Supermicro AOC-PG-i2+ Bedienungsanleitung
AOC-PG-i2+ Add-on Card
User’s Guide
Revison 1.0a
AOC-PG-i2+ Add-on Card User’s Guide
ii
The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The
vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no
commitment to update or to keep current the information in this manual, or to notify any person or
organization of the updates. Please Note: For the most up-to-date version of this manual, please see
our web site at www.supermicro.com.
Super Micro Computer, Inc. (“Super micro”) reserves the right to make changes to the product described
in this manual at any time and without notice. This product, including software, if any, and documentation
may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or
machine without prior written consent.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE
THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,
SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF
REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,
SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara
County in the State of California, USA. The State of California, County of Santa Clara shall be the
exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not
exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instruction manual, may cause harmful interference with radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference,
in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning
applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further
details.
Manual Revison 1.0a
Release Date: February 4, 2010
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy
any part of this document.
Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2010 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS
PRODUCT MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER
REPRODUCTIVE HARM.
iii
Table of Contents
Chapter 1 Safety Guidelines..........................................................1-1
1-1 ESD Safety Guidelines.....................................................................1-1
1-2 General Safety Guidelines...............................................................1-1
1-3 An Important Note to Users.............................................................1-1
Chapter 2 Card Components.........................................................2-1
2-1 Front Components ............................................................................2-1
2-2 Front Connectors, Jumpers and LEDs..........................................2-2
LAN Ports................................................................................................2-2
LAN Port LEDs........................................................................................2-2
2-3 Riser Card..........................................................................................2-3
2-4 System Installation............................................................................2-4
Chapter 3 Installing the Drivers...................................................3-1
3-1 Installing the Drivers in Microsoft Windows ..................................3-1
3-2 Intel PROSet for Windows Device Manager.................................3-1
Installing Intel PROSet for Windows Device Manager............................3-2
Tips for PROSet Users.........................................................................3-2
Removing Intel PROSet for Windows Device Manager..........................3-2
Receive Side Scaling..............................................................................3-2
RSS Configuration ...............................................................................3-2
Teaming................................................................................................3-2
3-3 Installing the Base Driver and Intel PROSet via the Command Line
3-3
Installation Methods................................................................................3-3
Base Driver Installation...........................................................................3-3
Command Line Options .......................................................................3-3
Intel PROSet for Windows Device Manager Installation.........................3-4
Using the DxSetup.exe Utility...............................................................3-5
Command Line Examples....................................................................3-6
msiexec.exe Command Line Options ..................................................3-6
Command Line Switches ........................................................................3-7
Silent Install/upgrade Command Line Syntax ......................................3-7
Silent Uninstall Command Line Syntax................................................3-7
Command Line Options Supported by PROSETDX.msi ........................3-8
Command Line Install Examples..........................................................3-8
AOC-PG-i2+ Add-on Card User’s Guide
iv
Command Line Uninstall Example.......................................................3-9
Command Line Reinstall/Repair ..........................................................3-9
Chapter 4 Linux Base Driver for the
PRO/1000 Family of Adapters.......................................................4-1
4-1 Overview.............................................................................................4-1
4-2 Identifying Your Adapter...................................................................4-1
4-3 Building and Installation...................................................................4-2
4-4 Command Line Parameters.............................................................4-3
Notes on InterruptThrottleRate ...............................................................4-6
Speed and Duplex Configuration............................................................4-7
4-5 Additional Configurations.................................................................4-9
Configuring the Driver on Different Distributions.....................................4-9
Viewing Link Messages........................................................................4-9
Jumbo Frames.....................................................................................4-9
Ethtool................................................................................................4-11
Enabling Wake on LAN* (WoL)..........................................................4-11
NAPI...................................................................................................4-11
v
Introduction
About this Manual
This manual is written for system integrators, PC technicians and knowledgeable PC
users who intend to integrate SuperMicro's AOC-PG-i2+ add-on card add-on card to
their system.
Product Features
The AOC-PG-i2+ add-on card offers the following features:
• Intel 82576 LAN chip
• PCI-e x8 interface
• Low-profile, half-length PCI-e x8 proprietary form factor card
• Two RJ-45 connectors
• Jumbo frames support up to 9.5-KB packets
• VMDq for virtualized environments
• Next generation VMDq with loopback funtionality
• Support Pre-boot Execution Environment (PXE)
• RoHS 6/6
• Intel PROSet Utility for Windows supported network teaming
• Low latency interrupts
• Direct Cache Access (DCA)
• iSCSI remote boot
• Height of end bracket 8.0 cm (3.15”)
• Dimensions: 9.6 cm (5.78”) x 6.2 cm (2.44”) length/width
• Supports Category-5 cable up to 100 meters
NOTE: The AOC-PG-i2+ add-on card requires the RSC-R1UU-E8PR riser card
for mounting in systems.
NOTE: The AOC-PG-i2+ add-on card is designed for certain Supermicro
motherboards and server systems. Please go to www.supermicro.com for the
latest list of supported platforms.
AOC-PG-i2+ Add-on Card User’s Guide
vi
Operating Systems Supported
The AOC-PG-i2+ add-on card supports the following Operating Systems (OS):
• Windows 2000/Windows XP/Windows 2003/Windows 2008/Windows Vista
•Linux
•VMWare
An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest revision
available at the time of publishing. The card you have received may or may not look
exactly the same as the graphics shown in this manual.
Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before
any warranty service will be rendered. You can obtain service by calling your vendor for
a Returned Merchandise Authorization (RMA) number. When returning to the
manufacturer, the RMA number should be prominently displayed on the outside of the
shipping carton, and mailed prepaid or hand-carried. Shipping and handling charges will
be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online at:
http://www.supermicro.com/support/rma/
Whenever possible, repack the add-on card in the original Supermicro box, using the
original packaging materials. If these are no longer available, be sure to pack the add-on
card in an anti-static bag and inside the box. Make sure that there is enough packaging
material surrounding the add-on card so that it does not become damaged during
shipping.
This warranty only covers normal consumer use and does not cover damages incurred
in shipping or from failure due to the alteration, misuse, abuse or improper maintenance
of products.
During the warranty period, contact your distributor first for any product problems.
vii
Contacting SuperMicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
‘s-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
9
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3991
Web Site: www.supermicro.com.tw
Technical Support:
Email: support@supermicro.com.tw
Tel: +886-2-8228-1366, ext. 132 or 139
AOC-PG-i2+ Add-on Card User’s Guide
viii
Notes
1-1
Chapter 1
Safety Guidelines
To avoid personal injury and property damage, carefully follow all the safety steps listed
below when accessing your system or handling the components.
1-1 ESD Safety Guidelines
Electric Static Discharge (ESD) can damage electronic components. To prevent damage
to your system, it is important to handle it very carefully. The following measures are
generally sufficient to protect your equipment from ESD.
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing a component from the antistatic
bag.
• Handle the add-on card by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the card and peripherals back into their antistatic bags when not in use.
1-2 General Safety Guidelines
• Always disconnect power cables before installing or removing any components from
the computer.
• Disconnect the power cable before installing or removing any cables from the
system.
• Make sure that the add-on card is securely and properly installed on the
motherboard to prevent damage to the system due to power shortage.
1-3 An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest PCB
Revision available at the time of publishing. The card you have received may or may not
look exactly the same as the graphics shown in this manual.
AOC-PG-i2+ Add-on Card User’s Manual
1-2
Notes
Inhaltsverzeichnis
Andere Supermicro Computerhardware Handbücher
Supermicro
Supermicro AOC-SLG3-4E4R Bedienungsanleitung
Supermicro
Supermicro SuperWorkstation SYS-551A-T Bedienungsanleitung
Supermicro
Supermicro M12SWA-TF Bedienungsanleitung
Supermicro
Supermicro AOC-STG-i4T Bedienungsanleitung
Supermicro
Supermicro X12SPW-TF Bedienungsanleitung
Supermicro
Supermicro AOC-S25G6-M2S Bedienungsanleitung
Supermicro
Supermicro BPN-SAS3-836EL Bedienungsanleitung
Supermicro
Supermicro SuperWorkstation SYS-531A-IL Bedienungsanleitung
Supermicro
Supermicro Super C9X299-PGF Bedienungsanleitung
Supermicro
Supermicro FatTwin F620P3-RTBN Bedienungsanleitung
Supermicro
Supermicro BPN-NVMe3-216N-S4 Bedienungsanleitung
Supermicro
Supermicro SuperServer SYS-E300-12D-4CN6P Bedienungsanleitung
Supermicro
Supermicro H13SSL-N Bedienungsanleitung
Supermicro
Supermicro Optane Persistent Memory 200 Series Bedienungsanleitung
Supermicro
Supermicro A2SD1-3750F Bedienungsanleitung
Supermicro
Supermicro SuperWorkstation 5038A-I Bedienungsanleitung
Supermicro
Supermicro AOC-SHG3-4M2P Bedienungsanleitung
Supermicro
Supermicro BPN-SAS2-826EL Series Bedienungsanleitung
Supermicro
Supermicro AOC-ATG-b2TM Bedienungsanleitung
Supermicro
Supermicro A3SEV-2C-LN4 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
