Sun Oracle Sun Blade X6270 M2 Bedienungsanleitung

This guide describes the minimum steps you must perform to power on and configure your Sun Blade X6270 M2

Server Module for the first time.

Detailed installation information can be found in the Sun Blade X6270 M2 Server Module Installation Guide, which

is available at the Oracle documentation web site:

http://docs.sun.com/app/docs/prod/blade.x6270m2#hic

Contents

Oracle’s Sun Blade X6270 M2 Server Module is shipped with safety documentation and the components that you

ordered for your configuration. Optional components might be packaged and shipped separately.

Documentation and Media Kit

The Documentation and Media Kit is an orderable option for your system. It contains installation

documentation, the Tools and Drivers DVD, the Oracle Hardware Installation Assistant CD, and the Oracle

SunVTS CD. You can order the Documentation and Media Kit at any time, using the following marketing part

number: X6270-X-MEDDOCKIT.

You also can download the documentation and software that are included in the Documentation and Media Kit

from these sites.

■For documentation: http://docs.sun.com/app/docs/prod/blade.x6270m2#hic

■For software: http://www.oracle.com/goto/x6270m2

Safety and Compliance Information

Before performing an installation, refer to the following documents for safety information regarding the

Sun Blade X6270 M2 Server Module:

■Important Safety Information for Sun Hardware Systems – Printed document included in the ship kit.

■Sun Blade X6270 Server Module Safety and Compliance Manual – Online at the Oracle documentation site.

▼Install Optional Components

Before installing the server into the chassis, you must first install any optional components that you ordered

with the server, and that were not factory installed. Refer to the Sun Blade X6270 M2 Server Module Service Manual

for the instructions on installing optional components.

Sun Blade X6270 M2 Server Module

Getting Started Guide

▼Install Server Module and Verify STANDBY Power State

If inserted into a powered-on Sun Blade Modular System chassis, the server module, by default, receives

STANDBY power from the powered-on system chassis. For information about powering on the system chassis,

refer to the system chassis documentation. For more information about powering on the server module, refer to

the Sun Blade X6270 M2 Server Module Installation Guide. The following procedure assumes the chassis is

powered-on.

1. Verify that the system chassis is powered on.

When the chassis is powered on, the fans are operating and the OK/Power LED illuminates a STEADY ON

green light. The OK/Power LED is located on both the front and rear panels of the chassis.

2. At the front of the chassis, locate and remove the filler panel from the slot where you will insert the

server module. Pull the lever out and eject the filler panel.

3. Position the server module vertically so that the ejectors are on the right and extend outward.

4. Push the server module into the slot until the server module stops and is flush with the chassis.

5. To lock the server module into the chassis, rotate the top ejector down and the bottom ejector up until

both ejectors snap into place.

The ejectors are locked and STANDBY power is applied to the server module service processor (SP).

6. Verify STANDBY power state on the server module.

The server module SP can take several minutes to boot, during which the OK/Power LED on the server

module front panel illuminates a SLOW blink (0.5 second on, 0.5 second off). After the server module SP

boots, the OK/Power LED illuminates a STANDBY blink (0.1 second on, 2.9 seconds off). STANDBY blink

state indicates that STANDY power is supplied to the server module SP, the SP is active, and you can connect

to ILOM; however, the server module host is still powered off. Main power to the server module host must

be applied prior to installing an operating system.

▼Determine Your Method to Connect to ILOM

You can start, boot, and manage the server module using the Oracle Integrated Lights Out Manager (ILOM)

software (formerly called Sun Integrated Lights Out Manager software) that runs on the server module’s service

processor (SP). You can also control the server module from ILOM running on the chassis monitoring module

(CMM).

The table on the following page lists the methods you can use to connect to ILOM. This guide provides

instructions for the local serial connection (method 3).

To log in to ILOM remotely over an Ethernet network (method 1 in the table), you must know the IP address of

the server module SP or CMM. By default, the IP address for the server module is assigned by a DHCP server

(for IPv4 configurations) or an IPv6 router (for IPv6 configurations).

In a typical configuration, you will accept the IP address assigned by the DHCP server or IPv6 router. If you are

not using DHCP or an IPv6 router, or if you need to assign the server module SP a static IP address for any other

reason, refer to the Oracle Integrated Lights Out Manager (ILOM) 3.0 Documentation Collection for instructions.

You can connect to ILOM using one of the methods listed in the following table.

▼Connect to ILOM Using a Local Serial Connection

1. Verify that STANDBY power is supplied to the server module.

2. Insert the dongle cable into the universal port on the front panel of the server module, then attach the

RJ-45 or DB-9 connector to the serial terminal. Verify that the terminal has power and is operational.

3. Set the terminal to 9600 baud, 8 bit, no parity, 1 stop bit. A null modem connection is needed.

4. Press Enter on the terminal to connect the terminal device and the server module SP.

5. Log in to the ILOM CLI using the root user account and the root password, changeme.

The ILOM CLI prompt appears (->). You can now start, configure, and manage the server using ILOM.

(Connection Type)

Method From To Description

1(Ethernet)

CMM NET MGT

port

Your network Ensure that the chassis monitoring module (CMM) NET MGT port

is connected to your network.

From your network, log in to ILOM on the CMM or the server

module using the IP address of the CMM or server module. If you

are logged in to the CMM, use ILOM to navigate to the server

module SP ILOM interface. You can use the ILOM command-line

interface (as described in this guide), or use the ILOM web interface.

2 (Local Serial)

CMM SER MGT

port

Terminal device Connect a terminal device to the CMM SER MGT RJ-45 port and use

ILOM to navigate to the server module SP ILOM interface. This

method only supports the ILOM command-line interface.

3 (Local Serial)

Server module SP

UCP port

(dongle required)

Terminal device (Method used in this guide.)

Connect a dongle cable to the server module, and then connect a

terminal device to the RJ-45 or DB-9 connector on the dongle cable.

You can use the ILOM command-line interface as described in this

guide.

4 (Local KVM)

Server module SP

UCP port (dongle

required)

USB keyboard and

mouse, VGA monitor

Connect a dongle cable to the server module. Access the host by

connecting a keyboard and mouse to the dongle USB connectors

and a monitor to the HD15-pin VGA connector. Communicate with

ILOM on the server module SP through the host.

<hostname> login: root

Password: changeme

▼View or Change Network Settings Using the ILOM CLI

By default, the server module SP uses a Dynamic Host Configuration Protocol (DHCP) server for network

configuration of IPv4 networks and an IPv6 router for network configuration of IPv6 networks. To view the

default network settings using the ILOM CLI:

1. Navigate to the /network directory for IPv4 configuration or the /network/ipv6 directory for IPv6

configuration by typing one of the following commands.

2. To view the IPv4 or IPv6 network settings assigned to the server module, type the following command.

3. To configure static network settings or to change the IPv4 DHCP settings or IPv6 auto-configuration

options, refer to the Oracle Integrated Lights Out Manager (ILOM) 3.0 Documentation Collection.

▼Power On the Server Module Host

1. Power on the server module host by typing the following command and responding to the prompt.

The server module initializes. The server module might take several minutes to complete the power-on self-

test (POST). If a boot device installed with the Oracle Solaris OS is accessible locally, the server module

boots. Otherwise, the system uses the boot net command to seek a boot device on the network.

2. Switch communication to the console by typing the following command and responding to the prompt.

You are now connected to the server module host. The server module hardware installation is complete and

the server module is ready to be configured to suit your needs.

▼Upgrade Firmware

It is highly recommended that you use the Oracle Hardware Installation Assistant (formerly called Sun

Installation Assistant) to upgrade system BIOS and Oracle Integrated Lights Out Manager (ILOM) firmware. The

Hardware Installation Assistant is available in the Documentation and Media Kit, or online at:

http://www.oracle.com/goto/hia

For more information, refer to the Hardware Installation Assistant documentation at:

http://docs.sun.com/app/docs/prod/install.x64svr#hic

To upgrade system BIOS and ILOM firmware without using the Hardware Installation Assistant, refer to the

ILOM documentation for the version of ILOM supported for your server at:

http://docs.sun.com/app/docs/prod/blade.x6270m2#hic

All firmware and drivers are on the Tools and Drivers DVD, which is part of the Documentation and Media Kit.

You also can download the software on the Tools and Drivers DVD from the Oracle software download sites.

-> cd /SP/network

-> cd /SP/network/ipv6

-> show

-> start /SYS

Are you sure you want to start /SYS (y/n)? y

Starting /SYS . . .

-> start /SP/console

Are you sure you want to start /SP/console (y/n)? y

Serial console started. To stop, type #.

▼Set Up the Platform Operating System and Driver Software

After configuring the ILOM SP with network settings, you can configure a preinstalled or supported OS.

Hardware Warranty and Software Service Plan

For information on hardware warranty, see: http://www.sun.com/service/warranty/index.jsp

For information on a software service plan, see: http://www.oracle.com/support/premier/index.html

If you need service for your system, you might be asked for your hardware serial number. To find the serial

number of your system, use the ILOM command show /SYS, or see your Installation Guide or Service Manual

for information about where to find the serial number label.

Operating

system: Read this document:

For installation information,

go to:

For tools, drivers,

firmware, Hardware

Installation

Assistant, go to:

For patch information,

go to:

Preinstalled

operating

system

Sun Blade X6270 M2 Server

Module Installation Guide

http://

www.oracle.com/

goto/x6270m2

• http://

www.oracle.

com/goto/

blades

• See the Sun Blade X6270

M2 Server Module

Product Notes

• http://

support.oracle.com

Oracle

Solaris

Sun Blade X6270 M2 Server

Module Installation Guide

for Linux, Virtual Machine

Software, and Oracle Solaris

Operating Systems

http://

www.oracle.com/

goto/x6270m2

Oracle VM http://

www.oracle.com/

virtualization/

http://

www.oracle.com/

virtualization/

VMware http://

www.vmware.com

http://

downloads.vmware.com

Windows • Windows or Linux: Sun

Installation Assistant 2.3

through 2.4 User’s Guide

for x64 Servers

•Windows: Sun Blade

X6270 M2 Server Module

Installation Guide for

Windows Operating

Systems

•Linux: Sun Blade X6270

M2 Server Module

Installation Guide for

Linux, Virtual Machine

Software, and Oracle

Solaris Operating Systems

• http://

www.oracle.com/

goto/hia

• http://

www.oracle.com/

goto/x6270m2

•Windows or

Linux: Use the

Hardware

Installation

Assistant for

automatic

firmware

update and

driver

installation

http://

update.microsoft.

com/

Linux • Redhat: https://

www.redhat.com/

apps/download/

• SUSE: http://

download.novell.

com/index.jsp

Accessing Documentation

You can view and print documentation for Oracle’s servers at:

http://docs.sun.com

Contacting Technical Support

If you have technical questions about this product that are not answered in this document, go to:

http://www.sun.com/service/contacting

Documentation Comments

Submit comments about this document by clicking the Feedback[+] link at:

http://docs.sun.com

Please include the title and part number of your document with your feedback:

Sun Blade X6270 M2 Server Module Getting Started Guide, part number 821-0494-13

Task Document Type*

* For translated versions of some documents, go to http://www.sun.com and select your language.

Part Number

Review safety information. Safety and Compliance Manual 821-0500

Important Safety Information for Sun Hardware 821-1590

Review known issues and workarounds. Product Notes 821-0496

Install, power on, and configure the preinstalled OS. Installation Guide 821-0495

Configure and manage RAID arrays. x64 Servers Utilities Reference Manual 820-1120

Install and configure the Oracle Solaris, Linux,

Windows OS, or install virtual machine software

such as Oracle VM or VMware.

Linux, Virtual Machine Software, and Oracle Solaris

OS Installation Guide

821-0497

Windows OS Installation Guide 821-0498

Manage server accounts, monitor alerts, set remote

access and redirection, and view component status.

Oracle ILOM 3.0 Documentation:

http:docs.sun.com/app/docs/prod/

int.lights.mgr30#hic

Multiple

documents

Customize BIOS and RAID settings. Remove and

replace components. Troubleshoot server problems.

Service Manual 821-0499

Bar Code Area

Part No. 821-0494-13, Rev. A

October 2010

Inhaltsverzeichnis

Andere Sun Oracle Server Handbücher

Sun Oracle

Sun Oracle Sun Blade 6000 Technisches Handbuch

Sun Oracle

Sun Oracle Fire X4440 Bedienungsanleitung

Sun Oracle

Sun Oracle T5220 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X6270 M3 Installations- und Betriebsanleitung

Sun Oracle

Sun Oracle T5120 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Ray 3i Client Bedienungsanleitung

Sun Oracle

Sun Oracle 4540 - Phaser Copystation Bedienungsanleitung

Sun Oracle

Sun Oracle Netra 6000 Bedienungsanleitung

Sun Oracle

Sun Oracle X3-2 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle Netra SPARC T3-1BA Installations- und Betriebsanleitung

Sun Oracle

Sun Oracle Netra SPARC T3-1B Service-Handbuch

Sun Oracle

Sun Oracle Fire X4470 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC Enterprise M9000 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T4-1 Bedienungsanleitung

Sun Oracle

Sun Oracle X3-2L Technisches Handbuch

Sun Oracle

Sun Oracle SPARC T4-4 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC SuperCluster T4-4 Installations- und Betriebsanleitung

Sun Oracle

Sun Oracle Netra X6270 M3 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade T6340 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Server X4-2 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung