Sub-Zero 700BCI Bedienungsanleitung

I STALLATIO GUIDE

Integrated Refrigeration

Important Note

To ensure the safe and efficient installation of Sub-Zero

equipment, please take note of the following types of

highlighted information throughout this guide:

IMPORTA T OTE highlights information that is especially

relevant to a problem-free installation.

CAUTIO signals a situation where minor injury or product

damage may occur if instructions are not followed.

WAR I G states a hazard that may cause serious injury or

death if precautions are not followed.

Contents

Integrated Refrigeration .......................... 3

Model Specifications ............................ 4

Site Preparation ................................. 7

Integrated Installation ........................... 12

Service Information ............................. 22

Features and specifications are subject to change at any time

without notice. Visit subzero.com/specs for the most up-to-

date information.

IMPORTA T OTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specified.

Sub-Zero Integrated Refrigeration

The importance of the installation of the Sub-Zero

integrated unit cannot be overemphasized. Installation

should be done by a qualified installer.

Before you begin the installation process, it is recom-

mended that you read this entire installation guide. There

are key details that you should take special care to

observe during the installation. By reading these instruc-

tions carefully, you will make the installation process

easier, problem-free and most importantly, safe.

Any questions or problems regarding the installation

should be directed to your authorized Sub-Zero dealer or

Sub-Zero customer care at 800-222-7820. You may also

check the contact & support sectionofour website,

subzero.com.

Important product information, including the model and

serial number of your unit are listed on the product rating

plate. For column models, the rating plate is located inside

the top drawer near the drawer guide opposite the hinge.

For tall and drawer models, the rating plate is located

inside the cabinet, to the left of the upper drawer. Refer to

the illustrations below.

Integrated Refrigeration 3

subzero.com/specs

Before You Start

Make sure the opening dimensions, door and drawer

clearances, electrical service and plumbing are correct for

the model you are about to install. Refer to specifications

on the following pages.

IMPORTA T OTE: The inside edges of the rough

opening, as well as the sides and a portion of the

backside of the decorative panels will need to be finished,

as they will be exposed when the doors are open.

TOOLS A D MATERIALS REQUIRED

•Appliance dolly able to support 500 lbs (227 kg) and

adequate manpower to handle the weight of the unit.

•Phillips and slotted screwdrivers.

•Allen, standard and crescent wrenches.

•Various sized pliers.

•5/16" hex bolt nut driver.

•Cordless drill and assorted drill bits.

•Level—2' (.6 m) and 4' (1.2 m) recommended.

•4' (1.2 m) of 1/4" copper, braided stainless steel or

PEX tubing and saddle valve for water line (do not use

self-piercing valves).

•Tubing cutter.

•Masonite, plywood, pressed fiberboard, cardboard or

other suitable material to protect finished flooring.

•Appropriate materials to cover and protect the home

and furnishings during installation.

Tall and drawer models.Column models.

RATING PLATE

Model Specifications 4

MODELS IC-27R A D IC-27FI

27" (686)

14"(356)

15/8"

(41)

24"

(610)

81"

(2057)

TO TOP OF

OPENNG

24" (610)

789/16"

(1995)

93/4"(248)

(102)

1/2"(13) ± ADJUSTMENT IN LEVELING LEGS

251/2"

(648)

45/8"

(117)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

Overall Dimensions

COLUM MODELS

MODELS 700TR, 700TFI A D 700TCI

27" (686)

14"(356)

13/16"

(21)

341/2"

(876)

24"

(610)

203/8"

(518)

101/4"

(260)

131/4"

(337)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

251/2"

(648)

45/8"

(117)

80"

(2032)

TO TOP OF

OPENNG

24" (610)

789/16"

(1995)

93/4"

(248)

(102)

HEIGHT DIMENSIONS ± 1/2"(13)

27" (686) TALL MODELS

Model Specifications 5

subzero.com/specs

MODELS 736TR, 736TFI A D 736TCI

36" (914)

14"(356)

80"

(2032)

TO TOP OF

OPENNG

24" (610)

15/16"

(33)

7713/16"

(1976)

341/2"

(876)

24"

(610)

203/8"

(518)

101/4"

(260)

131/4"

(337)

93/4"

(248)

(102)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

341/2"

(876)

7" (178)

HEIGHT DIMENSIONS ± 1/2"(13)

Overall Dimensions

36" (914) TALL MODELS

Model Specifications 6

Interior Capacity R cu ft (L) F cu ft (L)

COLUM MODELS

IC-27R 16.2 (459)

IC-27FI 16.3 (462)

27" (686) TALL MODELS

700TR 15.5 (439)

700TFI 15.3 (433)

700TCI 10.2 (289) 5.1 (144)

36" (914) TALL MODELS

736TR 20.9 (592)

736TFI 21.5 (609)

736TCI 13.3 (377) 7.1 (201)

27"(686) DRAWER MODELS

700BR 5.3 (150)

700BF(I) 5.1 (144)

700BC(I) 2.9 (82) 2.1 (59)

Shipping Weight lbs (kg)

IC-27R, IC-27FI, 700TR, 700TFI and 700TCI 360 (163)

736TR, 736TFI and 736TCI 480 (218)

700BR, 700BF(I) and 700BC(I) 190 (86)

MODELS 700BR, 700BF(I) A D 700BC(I)

27" (686)

341/2"

(876)

24"

(610)

203/8"

(518)

DIMENSIONS WILL VARY WITH PANEL THICKNESS

1/2"

(13)

3/8"

(10)

191/2"

(495)

257/8"(657)

24" (610)

93/4"(248)

(102)

101/4"

(260)

131/4"

(337)

HEIGHT DIMENSIONS ± 1/2"(13)

Overall Dimensions

DRAWER MODELS

Specifications

I TEGRATED MODELS

Site Preparation 7

subzero.com/specs

IMPORTA T OTE: The depth of each integrated model is

24" (610) from the front of the unit to its back. Your design

may necessitate moving the unit back or cabinets forward to

achieve a flush fit. This will require a minimum rough opening

depth of 25" (635).

25" (635)

OPENING

DEPTH

OPENING WIDTH

25" (635)

OPENING DEPTH

OPENING

HEIGHT

TOP VIEW

FRONT VIEWSIDE VIEW

Opening Dimensions

I TEGRATED MODELS

Opening Dimensions AB

IC-27R and IC-27FI 27" (686) 81" (2057)

700TR, 700TFI, 700TCI 27" (686) 80" (2032)

736TR, 736TFI, 736TCI 36" (914) 80" (2032)

700BR, 700BF(I), 700BC(I) 27" (686) 341/2"(876)

Site Preparation 8

Electrical Requirements

The electrical supply should be located within the shaded

area shown in the illustrations below. Follow the National

Electrical Code and local codes and ordinances when

installing the receptacle. A separate circuit, servicing only

this appliance is required. A ground fault circuit interrupter

(GFCI) is not recommended and may cause interruption of

operation.

IMPORTA T OTE: It is critical that the electrical outlet be

located within the shaded area shown so it does not inter-

fere with installation of the anti-tip bracket. It must be

flush with the back wall and positioned with the grounding

prong to the right of the thinner blades.

Electrical Requirements

Power Supply 115 V AC, 60 Hz

Circuit Breaker 15 amp

Receptacle 3-prong grounding-type

Do not use an extension cord or two-prong adapter.

Do not remove the power supply cord ground prong.

The outlet must be checked by a qualified electrician

to be sure that it is wired with the correct polarity. Verify

that the outlet is properly grounded.

13" (330)

1/4"

(6)

41/2"

(114)

LEFT SIDE

OF OPENING

FLOOR

21/2"

(64)

FRONT VIEW

27" (686) models. 36" (914) models.

171/2"(445)

41/2"

(114)

FRONT VIEW

FLOOR

1/4"

(6)

LEFT SIDE

OF OPENING

21/2"

(64)

Site Preparation 9

subzero.com/specs

Plumbing Requirements

For integrated models with an automatic ice maker, the

water supply line should be located through the floor or

back wall, within the shaded area shown in the illustra-

tions. Routing the line in these locations will avoid any

interference with the anti-tip bracket.

IMPORTA T OTE: Do not route the water supply line in

front of the compressor tray. The tray must be slid forward

for service.

The water supply line should be connected to the house

supply with an easily accessible shut-off valve between

the supply and the unit. Do not use self-piercing valves.

A saddle valve kit is available from your authorized

Sub-Zero dealer.

An in-line filter is required when water conditions have

a high sediment content.

A reverse osmosis system can be used provided there is

constant water pressure of 20 psi (1.4 bar) to 100 psi

(6.9 bar) supplied to the unit at all times. In some cases,

a reverse osmosis water filter system may not be able to

maintain the minimum pressure consistently. A copper line

is not recommended for this application.

