0 0 0 0
0 0 0 0
The SuperTooth® Melody is a Bluetooth® A2DP stereo headset.
You can listen to music from a compatible phone, tablet,
computer, laptop or music player. You can also make and
answer calls hands-free with your compatible mobile phone.
You can use the headset with compatible devices that support
Bluetooth® A2DP wireless technology.
To use the headset, place it over your head with the pad
indicated with L on the left ear and the pad with R on the right
ear.
Adjust the headband length so that the speaker pads rest
comfortably.
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipmentgenerates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause undesired
operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specic operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
For the whole declaration please visit : http://www.supertooth.net/download
Euro Communication Equipements SAS
Route de Foix D117
11500 NEBIAS (FRANCE)
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection
systems). This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government oce, for details of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal. This
product has an embedded, non-replaceable battery, do not attempt to open the product or
remove the battery as this may cause injury and damage the product. Please contact the local
recycling facility for removal of the battery. The embedded, non-replaceable battery is designed
to last the life time of the product.
Hereby, EURO COMM UNICATI ON EQUIPEM ENTS, represented by Xavie r Marchant, CEO,
declares that the SuperTooth® Melody, MODEL BT-300, is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal
equipment and the mutual recognition of their conformity.
Reconnectthe headset
To connect the headset to the device that you have last used with it, switch on
the headset and it will reconnect automatically. If it doesn’t, enable connection
in the Bluetooth menu of your device.
Adjust the volume
To adjust the headset volume, press the volume up (5) or down (4) button
during a call or while listening to music. To adjust the volume quickly, press and
hold either button.
Warning:
Excessive sound pressure from earphones and headphones can cause hearing
loss.
Calls
To make a call, dial the phone number on your phone keypad.
Toredialthenumberyoulastcalled(ifyour phonesupportsthisfeaturewiththe
headset), when no call is in progress, short press the multifunction (7) button.
To activate voice dialling (if your phone supports this feature with the headset),
whenno callisin progress,pressthemultifunction(7)button twicequickly until
the phone starts voice dialling, and process as described in the phone user
guide.
To answer or end a call, short press the multifunction (7) button or use the
phone buttons.
To reject a call, press and hold the multifunction (7) button for about 2 seconds.
To mute or unmute the microphone during a call, press the play / pause (8)
button.
To switch a call from the headset to the connected phone, press and hold the
multifunction (7) button for about 2 seconds.
To switch the call from the phone to the headset, press and hold the
multifunction (7) button for about 2 seconds.
Listen to music
To listen to music, connect the headset to compatible music player that
supports the A2DP Bluetooth prole.
The available music functions depend on your music player.
If you receive or make a call while listening to music, the music is paused until
you end the call.
To play a track, select it in the music player, and press the play / pause (8)
button.
To pause or resume playing, press the play / pause (8) button.
To stop playing, press the play / pause (8) button twice quickly.
To select the next track during playing, press the forward (9) button once.
To select the previous track, press the rewind (6) button once.
To scroll through the current track quickly, press andhold eitherb utton.
Clear settingsor reset
To clear the pairing settings from the headset, switch o the headset, and press
and hold the multifunction (7) button and the volume down (4) button (for
over 8 seconds) until the Bluetooth indicator ashes red, green and blue three
times.
To hardware reset the headset, connect the headset to a charger or plug it on a
computer, and press both the multifunction (7) button and the volume up (5)
button.
Charge the battery
When the battery is discharged, the headset beeps about every minute, and
the Bluetooth indicator (10) ashes red.
To charge the headset:
1. Connect the USB cable to your computer or to a USB charger.
2. Connect the USB cable to the charger connector (2).
The charge indicator (1) ashes steady red while charging.
3. When the battery is fully charged, the charge indicator (1) ashes
steady green. Disconnect the cable from the headset.
The fully charged battery has power for up to 7 hours and 30 minutes of talk
time, up to 90 hours of standby time, or up to 7 hours and 30 minutes of
music playing time.
Warning:
1. Attention should be drawn to the environment aspects of battery
disposal.
2. Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine or re.
Switch on
To switch on, press and hold the multifunction (7) button about 4 seconds.
The headset beeps, and the Bluetooth indicator (10) ashes green.
When the headset tries to connect to the last used phone or music player,
the Bluetooth indicator (10) blinks green slowly. When the headset is
connected to a device and is ready to use, the Bluetooth indicator (10) blinks
blue slowly. If the headset has not been paired with a device, it automatically
enters in pairing mode.
Switch o
To switch o, press and hold the multifunction (7) button for about 4
seconds. The headset beeps, and the Bluetooth indicator (10) ashes red.
If the headset is not connected to a device within 10 minutes, it switches o
automatically.
Pairing
1. Please make sure that your phone or music player is switched on.
2. To pair the headset if it has not been previously paired with a device,
switch on the headset. The headset enters in pairing mode, and the
Bluetooth indicator (10) blinks blue quickly.
To pair the headset if it has been previously paired with another device,
make sure that the headset is switched o, and press and hold the
multifunction (7) button (for about 6 seconds) until the Bluetooth
indicator (10) blinks blue quickly.
3. Activate the Bluetooth feature on your phone or music player, and set
it to search for Bluetooth devices.
4. Select "STMELODY" from the list of found devices on your phone or
music player.
5. If necessary, enter the passcode 0000 to pair and connect the headset
to your device.
6. The Bluetooth indicator (10) blinks blue slowly. The headset is ready to
use.
Disconnect the headset
To disconnect the headset from your device, switch o the headset, or
disconnect it in the Bluetooth menu of your device.
0700
The Bluetooth® word mark and logos are registered trademarks owned by BluetoothSIG, I nc.and any use of such
marks by Euro-CB is under license. Other trademarks and trade names are those of their respective owners.
FoldingCutting
