Supero SC742 Bedienungsanleitung
1.0a
SC742 CHASSIS
USER'S GUIDE
742S
742i
1-2
SC742 Chassis User’s Guide
The information in this User’s Guide has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates. Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.
Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.
Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.
Copyright © 2005 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
1-3
Chapter 1: Safety Information and Technical Specifications
Table of Contents
Chapter I: Safety Information and Technical Specifications.......... 1-4
1-1. Safety Information............................................................................. 1-4
1-2. Technical Specifications.................................................................. 1-6
A. 742 SATA Back Panel................................................................. 1-6
B. SCA742-E2 SCSI Dual Channel Back Panel (w/GEM318)................... 1-8
C. SCA 742 SCSI Single Channel Back Panel (w/GEM359) .................. 1-10
D. SCSI (Super) GEM Driver Installation (*for the Windows OS) ....... 1-12
Chapter 2: Installation Instructions ..................................................... 2-1
1-4
SC742 Chassis User’s Guide
1-1 Safety Information
Electric Static Discharge (ESD) can damage electronic com-
ponents. To prevent damage to your system board, it is
important to handle it very carefully. The following measures
are generally sufficient to protect your equipment from ESD.\
Static-Sensitive Devices
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing the board from the anti-
static bag.
• Handle the board by its edges only; do not touch its components, periph-
eral chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the motherboard and peripherals back into their antistatic bags when
not in use.
• For grounding purposes, make sure your computer chassis provides ex-
cellent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.
• Use only the correct type of onboard CMOS battery as specified by the
manufacturer. Do not install the onboard battery upside down to avoid
possible explosion.
!
Chapter 1-Safety Information and Technical
Specifications
1-5
Chapter 1: Safety Information and Technical Specifications
To avoid personal injury and property damage, please carefully
follow all the safety steps listed below:
Before accessing the chassis:
1. Turn off all peripheral devices connected to the SC742.
2. Press the power button to power off the system.
3. Unplug all power cords from the system or the wall outlets.
4. Disconnect all the cables and label the cables for easy identification.
5. Use a grounded wrist strap designed to prevent static discharge when
handling components.
Removing the chassis covers:
After completing the above steps, you can remove the covers and install
components/peripheral devices into the chassis as described in Chapter 2.
1. Unlock and remove the screws and fasteners to remove the cover or
components.
2. Save all the screws and fasteners for later use. (If necessary, label these
screws or fasteners for easy identification.)
3. Follow the instruction given in Chapter 2 to remove the chassis covers.
Reinstalling the chassis covers:
To maintain proper system cooling and airflow, do not operate the system
without installing all chassis covers back to the chassis. To reinstall the chassis
covers, please follow the steps listed below:
1. Make sure that all components and devices are securely fastened
on the chassis and there are no loose parts/screws inside the chassis.
2. Make sure that all cables are properly connected to the connectors and ports.
3. Use the original screws or fasteners to install the covers to the chassis.
4. Be sure to lock to the chassis or the system to prevent unauthorized access.
5. For proper cooling, enclose the chassis with covers before operating the
system.
An important note to the user
All images and graphics shown in this manual were based upon the latest
chassis Revision available at the time of publishing. The chassis you’ve
received may or may not look exactly the same as the ones shown in this
manual.
STOP
1-6
SC742 Chassis User’s Guide
742 SATA
1-2 Technical Specifications
A. 742 SATA Back Panel
A-1 Connector/Jumper Locations
Front View
A-2 Connectors
D3: Overheat LED Indicator
J5: SATA #0 J6: SATA#1
J7: SATA #2 J8: SATA#3
J10: SATA #4 J12: SATA#5
J14: SATA #6
SATA#0 Act In
SATA#5 Act In
1
x
SATA#1 Act In
2
SATA#4 Act In
910
SATA#6 Act In SATA#2 Act In
SATA#3 Act In
x
Act In (JP26) Pin Definitions
x
JP10/JP13: 4-Pin PWR Connectors JP26: ACT In
199.70MM
135.00MM
JP25
11
JP18
D3
J5
J6
J7
J8
J10
J12J14
JP26
JP13JP10
4-Pin
PWR 4-Pin
PWR
+12V
1
Ground
4
Ground
+5V
4-Pin PWR Connector
s
Pin Definitions
2
3
1-7
Chapter 1: Safety Information and Technical Specifications
Buzzer Reset (JP18)
Open Disabled
Closed Enabled (*Default)
Overheat Temperature (JP25)
Pins Definition
Open 45
0
C
1-2 50
0
C
2-3 55
0
C
A-3 Jumpers
JP18: Buzzer Reset
Rear View (*Not drawn to scale)
A-4Connector/LEDIndicatorLocations(RearSide)
A-5ActivityLEDIndicators
D22
D21
D18
D15
D14
D13
D12
J1 J2 J3 J4 J9 J11 J13
SATA0
SATA1
SATA2
SATA3
SATA4
SATA5
SATA6
JP25: Overheat LED
Activity LED Indicators
LED# Drive#
D12 SATA#0: Active
D13 SATA#1: Active
D14 SATA#2: Active
D15 SATA#3: Active
D18 SATA#4: Active
D21 SATA#5: Active
D22 SATA#6: Active
1-8
SC742 Chassis User’s Guide
B. SCA 74-E2 SCSI Dual Channel Back Panel (W/GEM318)
Front View (*Not Drawn to Scale)
B-1 Connector/Jumper Locations
B-2 Connectors
JP10/JP15: 4-Pin PWR Connectors
+12V
1
Ground
4
Ground
+5V
4-Pin PWR Connector
s
Pin Definitions
2
3
B-3 Jumpers
JP18: Buzzer Reset
742 SCA E2
JP23
JP20
JP14
JP22
JP18
SCSI Chan. A
SCSIChan.B
JP15
JP10
Channel A Jumpers
Jumpers Definition
JP14 Ch.A Delay Start
JP22 Ch.A Remote Start
Channel B Jumpers
Jumpers Definition
JP20 Ch.B Delay Start
JP23 Ch.B Remote Start
SCSI Channel A Jumpers SCSI Channel B Jumpers
Buzzer Reset (JP18)
Open Disabled
Closed Enabled (*Default)
1-9
Chapter 1: Safety Information and Technical Specifications
B-4Connector/LEDIndicatorLocations(Rear)
Rear View (*Not drawn to scale)
D24
D25
D23
D20
D22
D15
D17
D14
D13
D16
D6
D12
D5
SCA1 SCA2 SCA3 SCA4 SCA5 SCA6 SCA7
Ch. A-ID#0
Ch. A-ID#1
Ch. A-ID#2
Ch.B-ID#0
Ch.B-ID#1
Ch.B-ID#2
Ch.B-ID#3
D21
B-5 LED Indicators (Rear)
Drive Fail LED Indicators
LED# Drive ID# SCA#
D5 Channel A-ID#0 SCA 1: Fail
D6 Channel A-ID#1 SCA 2: Fail
D16 Channel A-ID#2 SCA 3: Fail
D17 Channel B-ID#0 SCA 4: Fail
D22 Channel B-ID#1 SCA 5: Fail
D23 Channel B-ID#2 SCA 6: Fail
D25 Channel B-ID#3 SCA 7: Fail
Drive Activity LED Indicators
LED# Drive ID# SCA#
D12 Channel A-ID#0 SCA 1: Active
D13 Channel A-ID#1 SCA 2: Active
D14 Channel A-ID#2 SCA 3: Active
D15 Channel B-ID#0 SCA 4: Active
D20 Channel B-ID#1 SCA 5: Active
D21 Channel B-ID#2 SCA 6: Active
D24 Channel B-ID#3 SCA 7: Active
SCSI Drive Fail LED Indicators
SCSI Drive Activity LED Indicators
1-10
SC742 Chassis User’s Guide
+
+
U6
C. SCA 742 SCSI Single Channel Back Panel (w/GEM359)
Front View (*Not Drawn to Scale)
C-1 Connector/Jumper Locations
C-2 Connectors
JP10/JP26: 4-Pin PWR Connectors
+12V
1
Ground
4
Ground
+5V
4-Pin PWR Connector
s
Pin Definitions
2
3
C-3 Jumpers
JP19: Buzzer Reset
SCSI
JP26
JP10 JP19
Buzzer Reset (JP19)
Open Disabled
Closed Enabled (*Default)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Supero Chassis Handbücher
Supero
Supero Supero SC825 Series Bedienungsanleitung
Supero
Supero CSE-101 Bedienungsanleitung
Supero
Supero SC512C Series Bedienungsanleitung
Supero
Supero Supero SC825 Series Bedienungsanleitung
Supero
Supero SC113 Series Bedienungsanleitung
Supero
Supero SC835 Chassis Series Bedienungsanleitung
Supero
Supero SC510T-200B Bedienungsanleitung
Supero
Supero SC510-200B Bedienungsanleitung
Supero
Supero SC111 Series Bedienungsanleitung
Supero
Supero SC811 Series Bedienungsanleitung
Supero
Supero SC812 Series Bedienungsanleitung
Supero
Supero SC812L Series Bedienungsanleitung
Supero
Supero SC742i Bedienungsanleitung
Supero
Supero SC847A-R1400LPB Bedienungsanleitung
Supero
Supero SC836A-R1200B SC836E1-R800BSC836E1-R800V Bedienungsanleitung
Supero
Supero SC847J SAS2 Series Bedienungsanleitung
Supero
Supero SC513-L260 Series Bedienungsanleitung
Supero
Supero SC828 Series Bedienungsanleitung
Supero
Supero SC847J Series Bedienungsanleitung
Supero
Supero Supero SC743 Bedienungsanleitung