IMPORTA T OTE: All installations must meet local

plumbing code requirements.

3" (76)

(229)

3/4"

(19)

FLOOR

21/2"(64)

FRONT VIEW

27" (686) models.

(229)

(152)

TOP VIEW

11/2"

(38)

21/2"(64)

BACK

WALL

11/2"(38)

131/2"

(343)

3" (76)

FRONT VIEW

3/4"

(19)

FLOOR

21/2"(64)

36" (914) models.

131/2"

(343)

TOP VIEW

(152) 11/2"

(38)

BACK

WALL

21/2"(64)

11/2"(38)

Plumbing Requirements

Water Supply Line 1/4" OD copper, braided stainless steel

or PEX tubing

Water Pressure 20–100 psi (1.4–6.9 bar)

Excess Water Line for Connection 27" (686)

Site Preparation 10

An anti-tip bracket and hardware is provided with the inte-

grated unit. Placement of the anti-tip bracket is critical to

a stable installation. The anti-tip bracket must be installed

on a solid base.

If you are installing the unit in a space deeper than 24"

(610), be sure to locate the anti-tip bracket so that it

engages the unit properly. It is important that the anti-tip

bracket is placed 24" (610) from the front of the unit

(without panels) to the back of the anti-tip bracket.

IMPORTA T OTE: In some installations the subflooring

or finished floor may require angling the wood screws

used to fasten the anti-tip bracket to the back wall.

WOOD FLOOR APPLICATIO S

Use the six #12 x 21/2" wood screws and the six 1/4" flat

washers provided. Drill pilot holes 3/16"(5) diameter

maximum, and make sure the screws penetrate through

the flooring material and into the wall plate a minimum of

3/4"(19). Make sure the screws hold tight. Refer to the

illustration below.

CO CRETE FLOOR APPLICATIO S

Use the two 3/8" x 33/4" concrete wedge anchors, two

#12 x 21/2" wood screws and two 1/4" flat washers

provided. Make sure the anchors and screws hold tight.

Refer to the illustration below.

Anti-Tip Bracket Installation

Make sure there are no electrical wires or plumbing

in the area which the screws could penetrate.

To prevent the unit from tipping forward and provide

a stable installation, the unit must be secured in place

with the anti-tip bracket provided with the unit.

Anti-Tip Bracket Placement A

27" (686) Models 131/2"(343)

36" (914) Models 18" (457)

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

11/2"(38)

min

Wood floor. Concrete floor.

Andere Handbücher für 700BCI

Dieses Handbuch passt für folgende Modelle

Andere Sub-Zero Kühlschrank Handbücher

Sub-Zero

Sub-Zero UC-24C Montageanleitung

Sub-Zero

Sub-Zero 700TF Betriebsanleitung

Sub-Zero

Sub-Zero IC-27R Bedienungsanleitung

Sub-Zero

Sub-Zero 400 Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-30UG Bedienungsanleitung

Sub-Zero

Sub-Zero IC-24FI Bedienungsanleitung

Sub-Zero

Sub-Zero Wolf 400 Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-30UG Bedienungsanleitung

Sub-Zero

Sub-Zero 700BR Bedienungsanleitung

Sub-Zero

Sub-Zero PRO3650GRH Bedienungsanleitung

Sub-Zero

Sub-Zero 736TC Bedienungsanleitung

Sub-Zero

Sub-Zero Built-in Series Betriebsanleitung

Sub-Zero

Sub-Zero 736TR Montageanleitung

Sub-Zero

Sub-Zero BI-48SD Montageanleitung

Sub-Zero

Sub-Zero Designer Series Bedienungsanleitung

Sub-Zero

Sub-Zero Classic Series Bedienungsanleitung

Sub-Zero

Sub-Zero BI-42SD Bedienungsanleitung

Sub-Zero

Sub-Zero Designer Series Bedienungsanleitung

Sub-Zero

Sub-Zero Classic Series Bedienungsanleitung

Sub-Zero

Sub-Zero 648PRO Bedienungsanleitung

Sub-Zero

Sub-Zero 424FS Leitfaden

Sub-Zero

Sub-Zero ICBB-36R Leitfaden

Sub-Zero

Sub-Zero 600 Series BI-48S Bedienungsanleitung

Sub-Zero

Sub-Zero 601R-2 Betriebsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung