Sun Oracle T5120 Bedienungsanleitung

This guide describes the minimum steps you must perform to power on and boot Oracle’s Sun SPARC

Enterprise T5120 server for the first time using the preinstalled Oracle Solaris™ Operating System (Solaris OS).

Servers that use DC input power require you to build and connect the power cords to specific safety

specifications. The specifications are described in the Sun SPARC Enterprise T5120 and T5220 Servers Installation

Guide that is available from http://docs.sun.com/app/docs/prod/sparc.t5120.

FIGURE 1 Sun SPARC Enterprise T5120 Server

Shipping Contents

Before You Begin

For quick installation and configuration, follow these steps. For more detailed information, refer to the complete

online product documentation set at: http://docs.sun.com/app/docs/prod/sparc.t5120

Understand the following information before you set up the server for the first time:

■Do not apply power until instructed to do so – This system includes a service processor (SP) that is used to

configure and boot the host server. To properly configure the host server and view SP messages, do not apply

power to the server until the SP and host networking connections are made, as described in this guide.

■Choose the best instructions for your situation – The quick setup instructions in this guide work for any

networking environment, and require the use of a terminal device for connection to a serial port. If you have

a networking environment running DHCP, you can configure your system using the Ethernet management

port. To take advantage of the DHCP setup method, refer to the online installation guide in the online product

documentation set at: http://docs.sun.com/app/docs/prod/sparc.t5120

Quantity Item

1 Server

2 RJ-45 Ethernet cable

1 RJ-45 to DB-25 adapter (crossover)

1 RJ-45 to DB-9 adapter (crossover)

2 DC power connectors

Sun SPARC Enterprise T5120 Server

Getting Started Guide (For Models That Run on DC Input Power)

■Set aside sufficient time – Installation times vary, but if you are performing these setup instructions for the

first time, plan to spend about 45 to 75 minutes to complete all of these instructions. Additional time might be

required for installing optional hardware and rackmounting kits.

■Obtain a terminal device – You configure this rackmountable server through the SP using the built-in serial

and network management ports, and not through a graphical interface and Sun keyboard. To communicate

with the SP, you will need a terminal device, which can be a terminal, terminal server, or laptop running

terminal emulation software.

■Gather your configuration information – During the configuration, you are prompted for time zone and

networking parameters for your environment.Use TABLE 1 to record your configuration information.

TABLE 1 Configuration Information

Parameter Description Your Entry

Language Select a number from the displayed language list.

Locale Select a number from the displayed locale list.

Terminal Type Select a terminal type that corresponds with your terminal device.

Network? Select Yes.

Multiple Network

Interfaces

Select the network interfaces that you plan to configure. If you are not sure,

select the first one in the list.

DHCP? Select Yes or No according to your network environment.

Host Name Enter the host name for the server.

IP Address Enter the IP address for the selected Ethernet interfaces.

Subnet? Select Yes or No according to your network environment.

Subnet Netmask (If subnet was Yes) Enter the netmask for the subnet for your network

environment.

IPv6? Specify whether or not to use IPv6. If you are not sure, select No to

configure the Ethernet interface for IPv4.

Security Policy Select either standard UNIX security (No) or Kerberos Security (Yes). If you

are not sure, select No.

Confirm Review the onscreen information and change it if needed. Otherwise,

continue.

Name Service Select the name service according to your network environment.

Note – If you select a name service other than None, you will be prompted

for additional name service configuration information.

NFSv4 Domain

Name

Select the type of domain name configuration according to your

environment. If you are not sure, select Use the NFSv4 domain derived

by the system.

Time Zone

(Continent)

Select your continent.

Time Zone

(Country or Region)

Select your country or region.

Quick Setup Instructions

1. Unpack the server, and check that you received all of the shipping contents.

2. Place the server in its intended location for verification.

For rackmounting instructions, refer to the instructions included with the rail kit, the service label on the

server, and to the online Sun SPARC Enterprise T5120 and T5220 Servers Installation Guide.

3. Connect a serial cable between the server’s SER MGT port (FIGURE 2) and a terminal device.

This connection provides your initial communication with the SP.

The device must be set up to communicate using 9600 baud, 8 bit, no parity, 1 stop bit. A null modem

configuration is needed, meaning the transmit and receive signals are reversed (crossed over) for DTE to

DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45 cable to

achieve the null modem configuration.

Time Zone Select the time zone.

Date and Time Accept the default date and time, or change the values.

root Password Enter the root password twice. This password is for the superuser account

for the Solaris OS on this server. This password is not the SP password.

TABLE 1 Configuration Information (Continued)

FIGURE 2 Server Connections

4. (Optional) Connect an Ethernet cable between the server’s NET MGT port (FIGURE 2) and the network to

which future connections to the SP and host will be made.

After the initial configuration of the system using the SER MGT port, communication with the SP and host is

usually performed through this Ethernet interface.

5. Connect an Ethernet cable between one of the server’s NET ports (FIGURE 2) and the network to which the

server will communicate.

6. Build and connect your DC power cables into the server power supplies and into separate power sources.

Instructions for building the DC power cables are in the SPARC Enterprise T5120 and T5220 Servers Installation

Guide.

To provide redundancy, plug both power supplies into separate power sources. Note that the system can

operate with only one power connection, but there is no redundancy in this case.

When power is applied, the SP initializes and power supply LEDs illuminate. After a few minutes, the SP

7. At the terminal device, log in to the SP as root with a password of changeme.

After a brief delay, the SP prompt is displayed (->).

At this point, there are many commands you can perform using the Integrated Lights Out Manager interface.

For example, to create a user named admin, and to set the admin account role to Administrator and the

CLI mode to alom, enter:

Note that the asterisks in the example will not appear when you enter your password.

Additional SP information, such as how to change the password and how to set up the SP network

parameters, is available in the online documentation set.

8. Power on the server and redirect the host output to display on the serial terminal device:

After you start the SP console, the server initialization takes approximately 20 minutes to complete.

9. When prompted, follow the onscreen instructions and enter the configuration information.

Refer to TABLE 1 for the list of configuration information and your entries. You will be prompted to confirm

the configuration several times, enabling confirmation and changes. If you are not sure how to respond to a

particular value, you can accept the default, and make future changes when the Solaris OS is running.

When the configuration menus are completed, the server reboots and displays the Solaris login prompt.

10. Log in to the server and explore the capabilities.

The following commands provide information about the system:

■showrev – Displays the hostname and system architecture information. Use the -a option with this

command to see the patches that are installed.

■psrinfo – Displays information about the number and status of the processors and cores in the host.

Review the Solaris OS man pages and documentation for more details.

SUNSP00144FAC732F login: root

Password: changeme

. . .

-> create /SP/users/admin role=Administrator cli_mode=alom

Creating user...

Enter new password: ********

Enter new password again: ********

Created /SP/users/admin

-> start /SYS

Are you sure you want to start /SYS (y/n)? y

-> start /SP/console

Are you sure you want to start /SP/CONSOLE (y/n)? y

Serial console started. To stop, type #.

. . .

Accessing Additional Information

You can view, print, and download additional information for this product from the following URLs:

■Oracle’s Sun SPARC Enterprise T5120 server documentation set, including important documents such as

product notes:

http://docs.sun.com/app/docs/prod/sparc.t5120

■A broad selection of Sun documentation, including localized versions:

http://docs.sun.com

■Preinstalled Solaris™OS information:

http://www.sun.com/software/preinstall

■CoolThreads™– Overview and access to Cool Tools:

http://www.sun.com/servers/coolthreads/tnb/index.jsp

■CoolThreads – CMT tuning and resources:

http://www.sun.com/servers/coolthreads/tnb/t2.jsp

Technical Support

If you have technical questions about this product that are not answered in this document, go to:

http://www.sun.com/service/contacting

Documentation Feedback

Submit comments about this document by clicking the Feedback[+] link at:

http://docs.sun.com/

Please include the title and part number of your document with your feedback:

Sun SPARC Server Enterprise T5120 Server Getting Started Guide (DC Models), part number 820-5838-11

Part No. 820-5838-11, Rev. A

July 2010

Andere Handbücher für T5120

Inhaltsverzeichnis

Andere Sun Oracle Server Handbücher

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle X4170 M2 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X3-2B Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle T5120 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Fire X4800 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun SPARC Enterprise T5140 Bedienungsanleitung

Sun Oracle

Sun Oracle X4270 M2 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun SPARC Enterprise T5140 Bedienungsanleitung

Sun Oracle

Sun Oracle Fire X4470 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Ray 3i Client Bedienungsanleitung

Sun Oracle

Sun Oracle X3-2 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade 6048 Service-Handbuch

Sun Oracle

Sun Oracle T5220 Bedienungsanleitung

Sun Oracle

Sun Oracle BLADE T6320 Bedienungsanleitung

Sun Oracle

Sun Oracle T4BLD Installations- und Betriebsanleitung

Sun Oracle

Sun Oracle Fire X4470 Bedienungsanleitung

Sun Oracle

Sun Oracle Netra X6270 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Blade X6270 M2 Bedienungsanleitung

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun Netra T5440 Bedienungsanleitung

Sun Oracle

Sun Oracle Sun SPARC Enterprise M3000 Service-Handbuch

Sun Oracle

Sun Oracle SPARC T3-1 Bedienungsanleitung

Sun Oracle

Sun Oracle SF2EP Installations- und Betriebsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung