Supermicro 6027R-E1CR12N Bedienungsanleitung

SUPER STORAGE SYSTEM

6027R-E1CR12N

SUPER

USER’S MANUAL

1.0a

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the 6027R-E1CR12N. Installation

and maintainance should be performed by experienced technicians only.

The 6027R-E1CR12N is a high-end storage system based on the SC826BE1C-

R920LP 2U rackmountable chassis and the X9DRi-LN4F+ dual processor

serverboard.

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with the

system and describes the main features of the X9DRi-LN4F+ serverboard and the

SC826BE1C-R920LP chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 6027R-E1CR12N into a

rack and check out the server conguration prior to powering up the system. If your

server was ordered without processor and memory components, this chapter will

refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 4: Standardized Safety Warnings

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

6027R-E1CR12N.

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and docu-

mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.

Any use or reproduction of this product is not allowed, except as expressly permitted by the terms

of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the manufacturer’s instruction manual, may cause harmful interference

with radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-

ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to the

State of California to cause birth defects and other repro-

ductive harm.

Manual Revision 1.0a

Release Date: February 22, 2016

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

Notes

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRi-LN4F+ serverboard, includ-

ing the locations and functions of connections, headers and jumpers. Refer to this

chapter when adding or removing processors or main memory and when recong-

uring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC826BE1C-R920LP chassis.

You should follow the procedures given in this chapter when installing, removing or

reconguring SATA or peripheral drives and when replacing system power supply

units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Specications

Preface

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

Processors ...................................................................................................... 1-2

Memory ........................................................................................................... 1-2

SAS ................................................................................................................. 1-2

Serial ATA........................................................................................................ 1-2

PCI Expansion Slots ....................................................................................... 1-2

Rear I/O Ports................................................................................................. 1-3

1-3 Server Chassis Features ................................................................................ 1-3

System Power................................................................................................. 1-3

Hard Drive Subsystem .................................................................................... 1-3

Front Control Panel......................................................................................... 1-3

Cooling System............................................................................................... 1-3

1-4 Contacting Supermicro.................................................................................... 1-6

Chapter 2 Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup......................................................................................... 2-1

Choosing a Setup Location............................................................................. 2-1

2-4 Warnings and Precautions.............................................................................. 2-2

Rack Precautions............................................................................................ 2-2

Server Precautions.......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

2-5 Installing the System into a Rack ................................................................... 2-4

Separating the Sections of the Rack Rails..................................................... 2-4

Installing the Inner Rail Extension .................................................................. 2-4

Outer Rack Rails............................................................................................. 2-6

Chapter 3 System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons ..................................................................................... 3-1

Reset............................................................................................................... 3-1

Power .............................................................................................................. 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Power Fail ....................................................................................................... 3-2

Overheat/Fan Fail: .......................................................................................... 3-2

vii

NIC1 ................................................................................................................ 3-2

NIC2 ................................................................................................................ 3-2

HDD................................................................................................................. 3-3

Power .............................................................................................................. 3-3

3-4 Drive Carrier LEDs.......................................................................................... 3-3

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements....................................................... 4-1

Warning Denition ........................................................................................... 4-1

Installation Instructions.................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation..................................................................................... 4-8

Restricted Area................................................................................................ 4-9

Battery Handling............................................................................................ 4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes........................................ 4-14

Product Disposal........................................................................................... 4-15

Hot Swap Fan Warning................................................................................. 4-16

Power Cable and AC Adapter ...................................................................... 4-18

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions ..................................................................................................... 5-1

Unpacking ....................................................................................................... 5-2

5-2 Connecting Cables.......................................................................................... 5-2

Connecting Data Cables ................................................................................. 5-2

Connecting Power Cables .............................................................................. 5-2

Connecting the Control Panel......................................................................... 5-2

5-3 Rear I/O Ports................................................................................................. 5-3

5-4 Installing the Processor and Heatsink ............................................................ 5-4

Installing an LGA2011 Processor.................................................................... 5-4

Installing a Passive CPU Heatsink ................................................................. 5-7

Removing the Heatsink................................................................................... 5-8

5-5 Installing Memory............................................................................................ 5-9

Memory Support.............................................................................................. 5-9

DIMM Installation ............................................................................................ 5-9

5-6 Adding PCI Add-On Cards............................................................................ 5-14

5-7 Serverboard Details ...................................................................................... 5-15

Table of Contents

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

viii

X9DRi-LN4F+ Quick Reference.................................................................... 5-16

5-8 Connector Denitions ................................................................................... 5-18

5-9 Jumper Settings ............................................................................................ 5-25

5-10 Onboard Indicators........................................................................................ 5-29

5-11 SATA Ports .................................................................................................... 5-30

5-12 Installing Software......................................................................................... 5-31

SuperDoctor III.............................................................................................. 5-32

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices.................................................................................. 6-1

Precautions ..................................................................................................... 6-1

Unpacking ....................................................................................................... 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 Accessing the Inside of the Chassis............................................................... 6-2

6-4 System Fans ................................................................................................... 6-3

System Fan Failure......................................................................................... 6-3

Replacing System Fans .................................................................................. 6-4

6-5 Air Shroud ....................................................................................................... 6-5

6-6 Drive Bay Installation/Removal ....................................................................... 6-6

Accessing the Drive Bays ............................................................................... 6-6

SAS/SATA Drive Installation............................................................................ 6-6

Hard Drive Backplane ..................................................................................... 6-8

6-7 Power Supply.................................................................................................. 6-9

Power Supply Failure...................................................................................... 6-9

Removing/Replacing the Power Supply.......................................................... 6-9

6-8 Attaching a JBOD Expansion Chassis...........................................................6-11

Chapter 7 BIOS

7-1 Introduction...................................................................................................... 7-1

7-2 Main Setup...................................................................................................... 7-2

7-3 Advanced Setup Congurations...................................................................... 7-3

7-4 Event Logs .................................................................................................... 7-23

7-5 IPMI............................................................................................................... 7-26

7-6 Boot............................................................................................................... 7-28

7-7 Security......................................................................................................... 7-29

7-8 Save & Exit ................................................................................................... 7-30

Appendix A BIOS Error Beep Codes

Appendix B System Specications

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

Chapter 1

Introduction

1-1 Overview

The 6027R-E1CR12N is a high-end storage system comprised of two main subsys-

tems: the SC826BE1C-R920LP 2U/rack mount chassis and the X9DRi-LN4F+ dual

processor serverboard. Please refer to our web site for information on operating

systems that have been certied for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the 6027R-E1CR12N, as listed below:

• Two passive CPU heatsinks (SNK-P0048P)

• Three 8-cm system fans (FAN-0126L4)

• One air shroud (MCP-310-29001-0N)

• SATA Accessories

One SATA backplane (BPN-SAS3-826EL1)

Twelve drive carriers (MCP-220-00075-OB)

• Hardware RAID Controller ( AOC-S3108L-H8IR)

• JBOD Expansion Port (AOM-SAS3-8I8E-LP)

• One rackmount kit (MCP-290-00053-0N)

Note: For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety info: http://www.supermicro.com/about/policies/safety_informa-

tion.cfm

Chapter 1: Introduction

1-1

1-2 1-3

Chapter 1: Introduction

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

1-2 Serverboard Features

The 6027R-E1CR12N is built around the X9DRi-LN4F+, a dual processor

serverboard based on the Intel C600 chipset and designed to provide maximum

performance. Below are the main features of the X9DRi-LN4F+. (See Figure 1-1

for a block diagram of the chipset).

Processors

The X9DRi-LN4F+ supports single or dual Intel® Xeon E5-2600 Series processors.

Please refer to the serverboard description pages on our web site for a complete

listing of supported processors (www.supermicro.com).

Memory

The X9DRi-LN4F+ has 24 DIMM slots that can support up to 1.5 TB of LRDIMM

(Load Reduced DIMM), 768 GB of RDIMM (Registered DIMMs) or 128 GB of

UDIMM (Unbuffered DIMMs) ECC/Non-ECC DDR3-1866/1600/1333/1066/800

SDRAM. See Chapter 5 for details.

SAS

An LSI 3108 controller card is included in the system to support 240 SAS3/SATA3

hard drives. (RAID 0, 1, 5, 6, 10, 50 and 60 supported). The SAS/SATA drives are

hot-swappable units.

Serial ATA

A SATA controller is also integrated into the chipset to provide two SATA 3 (6/Gbps)

and four SATA 2 (3 Gbps) ports, which are RAID 0, 1, 5 and 10 supported. The

SATA drives are hot-swappable units. RAID 5 supported with Windows OS only).

Note: The operating system you use must have RAID support to enable the hot-

swap capability and RAID function of the SATA drives.

PCI Expansion Slots

The X9DRi-LN4F+ has four PCI-E 3.0 x16 slots, one PCI-E 3.0 x8 slot and one

PCI-E 3.0 x4 (in a x8) slot. The default conguration includes an add-on card (AOC)

populating Slot #1 (PCI-E 3.0 x 16 slot) and a port plate with a JBOD expansion

port occupying slot #2 (PCI-E 3.0 x4).

Rear I/O Ports

The color-coded I/O ports include one COM port, a VGA port, four USB 2.0 ports

(additional USB headers are included on the serverboard), four gigabit Ethernet

ports and two external MiniSAS JBOD expansion port. A dedicated IPMI LAN port

is also included.

1-3 Server Chassis Features

The SC826BE1C-R920LP is an 2U form factor chassis designed to be used in a

storage conguration. The following is a general outline of the main features of the

SC826BE1C-R920LP chassis.

System Power

The SC826BE1C-R920LP features a redundant, hot-plug 920W power supply com-

posed of two separate power modules. This power redundancy feature allows you

to replace a failed power supply without shutting down the system.

Hard Drive Subsystem

The SC826BE1C-R920LP chassis was designed to support 12 hot-swap SATA

hard drives. An optional, internal xed drive mounting bracket (MCP-220-82611-

0N) may be added to support two 2.5" SATA drives.

Front Control Panel

The control panel on the SC826BE1C-R920LP provides you with system monitor-

ing and control. LEDs indicate system power, HDD activity, network activity, system

overheat and power supply failure. A main power button and a system reset button

are also included.

Cooling System

The SC826BE1C-R920LP chassis includes three 8-cm hot-plug system cooling fans

located in the middle section of the chassis. An air shroud channels the airow from

the system fans to efciently cool the processor area of the system. Each power

supply module also includes a cooling fan.

1-4 1-5

Chapter 1: Introduction

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

Figure 1-1. Intel C600 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details. Figure 1-2. X9DRi-LN4F+ Serverboard

PROCESSOR

QPI

DDR3 DIMM

SSB

Intel C606/C602

PEG0

DMI

PEG1 [4:1] USB

LPC

LAN

RJ45 RJ45

SATA

SYSTEM

BIOS

CPU REAR

CPU FRONT

PEG1_8

PCI-E x16 Slot

USB

REAR

HDR 2X5

0,1

TPM HDR

TYPE-A

REAR

2,3

QPI

DDR3 DIMM

Socket 1

Socket 2

PE3 PE2 PE1 DMI

DMI

PCI-E x8 Slot

PCI-E x16 Slot

x16

HDR 2X5

BMC VGA

VGA CONN

DDR III

PHY1

LAN

RTL8211

SPI

RJ45 RJ45

PCI-E x16 Slot

x16

x4 [7.4]

[3.0]

SIO

W83527

4,5 6, 7

PE3 PE2 PE1

SATA

SCU

#1~#6

#1~#8

(For X9DR3

-LN4F+ Only)

(4 SATA2 for X9DRi

-LN4F+ Only)

JRK1

JF1

JPI2C1

JPW3 JPW2 JPW1

JSD1

SP1

J18

J17

JBAT1

JP6

JP7

JI2C2

JI2C1

JL1

JOH1

FANB

FANA

FAN4

FAN3

FAN2

FAN6

FAN1

SW1

JPP1

JPP0

J21

JBT1

LEM1

JWP1

JPG1

JWD1

JPL1

JPME2

JPME1

USB4/5

JTPM1

XDP-PCH

(in X8 Slot)

CPU2 Slot6 PCI-E 3.0x8

CPU2 Slot5 PCI-E 3.0 x16

CPU2 Slot4 PCI-E 3.0 x16

CPU1 Slot3 PCI-E 3.0 x16

CPU1 Slot2 PCI-E 3.0 x4

BIOS BOX

CPU1 Slot1 PCI-E 3.0 x16

SAS0~3

SAS4~7

I-SATA0

I-SATA1

P2 DIMMF3

P2 DIMMF1

P2 DIMMF2

P2 DIMME3

P2 DIMME2

P2 DIMME1

P2 DIMMG1

P2 DIMMH1

P2 DIMMG3

P2 DIMMG2

P2 DIMMH2

P2 DIMMH3

COM1

USB6/7

UID

IPMI_LAN

Alaways populate DIMMx1 first

P1 DIMMA2

P1 DIMMA1

P1 DIMMB3

P1 DIMMB2

P1 DIMMB1

P1 DIMMA3

P1 DIMMC1

P1 DIMMC2

P1 DIMMC3

P1 DIMMD1

P1 DIMMD2

P1 DIMMD3

CPU2

I-SATA5

I-SATA4

I-SATA3

I-SATA2

LAN2/4

VGA

XDP-CPU

CPU1

COM2

BMC

CTRL

LAN1/3 USB 0/1

KB/Mouse

JBR1

PHY

FAN5

BIOS

LAN

CTRL

PCH

LE1

X9DR6-LN4F+/X9DRi-LN4F+

Rev. 1.10

Alaways populate DIMMx1 first

USB9

SAS

CTRL

USB 2/3

JSTBY1

IPMB

JD1

JF2

LE2

JPB1

JBMC1

JBOD ExpansionPort/Cable

AOC-SAS2LP-H8iR

Note: The SSG-6027R-E1CR12N comes pre-installed with a Hardware RAID

controller installed in PCI-E slot 1 and a JBOD expansion port installed in PCI-E

slot 2. Serverboard SAS components shown in the gure above are not included

on the X9DRi-LN4F+

1-6

SUPERSTORAGESYSTEM 6027R-E1CR12N User's Manual

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: [email protected]

Website: www.supermicro.com.tw

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your 6027R-E1CR12N up and

running. Following these steps in the order given should enable you to have the

system operational within a minimum amount of time. This quick setup assumes

that your system has come to you with the processors and memory preinstalled. If

your system is not already fully integrated with a serverboard, processors, system

memory etc., please turn to the chapter or section noted in each step for details on

installing specic components.

2-2 Unpacking the System

You should inspect the box the 6027R-E1CR12N was shipped in and note if it was

damaged in any way. If the server itself shows damage you should le a damage

claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the 6027R-E1CR12N.

It should be situated in a clean, dust-free area that is well ventilated. Avoid areas

where heat, electrical noise and electromagnetic elds are generated. You will also

need it placed near a grounded power outlet. Read the Rack and Server Precau-

tions in the next section.

2-3 Preparing for Setup

The box the 6027R-E1CR12N was shipped in should include two sets of rail as-

semblies, two rail mounting brackets and the mounting screws you will need to

install the system into the rack. Follow the steps in the order given to complete the

installation process in a minimum amount of time. Please read this section in its en-

tirety before you begin the installation procedure outlined in the sections that follow.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back

of the rack to allow for sufcient airow and ease in servicing.

Inhaltsverzeichnis

Andere Supermicro Lagerung Handbücher

Supermicro

Supermicro SuperServer SYS-211E-FRN2T Bedienungsanleitung

Supermicro

Supermicro SuperStorage SSG-136R-NR32JBF Bedienungsanleitung

Supermicro

Supermicro 2028R-E1CR24H Bedienungsanleitung

Supermicro

Supermicro 6028R-E1CR12N Bedienungsanleitung

Supermicro

Supermicro 6048R-E1CR24L Bedienungsanleitung

Supermicro

Supermicro Supero SC847DE16-R2K02JBOD Bedienungsanleitung

Supermicro

Supermicro 6048R-E1CR36N Bedienungsanleitung

Supermicro

Supermicro SUPER 6047R-E1CR36N Bedienungsanleitung

Supermicro

Supermicro SuperStorageSystem 6038R-E1CR16L Bedienungsanleitung

Supermicro

Supermicro Supero SC847DE16-R1K28LPB Bedienungsanleitung

Supermicro

Supermicro SuperServer SSG-620P-E1CR24H Bedienungsanleitung

Supermicro

Supermicro 6048R-E1CR24N Bedienungsanleitung

Supermicro

Supermicro SuperStorage 6028R-E1CR12H Bedienungsanleitung

Supermicro

Supermicro SuperServer 210P-FRDN6T Bedienungsanleitung

Supermicro

Supermicro SuperStorageSystem SSG-2028R-DN2R48L Bedienungsanleitung

Supermicro

Supermicro SuperServer SSG-640SP-E1CR60 Bedienungsanleitung

Supermicro

Supermicro SuperServer SSG-121E-NE316R Bedienungsanleitung

Supermicro

Supermicro SuperServer 110C-FHN4T Bedienungsanleitung

Supermicro

Supermicro 6028R-E1CR12T Bedienungsanleitung

Supermicro

Supermicro 2028R-ACR24L Bedienungsanleitung

Supermicro

Supermicro SSG-2028R-DN2R20L Bedienungsanleitung

Supermicro

Supermicro SuperServer SSG-540P-E1CTR45L Bedienungsanleitung

Supermicro

Supermicro 6048R-E1CR24H Bedienungsanleitung

Supermicro

Supermicro 6048R-E1CR60N Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung