Sun Oracle Sun Server X4-2L Bedienungsanleitung

This guide describes the minimum steps you must perform for initial installation and power-on of the server.

For detailed installation information, refer to the Sun Server X4-2L Installation Guide. You can access the product

documentation using Oracle System Assistant and at the Oracle documentation website.

Before You Begin

■If you are deploying multiple servers, use Oracle Enterprise Manager Ops Center. Refer to the Oracle

Enterprise Manager Ops Center product documentation at:

http://docs.oracle.com/cd/E27363_01/index.htm

■If you are deploying a single server, use Oracle System Assistant, which is embedded in the Sun Server X4-2L.

For information about Oracle System Assistant, refer to the Oracle x86 Administration Guide for X4 Series

Servers at:

http://www.oracle.com/goto/x86AdminDiag/docs

Installing the Server

The following steps describe basic installation tasks for the server:

“1. Review Product Documentation” on page 1

“2. Install Optional Components” on page 2

“3. Mount the Server Into a Rack” on page 2

“4. Connect the Cables and Power Cords” on page 3

“5. Set Up Software and Firmware Using Oracle System Assistant” on page 4

“6. Set Up an Operating System and Drivers” on page 5

▼1. Review Product Documentation

1. Before installing the server, refer to the online Sun Server X4-2L Documentation Library. The most up-to-

date documents, including translations of some of the documents, are available at:

http://www.oracle.com/goto/X4-2L/docs

Sun Server X4-2L

Getting Started Guide

Oracle is interested in improving its documentation and welcomes your comments and suggestions. You can

submit comments at: http://www.oracle.com/goto/docfeedback

▼2. Install Optional Components

Optional components for your server might be packaged and shipped separately. If applicable, install optional

components (such as DIMMs or storage drives) before mounting the server in a rack.

1. For installation procedures for optional components, refer to the Sun Server X4-2L Service Manual.

2. For a complete list of optional components, refer to the Sun Server X4-2L product page at:

http://www.oracle.com/goto/X4-2L

▼3. Mount the Server Into a Rack

For rackmounting instructions:

♦Refer to the documents included with the rail kit, the service label on the server, and the Sun Server X4-2L

Installation Guide.

Refer To: Information

Sun Server X4-2L Safety and Compliance Guide Safety precautions and procedures specific to the Sun Server X4-2L.

Important Safety Information for Oracle’s Hardware

Systems

Safety precautions and procedures to follow when installing Oracle

hardware.

Sun Server X4-2L Product Notes Supported software and hardware, and known server issues.

Sun Server X4-2L Installation Guide How to install hardware, cable and power on the server, connect to the

service processor (SP), launch Oracle System Assistant, and configure

network settings.

Sun Server X4-2L operating system installation

guides

How to install supported operating systems, including Oracle Solaris,

Oracle VM, Oracle Linux and other Linux systems, Windows, or

VMware ESXi.

Sun Server X4-2L Service Manual How to install optional components, remove and replace hardware

components, and troubleshoot server problems.

Oracle x86 Administration Guide for X4 Series

Servers

Software methods to set up the server using Oracle System Assistant,

Oracle ILOM, and Oracle Hardware Management Pack. Refer to:

http://www.oracle.com/goto/x86AdminDiag/docs

Oracle recommends using Oracle System Assistant to set up the server.

You can also use Oracle ILOM and Oracle Hardware Management

Pack for some setup tasks.

Oracle Integrated Lights Out Manager (ILOM)

Documentation Collection

Oracle ILOM features and how to perform server configuration,

monitoring, and administration tasks using Oracle ILOM. Refer to:

http://www.oracle.com/goto/ILOM/docs

▼4. Connect the Cables and Power Cords

Use Oracle System Assistant to simplify the setup and configuration of the server. For instructions, see “5. Set

Up Software and Firmware Using Oracle System Assistant” on page 4. Alternatively, you can use Oracle ILOM

for some server setup and configuration tasks. For instructions, refer to the Oracle ILOM Documentation

Collection.

Caution – Do not apply power to the server until instructed to do so. The server includes a service

processor (SP) that is used to configure and boot the host system. To properly configure the host

system and view SP messages, do not apply power to the server until you make the SP and host

networking connections, as described in this section.

To locate the server cable connections, see “Cabling Diagram” on page 4.

1. (Recommended method) To cable the server for local connection to Oracle System Assistant:

a. Connect a VGA monitor to the VGA port on the server.

b. Connect a USB keyboard and mouse to the USB connectors on the server.

2. (Alternative method) To cable the server for connection to Oracle ILOM:

a. For a local serial connection – Connect a serial cable between the server’s serial management port

(SER MGT) and a terminal device.

This connection provides initial communication with the SP. Set the server to communicate using 9600

baud, 8 bit, no parity, 1 stop bit. For DTE-to-DTE communication, use the supplied RJ-45 crossover

adapter with a standard RJ-45 cable to set up a null modem connection (transmit and receive signals

crossed over).

b. For a remote Ethernet connection – Connect an Ethernet cable between the server’s network

management port (NET MGT) and the network to which future connections to the SP and host will

be made.

If using Oracle ILOM, configure the system for the first time through the SER MGT port. After initial

configuration, you can set up communication between the SP and host through the remote Ethernet

interface.

3. For network access, connect an Ethernet cable between the server’s NET ports (NET3-0) and the network

to which the server will communicate.

4. Connect the power cords to the power supplies and to separate power sources.

The server is equipped with two power supplies. Connect them to separate power sources to provide power

redundancy. The server can operate with one power source; however, having only one power source reduces

the redundancy.

When the power cords are connected, the power supply LEDs light and the SP OK LED will blink rapidly as

the SP boots. The SP OK LED will light solid green once the SP has booted. After the SP has booted, the

Power/OK LED on the front panel will blink slowly, indicating that the host is in standby power mode. In

standby power mode, the server is not yet initialized or powered on.

Cabling Diagram

FIGURE 1 Cabling for the Sun Server X4-2L

▼5. Set Up Software and Firmware Using Oracle System Assistant

Oracle System Assistant enables you to update to the latest available firmware and software, easily configure

key server settings, and install an Oracle VM, Linux, or Windows operating system. This is the easiest method

for setting up the server. Oracle System Assistant is embedded in most Sun Server X4-2L systems.

1. Verify that the server is correctly installed in the rack.

2. Verify that a local console connection has been made to the server for Oracle System Assistant;

see “4. Connect the Cables and Power Cords” on page 3.

■VGA monitor is connected to the VGA port on the server.

■Keyboard and mouse are connected to the USB connectors on the server.

3. Verify that the server is in standby power mode; see “4. Connect the Cables and Power Cords” on page 3.

4. Launch Oracle System Assistant.

a. Press the front panel Power button to power on the server to full power mode.

The server boots, and power-on self-test (POST) and boot messages appear on the monitor.

Be attentive: You need to interrupt the boot process.

b. When prompted in the initial BIOS screen, press the F9 key.

The Oracle System Assistant application boots and the System Overview screen appears, showing system

information, and task buttons in the left pane.

Figure Legend

1Power supply 0 input power

Power supply 1 input power

4Ethernet ports (NET 3, NET 2, NET 1,

NET 0)

7Video port (VGA)

2Network management port (NET MGT) 5USB port (USB 0)

3Serial management port (SER MGT) 6USB port (USB 1)

Note – You can also access Oracle System Assistant using the Oracle ILOM Remote Console. This access method

requires setting up a connection to Oracle ILOM and accessing the host console using an Oracle ILOM web

connection. Refer to the Oracle x86 Administration Guide for X4 Series Servers for instructions.

5. To set up the server’s network connection, click Configure Network.

6. To download the latest server firmware and software, click Get Updates.

7. To update the Oracle ILOM, BIOS, disk expander, or host bus adapter (HBA) firmware on the server, click

Update Firmware.

8. To configure Oracle ILOM, click Configure Hardware > Service Processor Configuration.

9. To configure RAID, click Configure Hardware > RAID Configuration.

10. To install an Oracle VM, Linux, or Windows operating system, and also download and install system

drivers and firmware, click Install OS.

For information on other supported OS installation options, see “6. Set Up an Operating System and

Drivers” on page 5.

▼6. Set Up an Operating System and Drivers

♦Use the options in the following table to set up a supported operating system (OS) and required drivers.

If you do not have access to Oracle System Assistant to install drivers, you can download the latest Sun Server

X4-2L software release from the My Oracle Support website at: http://support.oracle.com

OS Setup Option Refer To:

Configure preinstalled Oracle Solaris,

Oracle VM, or Oracle Linux

Sun Server X4-2L Installation Guide

Install OS: Oracle VM, Linux, or Windows Use Oracle System Assistant (recommended) or refer to the installation guide

for the OS

Install Oracle Solaris OS Sun Server X4-2L Installation Guide for Oracle Solaris Operating System

Install VMware ESXi software Sun Server X4-2L Installation Guide for VMware ESXi

Install supported OS drivers Use Oracle System Assistant (recommended) or refer to the installation guide

for the OS

Server Front Panel Components

FIGURE 2 Sun Server X4-2L Front Panel Components

Access to Oracle Support

Oracle customers can access electronic support through My Oracle Support at http://support.oracle.com.

For detailed information, visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=info or if you

are hearing impaired, visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs.

The server serial number, which you will need when requesting service or technical support, is on the front

panel of the system and on the Customer Information Sheet that is shipped with the system. You can also view

the serial number using Oracle ILOM or Oracle System Assistant.

Figure Legend

1Locator LED/Locator button: white 7Storage disk drive 1 (optional) 13 Storage disk drive 7 (optional)

2Service Required LED: amber 8Storage disk drive 2 (optional) 14 SATA DVD drive

3Power/OK LED: green 9Storage disk drive 3 (optional) 15 Service Required LEDs (3):

Top: Fan Module (amber)

Rear: Power Supply (amber)

Overtemp Icon: System Over

Temperature Warning (amber)

4Power button 10 Storage disk drive 4 (optional) 16 USB 2.0 connectors (2)

5SP OK LED: green 11 Storage disk drive 5 (optional)

6Storage disk drive 0 (optional) 12 Storage disk drive 6 (optional)

Part No.: E36973-02

Mfg No.: 7060265

September 2013

Inhaltsverzeichnis

Andere Sun Oracle Server Handbücher

Sun Oracle

Sun Oracle Netra 6000 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle T5120 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC SuperCluster T4-4 Installations- und Betriebsanleitung

Sun Oracle

Sun Oracle Sun Netra T5440 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T4-4 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun X2-8 Bedienungsanleitung

Sun Oracle

Sun Oracle T5120 Bedienungsanleitung

Sun Oracle

Sun Oracle Blade X4-2B Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC Enterprise M9000 Bedienungsanleitung

Sun Oracle

Sun Oracle X4270 M2 Bedienungsanleitung

Sun Oracle

Sun Oracle Netra SPARC T3-1B Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle Netra X6270 M3 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Server X4-2 Bedienungsanleitung

Sun Oracle

Sun Oracle Netra X4250 Technisches Handbuch

Sun Oracle

Sun Oracle NETRA SPARC T4-1 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T3-2 Bedienungsanleitung

Sun Oracle

Sun Oracle Netra SPARC T3-1B Service-Handbuch

Sun Oracle

Sun Oracle X3-2L Technisches Handbuch

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun SPARC Enterprise M3000 Service-Handbuch

Sun Oracle

Sun Oracle Netra SPARC T3-1BA Installations- und Betriebsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung