serial number are listed on the product rating plate. The

rating plate is located in the upper left corner of the ice

storage bin, on the back of the unit. Refer to the illustration

below.

If service is necessary, contact Sub-Zero factory certied

service with the model and serial number. For the name

of the nearest Sub-Zero factory certied service or for

questions regarding the installation, visit the contact & sup-

port section of our website, subzero.com or call Sub-Zero

customer care at 800-222-7820.

UNDERCOUNTER ICE MACHINE

Tools | Materials

•Screwdrivers—standard, Phillips and Torx.

•Power drill.

•Standard socket and wrench set.

•2' level.

•Tubing cutter.

•3' (.9 m) of 1/4" OD copper, braided stainless steel or

PEX tubing.

•Saddle valve.

•Material to protect home, ooring and cabinetry during

installation.

Rating plate location.

RATING

PLATE

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Opening Dimensions

ICE MACHINE

IMPORTANT NOTE: It is recommended that the electrical

and water supply be placed in an adjacent cabinet. If they

are placed within the opening, additional cabinet depth may

be required.

151/4"

(387)

OPENING

WIDTH

341/2"

(876)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

TOP VIEW

SIDE

VIEW FRONT VIEW

subzero.com

SITE PREPARATION

Electrical

Installation must comply with all applicable electrical codes.

Although it can be located anywhere on the back wall, it

is recommended that the electrical supply be placed in an

adjacent cabinet or in the lower right of the opening. Refer

to the illustration below. A separate circuit, servicing only

this appliance is required.

Model UC-15I(P)O is designed and safe for use in outdoor

applications. When installed outdoors, a ground fault circuit

interrupter (GFCI) is required to reduce the risk of electrical

shock. A GFCI is not recommended for use with the indoor

model and may cause interruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

Electrical supply location.

CAUTION

The outlet must be checked by a qualied electrician to

be sure that it is wired with the correct polarity. Verify

that the outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter or

remove the power cord ground prong.

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Preparation

CAUTION

Before moving the unit into position, secure the door

closed and protect any nished ooring.

Uncrate the unit and inspect for damage. Remove the wood

base and discard shipping bolts and brackets. Remove and

recycle packing materials. Do not discard the kickplate and

hardware.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

Plumbing

Installation must comply with all applicable plumbing codes.

The water supply line should be located as shown in the

illustration below. The water supply line should be con-

nected to the house supply with an easily accessible shut-

off valve. Do not use self-piercing valves.

A reverse osmosis system can be used provided there is

constant water pressure of 20–80 psi (1.4–5.5 bar) supplied to

the unit at all times. A copper line is not recommended for

this application.

PLUMBING REQUIREMENTS

Water Supply Line 1/4" OD copper, braided stain-

less steel or PEX tubing

Water Pressure 20–80 psi (1.4–5.5 bar)

Excess Water Line for Connection 36" (914)

ICE MACHINE DRAIN

The ice machine can be ordered with or without a drain

pump. Models without a pump will drain water by gravity.

A drain must be installed.

The drain and inlet water tubes must be plumbed before

connecting to the ice machine. For the gravity drain, hori-

zontal drain lines must have a 1/4"(6) per 12" (305) fall. An

air gap will likely be required between the unit and drain.

A stand pipe with a trap below is acceptable for the drain.

341/2" (876)

ROUGH

OPENING

HEIGHT

335/8" (854)

MINIMUM

HEIGHT

REQUIRED

151/4"min (387)

ROUGH

OPENING WIDTH

24" (610)

ROUGH

OPENING

DEPTH

POSITION OUTLET

WITH GROUNDING

PRONG ON RIGHT

LOCATION OF

WATER LINE

(203)

1/2"

(13)

TOP VIEW

FRONT VIEW

4" (102)

LOCATE

ELECTRICAL

WITHIN

SHADED AREA

Water supply location.

subzero.com

Installation

INSTALL ICE MACHINE

1Adjust the leveling legs close to the desired height. Refer

to the illustration below.

2Reverse the door swing if needed. Refer to steps out-

lined on page 9.

3Gravity drain model: Install the drain hose provided,

onto the drain tting on the back of unit and route to

the open site drain. Refer to the illustration below and

plumbing requirements on the previous page.

Drain pump model: Route drain tubing through the drain

tting on the back of the unit and install the drain hose

provided, on the drain pump. Route the other end of

the drain tubing to the drain site. Refer to the illustration

below and plumbing requirements on the previous page.

4Use a compression tting to connect the water inlet on

back of ice machine to the prepared 1/4" (6) OD cold

water line. Refer to the illustration below.

5Open the shut-off valve on the water line. Check all

plumbing connections for leaks. Failure to do so could

result in ooding.

6Plug the power cord into the grounded receptacle.

7Level the ice machine to assure the door closes and

seals properly. Place a level on top of the unit and turn

each leveling leg to raise or lower as needed.

8Move the ice machine into its nal position.

9Anchor the ice machine by installing two at head

screws provided through each hinge. Refer to the illus-

tration below.

INSTALLATION

ANCHORING

SCREWS

Anchoring.

LEVELING

LEG

WATER INLET

DRAIN FITTING

Leveling.

Drain connection.

Sub-Zero Customer Care 800.222.7820

INSTALLATION

Installation

VERIFY ICE PRODUCTION

1Press ‘POWER’ to turn the ice machine on.

2Add one gallon (3.8 L) of cold water to the ice bin. Verify

the water completely drains from the ice bin and there

are no leaks. If the water has not drained within 60 sec-

onds, there may be a kink in the drain tube or incorrect

drain installation.

3Press ‘CLEAN’. Wait three minutes until the CLEAN light

ashes, then add 1 tablespoon (15 ml) of undiluted ice

machine sanitizer directly into the spray area. Refer to

the illustration below. Use only the sanitizer made for the

Sub-Zero ice machine available at subzerowolfstore.com.

For questions, contact Sub-Zero customer care at

800-222-7820.

Water shutters location.

WATER

SHUTTERS

4A 10-minute sanitizing cycle begins, followed by eight

rinse cycles. When the process is complete, the CLEAN

light will no longer be illuminated. The entire cycle takes

approximately 30 minutes.

5At initial start-up, the ice machine will need approxi-

mately 30 minutes to freeze ice cubes and up to ve

minutes to harvest. Verify completion of the rst cycle ice

production to conrm proper installation.

subzero.com

Installation

REVERSE DOOR SWING

The door hinges are designed to be placed on either the

right or left side of the ice machine. The unit is shipped with

the door hinged on the right. Moving the hinges to the left in

pre-drilled holes, allows for a left-hand door swing.

To reverse door swing:

1Detach the hinges from the ice machine by removing two

screws per hinge, then remove the door. Remove the

shim located between the cabinet and bottom hinge, this

shim will transfer to the left side bottom hinge.

2Detach the hinges from the door by removing two

screws per hinge.

3Detach the right-hand upper trim (shaded area) from the

door by removing two screws. Refer to the illustration

below. Replace it with the left-hand upper trim.

4Transfer the hinges to the left side of the door and

reinstall. The upper hinge will now be in the lower hinge

position and the lower hinge in the upper hinge position.

5Remove the top cover of the ice machine by removing

two screws at the top rear of the unit.

6Remove four screws from the front top rail, then pivot

the top rail end for end to expose the two left-hand top

hinge mounting holes and reinstall. Refer to the illustra-

tion below.

7Remove two screws from the lower edge of the bottom

trim plate and slide it to the right to cover the right hinge

mounting holes. Refer to the illustration below. The left

hinge mounting holes will now be exposed.

8Reinstall the shim removed in step 1, between the

cabinet and the left side bottom hinge. Reinstall the door

by mounting the hinges using the left hinge mounting

holes. Verify operation of door.

INSTALLATION

HINGE

SCREWS

UPPER

TRIM (RH)

HINGE

Remove door.

Detach hinges and trim.

TOP RAIL

SCREWS

TRIM PLATE

SCREWS

Front top rail.

Bottom trim plate.

Sub-Zero Customer Care 800.222.7820

INSTALLATION

Custom Panel

OVERLAY PANEL

For overlay applications, a custom door panel must be

installed. Panel size is critical for a proper t. To verify panel

requirements and dimensions, refer to the Sub-Zero design

guide at subzero.com/specs.

Finish all sides of the custom panel. They will be visible

when the door is open.

A D-style handle is recommended. The door handle must be

located near the edge of the panel opposite the hinge, cen-

tered top to bottom. Stainless steel tubular and pro handles

are available through an authorized Sub-Zero dealer. For

local dealer information, visit the nd a showroom section

of our website, subzero.com.

PANEL INSTALLATION

Remove the handle side bracket attached to the front of the

door. Place the custom overlay door panel face down on a

protected work surface. On the back of the panel, position

the plastic template provided, ush with the top and side

edges. Verify proper location for right-hand (RH) or left-hand

(LH) door swing. Refer to the illustration below.

Mark the holes, remove the template and drill pilot holes for

the brackets. Position and secure the mounting bracket with

screws provided.

To install the custom door panel, partially insert a screw in

the center of each mounting position on the hinge side of

the door. Engage the tabbed bracket to the handle side

of the door, then slide the hinge side mounting bracket onto

positioning screws. Slotted holes on the mounting bracket

should slide under screw heads to support the panel. Refer

to the illustration below. Panel can be adjusted 1/4"(6) up

and down and side to side.

Once the custom panel is in place and properly adjusted,

attach remaining screws to the hinge side mounting bracket

and install hinge covers.

DOOR

PANEL

BRACKET

CAP

SCREW

Template position.

Panel installation.

Andere Handbücher für UC-15I

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sub-Zero Eiswürfelbereiter Handbücher

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero 506 Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero 235 Bedienungsanleitung

Sub-Zero

Sub-Zero 506 Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Bedienungsanleitung

Sub-Zero

Sub-Zero Undercounter Ice Machine Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Leitfaden

Sub-Zero

Sub-Zero UC-15IPO Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Leitfaden

Sub-Zero

Sub-Zero 315I Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Gebrauchsanweisung

Sub-Zero

Sub-Zero UC-15I Leitfaden

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero 315 Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Bedienungsanleitung

Sub-Zero

Sub-Zero 315I Leitfaden

Sub-Zero

Sub-Zero UC-15IO Bedienungsanleitung

Sub-Zero

Sub-Zero UC-15I Leitfaden

Sub-Zero

Sub-Zero 235 Bedienungsanleitung

Sub-Zero

Sub-Zero Wolf ICB700 Series Bedienungsanleitung

Beliebte Eiswürfelbereiter Handbücher anderer Marken

Hoshizaki

Hoshizaki KMD-460MWJ Bedienungsanleitung

Unold

Unold 48945 Bedienungsanleitung

Kenmore

Kenmore 2217402A Bedienungsanleitung

Cornelius

Cornelius WM600 Betriebsanleitung

GE XPIO43SCSS Bedienungsanleitung

Hoshizaki

Hoshizaki KMD-901MAH Bedienungsanleitung

Whynter

Whynter FIM-450HA Bedienungsanleitung

U-Line

U-Line UMCR014-SC01A Installationshandbuch

Andrew James

Andrew James AJ000522 Bedienungsanleitung

Scotsman

Scotsman CME1356 Bedienungsanleitung

Scotsman

Scotsman ACM 25 Bedienungsanleitung

Kärcher

Kärcher IP 120 Bedienungsanleitung

U-Line

U-Line SS1095 Bedienungsanleitung

Maytag

Maytag MIM1554WRS - Ice Maker Bedienungsanleitung

Hoshizaki

Hoshizaki KM-630MAH Bedienungsanleitung

Princess

Princess Yonanas Bedienungsanleitung

Unold

Unold 48946 Bedienungsanleitung

Electrolux

Electrolux E15IM60GP Bedienungsanleitung