Figure 4-2 Network topology of the NVR
When the NVR is started, the power indicator becomes steady
on and the NVR starts a self-test and displays the test result on
the screen. The startup process takes about 2 minutes.
When a hardware abnormality is detected, the self-test screen
stays on. You can click continue or shutdown in the lower right
corner of the screen. If you click continue, the NVR enters the
login screen.
Hard disk detection is performed during sta rtup. If the detection
fails, possible causes include：
The hard disk is new an d unformatted. In this case, forma t the
hard disk based on“ Quick Setup”.
The hard disk is formatted, but the file system is incons istent with
the one supported by the NVR.
The hard disk is damaged.
In some environments, if the power supply is abnormal ,
the NVR may not work properly. In severe cases, the NVR
may be damaged. In these environments, you are advise d
to use regulated po wer supply.
Figure 4-1 Login
Enter the correct user name and password. The main screen of
the NVR is displayed.
4.2 Adding Webcams
4.2.1 PoE
After the PoE network interfaces are connected to IP cameras,
the NVR automatically adds the IP cameras. Figure 4-2 shows the
network topology of the NV (e.g 2 Disks,4 PoEs).R
PoE
PoE
PoE
PoE
LAN Switch
Remote client
POE
1
24
3
HDMI
DC 12V
USB
VGA
RESET
LAN
LINE OU T
LINE IN
Figure 4-3 Topology of a free network
NVR
LAN2
switch LAN1
Remote Client IP camera
HDMI
DC 12V
USB
VGA
RESET
LAN
LINE OU T
LINE IN
LAN
The NVR is embedded with a web server and supports
mainstream browsers such as Internet Explorer, Chrome, Firefox,
and Safari. Operations such as quick setup, real-time preview,
video playback, alarm search, NVR setup, and camera setup can
be performed through the web.
Open the Internet Explorer, enter the IP address of IP camera
(default value: 192.168.0.121） in the address box, and press
Enter. The login page is displayed. as shown in figure 4-1 .
5.1 Quick Setup
Quick setup provide NVR network configuration, disk
management, time setting, IP camera search, video configuration,
camera network configuration, stream configuration, and mobile
detection configuration, as shown in figure 5-1.
5.1.1 NVR Setup
NVR basic information: You can set the device name and device
time of the NVR.
Sync Camera Time: It can be done manually or automatically.
If the manual mode is selected, click to synchronize the time
of IP cameras. If the auto mode is selected, the NVR
synchronizes the time of IP cameras automatically.
Authentication Accounts: To log in to an IP camera, you need to
enter the correct authentication account. Only successfully
authenticated IP cameras can be managed. Double-click the
user name and password text field to modify the user name and
password.
NVR network configuration: You can enable automatic IP
address acquisition and set the IP address, subnet mask,
default gateway, DNS address of the NVR, and display the
network connection status and speed.
Hard disk management: You can manage the hard disk of the
NVR as follows:Format the hard disk; Check the status of the
hard disk (usable, abnormal, unformatted, and unavailable);
Check the used space and total space of the hard disk.
Formatting will clear all video data on the hard disk.
Use this function only when necessary.
Be sure to uninstall the hard disk before removing it
from the NVR during runtime; otherwise, the hard disk
may be damaged or data may be lost.
The NVR must be connected to a stable power supply
during runtime; otherwise, the hard disk may be
damaged or data may b e lost.
5.1.2 Camera setup
Camera search and deletion
When you need to search camera for management, click
Search Camera, the Camera Search page is displayed, then click
Scan, it will scan for the camera automatically, as shown in figure
4-1. Click , the camera selecting page is displayed, Select the
cameras you want and click , then click Ok to complete
selection of IP cameras.
To remove managed cameras, check the cameras in the camera
list and click to delect cameras.
IP camera setup
You can view the status of an IP camera and set the name, IP
address, record policy, stream parameter, and motion alarm
parameter of the IP camera.
View the status of an IP camera: The camera status may be
Online, Offline, and Incorrect account. For an online IP
camera, click to view live video.
Chang the channel name: Click a selected channel name, enter
a channel name in the Name text field.
Set a record policy: Click a selected record, the Record Policy
Configuration page is displayed. For how to set a record policy,
see the Record of Network Video Recorder (NVR) User Guide.
Figure 5-1 Quick Setup
Set a stream: Click a selected stream, the Stream page is
displayed，Set stream parameters, select On for Apply to all the
same devices, and click OK. The parameter settings are applied
to all IP cameras that have the same resolution as the
configured resolution.
Set a motion alarm: Click the motion alarm information, the
Motion Alarm page is displayed. Set the schedule and motion
area when the motion detection alarm function is enabled.
Quick Configuration(e.g IE)
5
Quick Configuration(e.g IE)
4
Component
Hazardous Su bstance or Elemen t
Plumbum
(Pb)
Mercury
(Hg) Cadmium
(Cd)
Hexavalent
Chromium
(Cr6+)
Polybromin a-
ted Biphenyl s
(PBB)
Structural
part
Board/
circuit
module
Cable
connector
Accessor-
ies
○: indicates that the concentration of the hazardous s ubstance in
all homogeneous s ubstances of the component is within the
limit specified in SJ/T 11363-2006 Requirements for
Concentration Limits for Certain Hazardous Substances in
Electronic Information Products.
×: indicates that the concentration of the hazardous s ubstance in
at least one homogeneous substance of the component
exceeds the limit specified in SJ/T 11363-2006
Requirements for Concentration Limits for Certa in
Hazardous Substances in Electronic Information Products.
×
×
×
×
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Polybromin ated
Diphenyl Eth ers
(PBDE)
NOTE
Appendix：
Hazardous Substance Declaration
5
4.1 Startup
Before starting NVR, ensure that the NVR is connected to a
power supply properly and a monitor is connected to the HDMI or
VGA interface of the NVR correctly. NVR will automatically power-
on, When it is connected to a power supply,
CAUTI ON
NOTE
NOTE
The default user name is admin. The default password is admin.
Change the password when you log in the system for first time to ensure
system security.
You can change the system display language on the login page.
A free network includes other network devices in addition to IP
cameras and NVR. The topology of a free network can be
organized freely so long as NVR and IP cameras can
communicate with each other smoothly.
When a free network is used, the user needs to manually
search for and add IP cameras. For details, see chapter 5.1"Quick
Setup”.
4.2.2 Non-PoE
CAUTI ON
To browse a real-time video, click Live Video. The Live Video
page is displayed in figure 5-2., as shown
Figure 5-2 Live Video
Str eam Ca mera
Live Video Playback C onf igu ration
5.2 Live video
2
1
3
4
56
Mobile phone client
6
Mobile phone client supports
IOS、Android syetem，search
”Inview Pro” or “Inview Lite” in the
App store and install it.
Click icon ,the main menu is
displayed,as shown in figure 6-1.
You can perform the following
operation:
Live preview
Playback
Device Manage
Image
Figure 6-1 Main menu
Live Pre vie w
Playback
Devices
Images
Settin g Help
