Sunbeam HE2100 Bedienungsanleitung

Please read these instructions carefully and

retain for future reference.

Compact Ceramic

Oscillating Heater

1800W oscillating heater with ceramic element

Instruction Booklet

HE2100

Contents

Sunbeam’s Safety Precautions 1

Sunbeam’s Safety Precautions for your Heater 2

Sunbeam’s Total Safety System 3

Features of your Compact Oscillating

Ceramic Heater 4

Using your Compact Oscillating

Ceramic Heater 6

Using the Oscillation function 7

Resetting the Total Safety System 7

Troubleshooting Guide 8

Care and Cleaning 8

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

Sunbeam are very safety conscious when

designing and manufacturing consumer products,

but it is essential that the product user also

exercise care when using an electrical appliance.

Listed below are precautions which are essential

for the safe use of an electrical appliance:

• Read carefully and save all the instructions

provided with an appliance.

• Always turn the power off at the power outlet

before you insert or remove a plug. Remove

by grasping the plug - do not pull on the cord.

• Turn the power off and remove the plug

when the appliance is not in use and

before cleaning.

• Do not use your appliance with an extension

cord unless this cord has been checked

and tested by a qualified technician or

service person.

• Always use your appliance from a power

outlet of the voltage (A.C. only) marked

on the appliance.

• This appliance is not intended for use by young

children or infirm persons unless they have

been adequately supervised by a responsible

adult to ensure that they can use the appliance

safely.

• Young children should be supervised to ensure

that they do not play with the appliance.

• Never leave an appliance unattended while

in use.

• Do not use an appliance for any purpose

other than its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang

over the edge of a table or bench top or touch

any hot surface.

• For safety reasons and to avoid maintenance

by unskilled persons, some appliances are

‘sealed’ using tamperproof screws. Such

appliances should always be returned to the

nearest Sunbeam Appointed Service Centre

for adjustment or repair if required.

• Do not operate any electrical appliance with

a damaged cord or after the appliance has

been damaged in any manner. If damage is

suspected, return the appliance to the nearest

Sunbeam Appointed Service Centre

for examination, repair or adjustment.

• For additional protection, Sunbeam

recommend the use of a residual current

device (RCD) with a tripping current not

exceeding 30mA in the electrical circuit

supplying power to your appliances.

• Do not immerse the appliance in water

or any other liquid unless recommended.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Sunbeam’s Safety Precautions

• This heater becomes hot during use. To avoid

burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this

heater. Keep combustible materials such as

furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (90cm) away from the

front of the heater and keep them away from

the sides and rear.

• Extreme caution is necessary when any heater

is used by or near children or invalids and

whenever the heater is left unattended.

• Always unplug the heater when not in use.

• Do not use outdoors.

• Do not run the cord of the heater under

carpeting. Do not cover the cord with throw

rugs, runners or other floor coverings. Arrange

the cord away from traffic areas where it will

not be tripped over.

• Do not locate the heater immediately below a

socket outlet.

• Do not use this heater in the immediate

surrounds of a bath, shower, laundry area or

swimming pool.

• Do not insert or allow foreign objects to enter

any ventilation or exhaust openings as this may

cause electric shock or fire, or damage to the

heater.

• To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use

on soft surfaces, such as beds, where opening

may become blocked.

• A heater has hot and arcing or sparing parts

inside. Do not use it in areas where petrol,

paint or flammable liquids are used or stored.

• To prevent overheating, do not cover the

heater.

Important instructions – retain for

future use.

Safety auto shut off

Your Sunbeam Compact Oscillating Ceramic

heater is equipped with a safety system that

detects any abnormally high temperatures

within the heater and automatically shuts it

off to prevent overheating. If the heater is

getting excessively hot, an alarm will sound.

Do not operate the heater with the alarm

sounding. Immediately turn the heater off at

the power outlet and check that there aren't

any objects on or around the heater.

This first stage of the safety system requires

the user to manually reset the heater for it to

resume operation.

For instructions on how to reset your heater,

see page 7.

Thermal back-up device

In addition to this automatic shut-off, your

heater contains an over temperature thermal

back-up device to provide additional back-

up protection. If the heater is in an overheat

situation, the back-up device will operate,

stopping the power flow to the element and

fan.

In the event that the back-up device is

activated, the heater will need to be reset.

For instructions on how to reset your heater,

see page 7.

Sunbeam’s Total Safety System

Mode button

Press the mode button to select the desired

operating mode:

LOW HEAT, HIGH HEAT

AUTO, FAN or STANDBY

Fan setting

Ideal for circulating cool air in summer, the fan

setting operates the fan without heat.

Power ON light

Illuminates to indicate that the heater is

connected to the power outlet.

LCD screen

The LCD screen displays the current settings

including the ambient room temperature, the

selected mode, or heat setting.

Safety auto shut-off

The safety auto shut-off system detects any

abnormally high temperature variations within

the heater and automatically switches it off to

prevent overheating.

Features of your Compact

Oscillating Ceramic Heater









Oscillation function

The heater oscillates 90 degrees to provide

greater heat distribution. Simply press the

oscillation button (OSC) to activate this

function.

Electronic thermostat

The electronic thermostat allows for precise

temperature control. Select the auto mode

to set the electronic thermostat and turn the

thermostat dial to the desired heat setting.

Once your desired temperature is reached,

the heater will cycle on and off to maintain

it.

Thermostat dial

When in auto mode, turn the thermostat dial

to select your desired temperature.

Ceramic element

The 1800 watt ceramic element is more

efficient than other element types as it

converts more electricity into heat.

Ceramic elements are also safer than other

element types. They do not glow and operate

at such low temperatures that they will not

ignite even highly flammable materials such

as tissue paper.









1. Place the heater on a flat level surface and

ensure that the air intake and outlet are

clear of obstructions.

2. Insert the plug into a 230/240V power

outlet and turn the power on.

3.The power on light and LCD screen will

illuminate.

NOTE: When the heater is switched on it

will be automatically set to the Standby

mode.

4. Press the mode button to select the

desired setting, as follows. Each time you

press the mode button it will scroll through

the various settings.

LOW – low heat setting

HIGH – high heat setting

AUTO – for operating the electronic

thermostat

FAN – for fan only operation

without heat

STANDBY – the heater remains inactive

when in this mode

NOTE: The fan speed will not change when

the mode is changed from low to high.

5. To switch the heater off, press the mode

button until the standby mode is set and

switch the power off at the power outlet.

Setting the electronic thermostat

The electronic thermostat allows you to set

the precise temperature. Once the desired

temperature level is reached the heater will

cycle on and off to maintain it.

1. Press the mode button until the AUTO

mode is displayed. The LCD screen will

display the ambient room temperature.

2. Set the desired temperature by turning the

thermostat dial. The selected temperature

will appear on the LCD screen.

NOTE: The temperature range is from

15ºC to 30ºC.

3. When the room temperature reaches

the set temperature the heater will

automatically turn off. The fan will

continue running for 15 seconds to cool

the heater. The unit will only turn on when

the room temperature falls below the

preset temperature.

NOTE: It is normal for the heater to cycle

on and off as it maintains the preset

temperature. To prevent the unit from

cycling, raise the thermostat setting.

Using your Compact Oscillating

Ceramic Heater

Using the Oscillation Function

The 90 degree oscillation function can be

used in any mode except standby.

1. Press the oscillation button (OSC),

positioned on the top of the heater. The

heater will then begin to oscillate from side

to side.

2. To stop the heater from oscillating, simply

press the oscillation button (OSC) once

again.

Resetting the Total Safety System

Resetting the safety auto shut-off

The safety auto shut-off detects any

abnormally high temperatures within the heater

and shuts it off to prevent overheating. Should

the safety auto shut-off activate and switch off

the heater, it will need to be reset.

1. To reset the heater, press the mode button

until the standby mode is selected.

2. Unplug the heater and wait 10 minutes for

the unit to cool down.

3. After 10 minutes, plug the heater in again

and operate as usual.

Resetting the thermal backup device

In addition to the safety auto shut-off, your

heater also contains a thermal back-up

device for additional protection. Should the

thermal back-up device activate and switch

off the heater it will need to be reset.

To reset the heater, follow steps 1 to 3 on

this page.

If your heater fails to operate check the

following:

• Make sure the electrical outlet or circuit

breaker is working.

• Check for obstructions. If you find an

obstruction, turn the heater off and follow

the reset instructions on page 7.

• Check that the thermostat is not set too

low. Turn the thermostat dial clockwise to

adjust the electronic thermostat until the

heater restarts.

• The safety auto shut-off may have

activated, so follow the instructions for

resetting on page 7.

Troubleshooting Guide

Ensure that the heater is switched off and

disconnected from the power outlet before

cleaning.

Carefully wipe the exterior of the heater with

a soft damp cloth and dry thoroughly with a

dry cloth.

Over time, dust may accumulate on the front

grilles. This can be removed by wiping with a

damp cloth.

Store the heater in a cool dry place when

not in use. Store the heater in its carton if

possible.

Care and Cleaning

Inhaltsverzeichnis

Andere Sunbeam Heizung Handbücher

Sunbeam

Sunbeam HE2050 Bedienungsanleitung

Sunbeam

Sunbeam SFH400 Bedienungsanleitung

Sunbeam

Sunbeam Micro Furnace MF2000 Bedienungsanleitung

Sunbeam

Sunbeam SFH436-CN Handbuch

Sunbeam

Sunbeam SCH4062 Bedienungsanleitung

Sunbeam

Sunbeam SCH160-CN Handbuch

Sunbeam

Sunbeam SFH442 Bedienungsanleitung

Sunbeam

Sunbeam HE4100 Bedienungsanleitung

Sunbeam

Sunbeam SEH8001 Handbuch

Sunbeam

Sunbeam MF1500 1500W Bedienungsanleitung

Sunbeam

Sunbeam Steam Master Bedienungsanleitung

Sunbeam

Sunbeam SFH5963M Bedienungsanleitung

Sunbeam

Sunbeam HE2105 Bedienungsanleitung

Sunbeam

Sunbeam Heater Calefactor Bedienungsanleitung

Sunbeam

Sunbeam SCH4015 Series Bedienungsanleitung

Sunbeam

Sunbeam HE3100 Bedienungsanleitung

Sunbeam

Sunbeam SFH610 Bedienungsanleitung

Sunbeam

Sunbeam HE4900 Bedienungsanleitung

Sunbeam

Sunbeam SCH8305 Series Handbuch

Sunbeam

Sunbeam Smartheat HE6100 Bedienungsanleitung

Sunbeam

Sunbeam SCH160 Handbuch

Sunbeam

Sunbeam SFH436-UM Handbuch

Sunbeam

Sunbeam Calefactor SFH612 Bedienungsanleitung

Sunbeam

Sunbeam HE2300 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung