Summit FF27BSS Bedienungsanleitung

Write Serial Number here:

Model No.:

Serial No.:

Instruction Manual

Models:

FF27BSS

LC27BSS

SPR2700SS

Single-Zone Refrigerator

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES

AND OPERATING INSTRUCTIONS. KEEP THIS MANUAL IN A SECURE LOCATION.

IMPORTANT SAFETY INSTRUCTIONS

•Read all instructions before using the appliance.

•This appliance can be used by children aged 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or

instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children

shall not play with the appliance. Cleaning and user maintenance shall not be done by children without

supervision.

•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly

qualified personnel in order to avoid an injury or malfunction.

•WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.

•WARNING: Do not use multiple portable socket outlets or portable power supplies at the rear of the

appliance.

•WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of

obstructions.

•WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than

those recommended by the manufacturer.

•WARNING: Do not damage the refrigerant circuit.

•WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless

they are of the type recommended by the manufacturer.

•Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

•This appliance is intended to be used in household and similar applications such as

– staff kitchen areas in shops, offices, and other working environments.

– farmhouses and by clients in hotels, motels, and other residential-type environments.

– bed and breakfast type environments.

– catering and similar non-retail applications.

•Plug the unit into a grounded 3-prong outlet. Do not remove the grounding prong, do not use an adapter,

and do not use an extension cord.

•It is recommended that a separate circuit, serving only your appliance, be provided. Use receptacles that

cannot be turned off by a switch or pull chain.

•Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion.

•Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is

disconnected.

•Do not connect or disconnect the electric plug when your hands are wet.

•Unplug the appliance or disconnect the power before cleaning or servicing. Failure to do so can result in

electrical shock or death.

•Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this

manual. All other servicing should be referred to a qualified technician.

•Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other

appliance. The fumes can create a fire hazard or explosion.

•Use two or more people to move/install the refrigerator. Failure to do so can result in back or other injuries.

•To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.

Choose a well-ventilated area with temperatures above 50°F (10°C) and below 100°F (38°C). This unit must

be installed in an area protected from the elements, such as wind, rain, water spray, or drips.

•The appliance should not be located next to ovens, grills, or other sources of high heat.

•The appliance must be installed with all electrical connections in accordance with state and local codes. A

standard electrical supply (115V AC 60 Hz), properly grounded in accordance with the National Electrical

Code and local codes and ordinances, is required.

•Do not kink or pinch the power supply cord of the appliance.

•The fuse (or circuit breaker) size should be 15 amps or higher.

•It is important for the appliance to be leveled in order to work properly. You may need to make several

adjustments to level it.

Although the unit has been tested at the factory, due to transit and storage, you should clean the appliance

before use.

•Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or

discolor the interior.

•Do not use this apparatus for other than residential purposes.

•This appliance is CFC and HFC-free and contains small quantities of Isobutane (R600a) which is

environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the

greenhouse effect. Care must be taken during transportation and setting up of the appliance that no parts of

the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.

•In the event of any damage:

- Avoid open flames and anything that creates a spark,

- Disconnect from the electrical power line,

- Air the room in which the appliance is located for several minutes and contact the Service Department for

advice.

•The more coolant there is in an appliance, the larger the room it should be installed in. In the event of a

leakage, if the appliance is in a small room, there is the danger of combustible gases building up. For every

ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant in the appliance

is stated on the data plate on the back of the appliance. It is hazardous for anyone other than an authorized

Service Personnel to carry out servicing or repairs to this appliance.

•Take serious care when handling, moving and using the appliance to avoid either damaging the refrigerant

tubing or increasing the risk of a leak.

•Replacing component parts and servicing shall be done by factory-authorized service personnel so as to

minimize the risk of possible ignition due to incorrect parts or improper service.

•When you dispose of the appliance, take off the door and leave the shelves in place so that children may

not easily climb inside. And make sure the coolant circuit, particularly the heat exchanger at the back/bottom

of the unit is not damaged.

•The recycle symbol on the product or its packaging indicates that this product is not to be

handled as normal household waste and it is to be taken to a recycling collection point for

electrical and electronic goods.

The appliance must be positioned so that the plug is easily accessible after installation.

- SAVE THESE INSTRUCTIONS -

Before Using Your Appliance

INSTALLATION INSTRUCTIONS

•Remove the exterior and interior packing.

•Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This will

reduce the possibility of a malfunction in the cooling system from handling during transportation.

•Clean the interior surface with lukewarm water using a soft cloth.

•Install the handle on the door using the screws that are provided. (See: Installation of the Handle)

Installation of Your Appliance

•This appliance is designed for free-standing or built-in (fully recessed) installation.

•Place your appliance on a floor that is strong enough to support it when it is fully loaded. To level your

appliance, adjust the front leveling legs at the bottom.

•Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct

sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extremely

cold ambient temperatures may also cause the unit not to perform properly.

•For free-standing installation, 5” (127mm) of space between the back and sides of the appliance, and 4”

(102mm) at the top, are suggested. This allows the proper air circulation to cool the compressor and

condenser. For built-in installation, keep ¼” (6.35mm) of space between the top and sides of the appliance,

and 2” (51mm) at the rear. Make sure the air vent at the front of the appliance is never covered or blocked in

any way.

•If this appliance is intended to be installed in a space between two units, the minimum space required is:

26.97in wide × 23.6in deep × 34.06in high

•Avoid locating the unit in moist areas.

•Plug the appliance into an exclusive, properly installed, and grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power

and/or grounding should be directed toward a certified and authorized products service center.

Installation of the Handle

To install the handle, please follow these instructions:

•Place the handle (Fig.1) over the pins (Fig.2) of the door

•Tighten the handle by screwing in screws with an Allen

wrench (not included) (Fig.3).

How to put off the shelves

1. Take out all items from the shelves.

2. Please keep the door open fully all the way before pulling the shelves out.

3. Push the shelf backward (Fig.1) until the groove on either side of the shelf is level with the plastic peg on

either side of the cabinet. (Fig.2). Uptilt the shelf from one side (Fig.3), and then firmly pull out the shelf.

(Fig.4).

Reversing the Door Swing

This appliance has the ability to have

the door open from the left or right side.

The unit is delivered to you with the

door opening from the left side. Should

you desire to reverse the opening

direction, please follow the instructions

below. To make the reversal, you will

find two hardware pieces in a plastic

bag inside the appliance: the top left

hinge and the bottom left hinge. The

bottom support bracket is used for

both sides.

1. Carefully lay the appliance on its back. Use cushioning to protect the floor and the appliance.

2. Using a Philips screwdriver, remove the two screws and bottom right hinge beneath the door. Keep the

hinge in a safe place in case you need to reverse the door again in the future. (Fig.1)

3. Carefully slide the door off and place it on a padded surface.

4. Interchange the plastic shaft sleeves at the top of the door. (Fig.2)

5. Remove the bottom support bracket from the right side. (Fig.3)

6. Remove the top right hinge and keep it in a safe place in case you want to reverse the door in the

future. (Fig.4)

7. Remove the screws from the top left and transfer them to the right.

8. Install the top left hinge. (Fig.5)

9. Install the bottom left hinge to the door. Do not over-tighten the screw.

10. Place the door back on the appliance, lining up the top hinge.

11. Install the bottom support bracket. (Fig.6)

12. Adjust door alignment. When set, tighten the screw on the hinge.

13. Remove the handle. Transfer the screw hole covers to the left and install the handle on the right.

NOTE: Some variations of this unit's door may not be reversible in the field. For more information, visit

our website.

OPERATION

The appliance should be placed where the ambient temperature is between 50~100°F (10~38°C). If the

ambient temperature is above or below this range, the performance of the unit may be affected. Placing

your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate.

Connect the power cord to a properly grounded outlet.

This appliance is equipped with Memory IC – should there be a power interruption, the unit will auto-recover

at the last setting.

Control Panel:

Setting the Temperature Control

Adjustable temperature: 36°F to 46°F (2°C to 8°C)

Set the desired temperature by pressing the corresponding buttons, to increase or to decrease.

Each press is a 1-degree increment. Once released, the set temperature will flash for approximately 5

seconds then revert to display the internal temperature.

To view your set temperature, press either the or button once and the LED display will flash the set

temperature for 5 seconds.

The appliance has the capability to display temperature in either Celsius or Fahrenheit. To change the

temperature scale, press and hold both buttons simultaneously for approx. 3 seconds.

Note: The temperature inside may vary slightly depending on whether or not the interior bulb is ON or OFF and

where the bottles are located (upper/middle or lower section).

ECO mode:

Press and hold the button

for 3 seconds, it can enter or exit ECO mode.

In this mode, the interior LED light, the compressor indicator and the temperature value on the display

panel will be turned off and the ° will illuminate in the upper left corner of °C / °F.

Light / Lock

LED lamp brightness mode: with Memory IC (when the unit restarts after power failure unit will auto recover

at the last setting), the default brightness is 100%.

Each time the button is pressed, the brightness of the LED will be cycled from the four positions

(100%, 75%, 50%, OFF)

Press and hold for 3 seconds to lock or unlock the control panel.

ON/OFF Power / Mute

To turn the appliance on or off, press and hold the ON/OFF button for 3 seconds.

When the high-temperature alarm or low-temperature alarm is activated, the buzzer will sound continuously.

Press one time alarm will be closed.

LOCK

If illuminated, indicates the control panel is locked.

RUN

When unit’s compressor is running, this indicator light will illuminate to signify that cooling mode is currently in

operation.

Demo mode

Press and hold buttons , and simultaneously for 10 seconds, it can enter or exit demo

mode.

In this mode, the display panel can operate settings, but the temperature is fixed display 12°C (54°F), all

fans, the compressor does not start.

Defrosting

The unit defrosts automatically in normal operating conditions.

The evaporator behind the rear wall of the unit defrosts automatically. Water will drain through the drain pipe

from the back of the product. Users need to bring the water to the drain or find an appliance to load the

water. (If loading with an appliance, you need to pay attention to clearing the water regularly).

However, frost may accumulate on the evaporator if the unit is repeatedly opened in high heat or high

humidity location. If this frost pattern does not clear within 24 hours, your unit will require manual defrosting.

Mandatory defrost mode: Press the and at simultaneously for 10 seconds, and the appliance will

enter mandatory defrost mode.

Sabbath mode

Press and hold buttons and at the same time for at least 5 seconds to enter or exit Sabbath mode.

In this mode, LED will display "Sb". This mode turns off the displays, and interior lights and prevents them

from turning on again. Normal cooling operations will still take place. The compressor and the fan work

normally.

When the cabinet powers off, it will not automatically exit Sabbath mode, and it will keep Sabbath mode

when power is on again. The Sabbath Mode will automatically turn off after 96 hours.

CARE AND MAINTENANCE

Cleaning Your Appliance

1. Turn off the power, unplug the appliance, and remove all items including shelves and racks.

2. Wash the inside surfaces with a warm water and baking soda solution. The solution should consist of about

2 tablespoons of baking soda to a quart of water.

3. Wash the shelves with a mild detergent solution.

4. Wring excess water out of the sponge or cloth when cleaning the area of the controls or any electrical parts.

5. Wash the exterior of the cooler with a warm solution of mild liquid detergent. Rinse well and wipe dry with a

clean, soft cloth.

Power Failure

Most power failures are corrected within a few hours and should not affect the temperature of your appliance if

you minimize the number of times the door is opened. If your power is going to be off for a longer period of time,

you need to take the proper steps to protect your contents.

Vacation Time

Short vacations: Leave the appliance operating during vacations of less than three weeks.

Long vacations: If the appliance will not be used for several months, remove all items, and turn off the

appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly,

propping it open if necessary.

Transporting Your Appliance

If you need to move your appliance once the box has been discarded:

1. Securely tape down all loose items (shelves) inside your appliance.

2. Turn the adjustable legs up to the base to avoid damage.

3. Tape the door shut.

4. Be sure the appliance stays secure in an upright position during transportation. Also, protect the outside of

the appliance with a blanket or similar item.

Energy Saving Tip

The appliance should be located in the coolest area of the room, away from heat-producing appliances

and out of direct sunlight.

Ensure that the unit is adequately ventilated. Never cover air vents.

Do not keep the door open any longer than necessary.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Summit Kühlschrank Handbücher

Summit

Summit FFBF287SSIM Bedienungsanleitung

Summit

Summit FFRF24SS Bedienungsanleitung

Summit

Summit SUM-P01060 Bedienungsanleitung

Summit

Summit FF510L Leitfaden

Summit

Summit SCR-1300 Leitfaden

Summit

Summit SP6DS2DOS SERIES Leitfaden

Summit

Summit FF1088W Bedienungsanleitung

Summit

Summit FFBF192SSBI Bedienungsanleitung

Summit

Summit ASDS1523 Bedienungsanleitung

Summit

Summit GLOBAL INDUSTRIAL GIDIFFBF283SS Bedienungsanleitung

Summit

Summit SP7D2 Bedienungsanleitung

Summit

Summit FF412ES Bedienungsanleitung

Summit

Summit SP6DS-2D Bedienungsanleitung

Summit

Summit FF7LBL Leitfaden

Summit

Summit FF410WH Bedienungsanleitung

Summit

Summit FF6SSTB Leitfaden

Summit

Summit FF7BFR Leitfaden

Summit

Summit FF-874 Series Bedienungsanleitung

Summit

Summit FFBF246SS Bedienungsanleitung

Summit

Summit CT66 Series Bedienungsanleitung

Summit

Summit FF6BISSHH Leitfaden

Summit

Summit FF1DSS Bedienungsanleitung

Summit

Summit CM405BI Bedienungsanleitung

Summit

Summit CM405 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung