Sunrise telecom SSxDSL-5M Bedienungsanleitung
1SSxDSL-5M
IDSL Module
for the MTT and xDSL
Family of Products
MAN-10980-US001 Rev. H00
302 Enzo Drive San Jose, CA 95138
Tel: 1-408-363-8000 Fax: 1-408-363-8313
User’s Manual
SSxDSL-5M
2 SSxDSL-5 IDSL Module
WARNING
Using the supplied equipment in a manner not specified by Sunrise Telecom may
impair the protection provided by the equipment.
CAUTIONS!
• Donotremoveorinsertthemodulewhilethetestsetison.Insertingorre-
movingamodulewiththepoweronmaydamagethemodule.
• Donotremoveorinsertthesoftwarecartridgewhilethetestsetison.Oth-
erwise,damagecouldoccurtothecartridge.
End of Life Recycling and Disposal Information
DO NOT dispose ofWaste Electrical and Electronic Equipment (WEEE) as
unsorted municipal waste. For proper disposal return the product to Sunrise
Telecom. Please contact our local offices or service centers for information on
howtoarrangethereturnandrecyclingofanyofourproducts.
EC Directive on Waste Electrical and Electronic Equipment (WEEE)
The Waste Electrical and Electronic Equipment Directive aims to
minimize the impact of the disposal of electrical and electronic
equipment on the environment. It encourages and sets criteria for
the collection, treatment, recycling, recovery, and disposal of waste
electrical and electronic equipment.
© 2010 Sunrise Telecom Incorporated. All rights reserved.
Disclaimer:Contentssubjecttochangewithoutnotice.
3SSxDSL-5M
IDSL Module
1 IDSL Module.......................................................5
1.1 Test Set LEDs ...................................................................5
1.2 Module Connector Panel ...................................................7
2 IDSL Menus ........................................................9
2.1 IDSL/ISDN BERT Main Menu..........................................10
2.1.1 Test Configuration.........................................................10
2.1.1.1 U Interface Test Configuration ...................................11
2.1.1.2 S/T Interface Configuration........................................14
2.1.2EOCControl ................................................................16
2.1.3 M4 Access....................................................................18
2.1.4 BERT and Results ........................................................20
2.2 40 kHz Tone.....................................................................23
2.3 ISDN-BRI.........................................................................24
2.3.1 Test Configuration.........................................................24
2.3.2 Call Setup.....................................................................27
2.3.3 D-Channel Status .........................................................29
2.3.4OtherFeatures .............................................................30
2.3.4.1 Auto SPID Detect ......................................................31
2.3.4.2 Guess SPID ..............................................................31
2.3.4.3 Auto Service Scan.....................................................32
2.3.4.4 Self BERT Call...........................................................33
2.3.4.5 Dual BERT Call .........................................................34
2.3.4.6 Bonding Call ..............................................................35
2.3.4.7 Supplementary Service Scan ....................................36
2.3.5 BERT and Results ........................................................38
2.3.6 Protocol Analysis..........................................................40
2.3.6.1 Filter Setup ................................................................40
2.3.6.2ViewPrintBuffer ........................................................41
2.3.7OtherSetup ..................................................................47
2.4 X.25-BRI..........................................................................49
2.4.1 Test Configuration.........................................................49
2.4.2 Call Setup.....................................................................51
2.4.3 Protocol Analysis..........................................................53
2.4.3.1 Filter Setup ..................................................................53
2.5 SRAM Utility ....................................................................61
2.6View/Store/Print...............................................................62
2.6.1 Saving a Test ................................................................63
2.6.2ViewingaStoredTest ...................................................63
2.6.3 Printing a Stored Test ...................................................63
2.6.4 Deleting a Stored Test ..................................................63
2.6.5 Locking & Unlocking a Stored Test ...............................63
2.6.6 Renaming a Stored Test ...............................................63
2.7 Profiles.............................................................................65
4 SSxDSL-5 IDSL Module
3 Applications.....................................................67
3.1 LT Mode Testing...............................................................67
3.2 ISDN Call Setup Testing ..................................................69
3.3 X.25-BRI Testing..............................................................70
4 General Information ........................................73
4.1 Testing and Calibration Statement...................................73
4.2ExpressLimitedWarranty................................................73
4.3 Customer Service............................................................73
Index ......................................................................75
5SSxDSL-5M
1 IDSL Module
1.1 Test Set LEDs
SSMTT-ACM, -ACM+, -EX SSMTT-B, -C
Figure 1 Test Set LED Panels
ThefollowingtestsetLEDsshowninFigure1areused.Noteif
anLEDisblinking,pressHISTORYtoclear.
MODULE
• Green:Testsetisinmodulemode.
SIGNAL
•
Green: The test set is receiving valid signal
at the proper inter-
face
.
For example, if the test set is configured for U interface
testing, this is green to indicate it is receiving a signal at the
U interface.
•
Red:
Itisredwhenthetestsetisnotreceivingasignal.
LP 1 SYNC
• Green:Layer1framesynchronizationisestablished.ForISDN
testingitblinksgreenwhenLayer1framesyncisestablished,
but the SPIDs have not yet been initialized. It is solid green
once the SPIDs have been accepted.
• Red:Noframesynchronizationhasbeenestablished.
FRAME
• Green:thetestsetisreceivingavalidsignalandhasacquired
frame synchronization on the external clock signal.
• Red:Thetestsetisnotdetectingtheexternalclocksignalat
the interface. See External Clock Signal.
ERRORS
• Red:Thetestsetiscurrentlydetectinganerror.ForS/TIn-
terface testing, this could be a Frame error. For U interface
testing, this could be NEBE or FEBE errors.
• BlinkingRed:Thetestsethaspreviouslydetectedanerror,
but that error is no longer present.
6 SSxDSL-5 IDSL Module
BPV/CODE
• Red:ThetestsetiscurrentlydetectingaBipolarViolationon
the S/T interface.
• BlinkingRed:ThetestsethaspreviouslydetectedaBPVon
the S/T interface, but the error is no longer present.
PAT SYNC
• Green:Thetestsethasachievedpatternsynchronizationdur-
ing IDSL BERT testing or during an ISDN data call.
• Red:Thetestsethaslostpatternsynchronizationorcannot
achieve pattern sync.
BIT ERR
• Red:Thetestsetiscurrentlydetectingbiterrors.
• BlinkingRed:Thetestsethaspreviouslydetectedbiterrors,
but they are no longer present.
7SSxDSL-5M
1.2 Module Connector Panel
ThemoduleconnectorpanelisshowninFigure2.
HANDSET U EXT CLK
T1/E1
EXT CLK ST U-281Q
Figure 2 Module Connector Panel
Themodulecontainsthefollowingports:
U-2B1Q
ThisisanRJ-45portwhichusesthecenterpins(4,5).Itshould
beusedwhentheUinterfacehasbeenselectedinTESTCON-
FIGURATIONandaretestingatthe2-wireUinterface.
S/T
ThisisanRJ-45portwhichusespins3,4,5,and6.Itshouldbe
used when the S/T interface has been selected S/T inTEST
CONFIGURATIONandaretestingatthe4-wireS/Tinterface.
T1/E1 EXT CLK
This bantam port should be used to retrieve timing from the T1 or
E1signal.UseitinLTmodewhenEXT-T1orEXT-E1hasbeen
selected as the TX Clock source. This reference signal can be
obtained from the output of the BITS clock or any T1/E1 signal
carryingthenetworkclockreference.
U EXT CLK
This port should be used to retrieve the timing from the U interface
2B1Qsignal.UseitinLTmodewhenEXT-Uhasbeenselectedas
the TX Clock source. A U 2B1Q reference signal can be obtained
from an IDSL output on a DSLAM.
HANDSET
This is an RJ-9 port that requires the Sunrise Telecom SS427
handset.
8 SSxDSL-5 IDSL Module
9SSxDSL-5M
2 IDSL Menus
Themenutreeshowsthelocationofmajormenuitems:
IDSL/ISDN BERT
2.1.1
TEST CONFIGURATION
EOC CONTROL
2.1.2
M4 ACCESS
2.1.3
BERT AND RESULTS
2.1.4
IDSL - BRI
2.3.1
TEST CONFIGURATION
CALL SETUP
2.3.2
D CHANNEL STATUS
2.3.3
OTHER FEATURES
2.3.4
BERT AND RESULTS
2.3.5
PROTOCOL ANALYSIS
2.3.6
OTHER SETUP
2.3.7
IDSL MAIN MENU
2.1
IDSL BERT
40 kHz TONE
2.2
ISDN - BRI
2.3
X.25 - BRI
2.4
SRAM UTILITY
2.5
VIEW/STORE/PRINT
2.6
PROFILES
2.7
MODULE
KEY
X.25 - BRI
2.4.1
TEST CONFIGURATION
CALL SETUP
2.4.2
PROTOCOL ANALYSIS
2.4.3
OTHER SETUP
2.4.4
Figure 3 Module Menu Tree
10 SSxDSL-5 IDSL Module
2.1 IDSL/ISDN BERT Main Menu
See Section 3.1 for procedures for LT Mode Testing.
This menu screen contains:
• TESTCONFIGURATION
• EOCCONTROL
• M4ACCESS
• BERTANDRESULTS
2.1.1 Test Configuration
The conguration settings change slightly whether a U or S/T
interface is tested.
INTERFACE
Options:U(F1),S/T(F2)
• U:Usewhenconnectingthemoduletothe2-wireUinterface.
Whenused,usetheU2B1Qjackonthemodule.
• S/T(F2)Usewhenconnectingthemoduletothe4-wireS/T
interface.Whenused,usetheS/Tjackonthemodule.
DSLAM
or
CO Switch
LT U-281Q
NT
TE
S/T
NT1
U-281Q LT
U NT-144K Mode
U LT-144K Mode
Figure 4 U NT and LT-144K Modes
Inhaltsverzeichnis
Andere Sunrise telecom Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
