SUGATSUNE Aileron Lift-Assist Bedienungsanleitung

Sugatsune Aileron Lift-Assist

Soft-Close Hinge Set

1) This system mounts onto a 35 mm hinge set

from Sugatsune. Determine the spacing of the

hinges and mark their locations by drawing a

centerline for each hinge component.

4) Reset the depth of the combo square to 19

millimeters.

2) Set the depth of the combo square to 20.5 mil-

limeters. Here the measurement is transfered to

a combo square.

5) Draw a wide cross mark on the hinge center-

lines on the cabinet body. These will locate the

hinge plates.

3) Place a cross mark on each hinge centerline

on the lid. This will locate the cup hinges on the

inside of the cabinet lid.

6) Reset the combo square to 118 mm. Choose

which side to mount the lid stay. Extend that

hinge centerline and mark a cross line where the

lid stay will attach to the lid.

The Aileron Lift-Assist system installs over a pair of 35 mm hinges.

There are two different versions available: one with high tension

lift, and the other with medium tension. The system comes

prepackaged with all the hardware required. See image below.

7) Chuck a 35 mm Forstner bit into the drill

press. Set the depth to 11 mm into the 3/4" lid.

Bore the holes at the marked locations.

10) Place the hinge plates in their locations and

mount them using the screws provided.

13) Remove the forward two screws on the lid

stay hinge plate. Loosen the rear two screws.

Slide the lid stay onto the lid stay plate.

16) Adjust the

closing force.

8) Use a scratch awl to make divots at the screw

locations. They will help locate the drill bit on the

cabinet body. Do this in both locations.

11) Place the hinge cups in their locations and

drill holes for their screws. Drive the screws

home.

14) Mount the lid stay to the lid stay plate by

tightening the rear screws and reinstalling the

forward two screws.

9) With a Vix bit in a drill driver, drill the screw

holes for the hinge plate, using the divots to

accurately locate the holes.

12) Bore the holes for the Aileron lid stay plate.

Mount the lid stay plate.

15) Adust the lift force.

ADJUSTMENTS

Andere SUGATSUNE Türöffnungssystem Handbücher

SUGATSUNE

SUGATSUNE Lapcon SDS-C301N-BLK Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP FD50-H Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP LM-80 Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP FD35EV Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP LL-66S Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP FD50-H Bedienungsanleitung

SUGATSUNE

SUGATSUNE Lamp FD30-F Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP ALT-F Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP MonoFlat FAD Series Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP DC Series Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP FD80-H Bedienungsanleitung

SUGATSUNE

SUGATSUNE Zwei L ZL-2402 Bedienungsanleitung

SUGATSUNE

SUGATSUNE EB-90 Bedienungsanleitung

SUGATSUNE

SUGATSUNE SDS-C301N Bedienungsanleitung

SUGATSUNE

SUGATSUNE HES2S-140-A125 Bedienungsanleitung

SUGATSUNE

SUGATSUNE LAMP Lapcon SDS-210 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung