Sundstrom SR 590 Bedienungsanleitung

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

1 of 22

Operating Instruction

SR 590 Welding shield

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

2 of 22

General information

The Sundström SR 590 welding shield is used together with the

Sundström SR 500 battery-powered fan unit and is designed

for protecting the user against inhaling harmful and irritating air

pollutants and against radiation and weld spatter during arc

welding, MAG welding and TIG welding.

SR 590 is in one size.

The SR 590 welding shield together with fan SR 500 is approved in

accordance with EN 12941:1998, TH3.

When selecting equipment for SR 590 some of the factors that

should be taken into account are as follows:

•Type of pollutant

•Concentrations

•Work intensity

•Protection requirements in addition to respiratory protective advice.

Risk analysis should be carried by a person who has suitable

training and experience in the area.

Instructions for use for SR 590 should be read before use.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

3 of 22

4.1 Check flow

Before the check, also read the user

instructions for fan SR 500.

Start fan the fan

Connect the hose from the visor to the

fan unit (or compressed air equipment)

turn the coupling 1/8 of a turn.

Place the head top in the flow meter and

start the fan unit.

Grip the lower part of the bag to seal

around the breathing hose.

Grip the flow meter tube with the other

hand so that the tube points vertically

upwards from the bag.

Read the position of the ball in the tube.

This should hover at a level with or

slightly above the upper marking on the

tube.

If minimum flow is not achieved,

check that:

–The flow meter is held upright.

–The ball moves freely.

–The bag seals well around the hose.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

4 of 22

4.2 Putting the shield on

See also the user instructions for the SR

500 fan.

Check that the scale number of your lens

is correct for your work.

The shield is delivered with a welding

lens with scale No. 10.

Put the fan on your waist and adjust the

belt so that the fan is located firmly and

comfortably at the back of your waist.

Start the fan and adjust the air flow to

suit your work intensity.

Raise the front piece and put the welding

shield on.

If necessary, adjust the head harness in

height by lengthening or shortening the

strap for the top of the head.

The sweatband should be fitted just

above the eyebrows.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

5 of 22

If necessary, adjust the circumference of

the head harness by means of the rear

knob. The head harness should be fixed

tight around your head.

Lower the front piece by pulling the face

seal down under your chin.

Adjust the neck size of the face seal by

means of the elastic neck strap.

Insert a finger between your cheek/chin

and the face seal and run the finger long

the contact surface of the face seal all

the way round to check that it fits well

against the face.

Check carefully that no escaping air

comes out around the cheek and chin.

Check that the front piece is in the fully

down position, no air should be coming

out from the part above the forehead.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

6 of 22

Make sure that the breathing hose runs

along your back and that it is not twisted.

4.3 Taking the shield of

Leave the polluted area before taking off

the equipment.

- Take the welding shield off.

- Switch off the fan. Release the

belt and remove the fan.

- After use, clean and check the

equipment.

5.1 Maintenance schedule

The schedule specifies the minimum

maintenance routine requirements to

ensure that the equipment is always in

good working order.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

7 of 22

5.2 Cleaning

Remove the fan filter, battery and belt,

and remove the welding lens and

protective lens from the shield before

cleaning.

Sundström cleaning wipes SR 5226 that

clean and disinfect are recommend for

daily maintenance.

If more heavily soiled, the equipment can

be carefully blown clean with

compressed air.

However, make sure that dirt particles do

not end up in the air intake of the fan.

The equipment can then be cleaned with

a soft brush or sponge, moistened in a

solution of washing-up liquid or the like

in lukewarm water.

!! Wipe the plastic protective lens

carefully, since they are sensitive to

scratching.

!! Automatic welding lenses are very

sensitive to moisture. Use only a dry

polishing cloth.

!! N.B. Never clean with a solvent.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

8 of 22

5.3 Storage

After cleaning, store the equipment in a

dry and clean place at room

temperature.

Avoid direct sunlight or other sources of

heat.

The fan filters should best be stored in a

tight plastic bag.

The battery can be stored in the

Sundström charging station SR 506.

6.1 Changing the welding lenses

The welding lens should be marked with

the scale number and approval symbol.

Raise the welding lens flap.

Use your fingers to release the spring.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

9 of 22

Change the welding lens.

Fold the spring back.

6.2 Changing the inner protective lens

The inner protective lens is fitted in the

front piece behind the welding lens flap.

Drawn up by:

2009-02-03 / RK

OI06H-4018 SR 590

Revision:

Reviewed:

Page:

10 of 22

Raise the welding lens flap.

Press the protective lens out with your

fingers from the inside of the shield.

Fit the new protective lens from the

outside.

Never use an inner protective lens made

of glass - risk of injury

by glass splinters.

Andere Handbücher für SR 590

Inhaltsverzeichnis

Andere Sundstrom Schweißzubehör Handbücher

Sundstrom

Sundstrom SR 592 Technisches Handbuch

Sundstrom

Sundstrom SR 590 Bedienungsanleitung

Sundstrom

Sundstrom SR 590 Bedienungsanleitung

Sundstrom

Sundstrom SR 584 Bedienungsanleitung

Sundstrom

Sundstrom SR 591 Bedienungsanleitung

Sundstrom

Sundstrom SR 592 Bedienungsanleitung

Sundstrom

Sundstrom SR 591 Bedienungsanleitung

Sundstrom

Sundstrom SR 584 Bedienungsanleitung

Sundstrom

Sundstrom SR 592 Bedienungsanleitung

Sundstrom

Sundstrom SR 591 Bedienungsanleitung

Sundstrom

Sundstrom SR 591 Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Lincoln Electric

Lincoln Electric LT-7 Tractor Bedienungsanleitung

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung

LAHTI PRO

LAHTI PRO L1540400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric K3091-1 Bedienungsanleitung