Sutron XLink 100/500 Bedienungsanleitung

XLINK100/500

Quick Start Guide

Schnellstart-Anleitung

Guía de inicio rápido

Guide de démarrage rapide

Part No. 8800-1218 Rev C

November 21, 2018

Table of Contents

English …………………………………………………………………………………..……EN-1

Deutsch………………………………………………………………………………..……..DE-1

Español………………………………………………………………………………..………ES-1

Français ……………………………………………………………………………….……..FR-1

XLINK100/500 Quick Start Guide

Android and Google Play are registered trademarks of Google LLC

Apple, App Store and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.

EN-1 8800-1218 Rev C.

Search terms: Sutron Linkcomm

2. Physical Connection to XLink 100/500

Connecting power:

1. Connect a battery or power source (9 –20 VDC)

across terminals 1 and 2

2. If connecting a solar panel, connect between

terminals 3 and 4 on XLINK500

Connecting to PC:

3. USB - Connect a micro USB cable between PC

and “USB Device” port on XLINK 100/500

4. Wi-Fi –Press the Wi-Fi button on the unit to turn

on XLINK 100/500 hotspot; On the PC, select the

Wi-Fi network from Network Connections.

This quick start guide will show steps on how to

•Install LinkComm software

•Connect XLINK100/500 to a PC

•Connect a Lufft WS400-UMB sensor to XLINK 100/500

•Setup measurement intervals and transmission content

•Setup transmissions to HydrometCloud every 1 hour in MIS format

•Setup alarms to send a message when the temperature goes above 300C and after it falls

below 280C

1. Install LinkCOMM Software

Android™: App is available on

Google Play™

Apple®: download from

Apple App Store®

PC or Mac OS X®: download from

www.sutron.com/product/linkcomm/

Note: For Windows 7, install the

driver from LinkComm menu.

Newer versions of Windows do not

require the driver.

Battery cable shall have an inline fast fuse

to handle current up to 5A

EN-2 8800-1218 Rev C.

3. LinkComm Session with XLink 100/500 via USB

Run LinkComm application, and do the following for USB interface:

Select “New Station”

Select “Station type” as per the unit model

Set “Connect type” to USB; “Device” shall automatically show MAC ID of XLINK 100/500

Press “Connect” to interact with the unit

4. LinkComm session with XLINK 100/500 via Wi-Fi

Follow steps 3.1 and 3.2

Set “Connect type” to “Station Wi-Fi”;

Press “Connect” to interact with the unit ; If error “Please

connect to Station Wi-Fi” appears, check the PC Wi-FI

connection

3.1

3.2

3.3

3.4

EN-3 8800-1218 Rev C.

5. Connect and configure the sensor

Go to the “Measurements” tab in LinkComm

Select “Active” to activate measurement “M1” and press “Sensor Template” for pre-defined

sensor setups.

Filter “Lufft” as a manufacturer and “SDI-12” as interface , and select “WS400-UMB” as a

model; Press “Yes” in the next prompt

“Configuration” can be left unchanged

Set Schedule with time as “00:00:00”,

Averaging time “00:00:00” and Interval

as “00:15:00”

6. Setup Alarms, logging interval and a transmission content

Continue in “Measurements” tab in LinkComm

Setup Alarm type “High” with a threshold of 30,

Alarm tx mode as “Tx In and Out” and a

deadband of 2.

Select “Log All” to log all measurements into

memory

Telemetry1’s “Tx data content1” can be left at

“All Logged” to send data measured and logged

after the last transmission.

Alarms are used to send immediate notifications when

sensor readings read a certain threshold; More details can

be found in XLINK 100/500 operating manual

5.1

5.2

5.3

5.5

5.4

6.2

6.3

6.4

EN-4 8800-1218 Rev C.

7. Select the data format and destination server

Go to the “Telemetry” tab in

LinkComm

Select “Enable” to turn on TX1, and

select radio type as “Cell,” kind as

“scheduled” and the label is optional

Set scheduled time and interval as

“00:00:30” and “01:00:00”

respectively

Select Tx format as “MIS” and date

format as “YYYYMMDD”

Setup “scheduled” transmissions as

shown on the right

Setup “Alarm” transmissions

The setup is now ready to be sent to

XLINK100/500; Click the “Changed”

icon and transfer the setup;

8. Send Setup to the unit and start recording

Following step # 7.7, recording can be turned on the unit, by toggling the “Stop” symbol

This completes the setup of the unit.

9. Get More Information

Download the user manual from http://www.sutron.com/downloads.htm

Watch YouTube Videos on Sutron Channel

Contact Sutron customer service –[email protected]

7.1

7.2

7.3

7.4

7.5

7.7

7.6

EN-5 8800-1218 Rev C.

SIM Card Installation and Removal Instructions

Following section details the instructions involved in installation and removal of SIM cards for Sutron Cell

modems

1. Sutron Cell modems support only “micro SIM” size.

2. Care must be exercised while handling the sim card and modem.

2.1. Sim card should be handled using clean hands to avoid any dirt or smudges being left on the SIM

card.

2.2. The modem should be handled in a clean environment to prevent any dirt accumulation or ESD

damage.

3. To install the SIM card,

3.1. Remove the modem card from carrier board carefully. If the modem is installed in XLINK 100/500,

remove power to XLINK 100/500, and carefully pull the cellular board out.

3.2. Flip the modem board carefully, without much stress on the U.FL cable; Insert the micro-sized sim

card, and push it all the way into the sim card slot as shown in pictures below

CARRIER board

Modem board

U.FL cable

EN-6 8800-1218 Rev C.

3.3. Flip the modem to correctly align the modem with respect to the carrier board. Make sure the U.FL

cable is placed as shown in the pictures below.

EN-7 8800-1218 Rev C.

3.4. Aligning the pins on the modem board, gently push the modem into the carrier board. A good

alignment is shown in the pictures below

3.5. Use LinkComm “Cell Diags” to verify that the new SIM card is working correctly.

EN-8 8800-1218 Rev C.

4. To remove the SIM card,

4.1. remove power to XLINK 100/500, if the cellular board is installed into the unit.

4.2. Place the cellular board on a clean surface, and remove the modem board from the carrier board.

4.3. Flip-over the modem board carefully without pulling the U.FL cable.

4.4. Remove the SIM card carefully from the sim card slot

4.5. If new sim card must be inserted, follow the instructions from sim card installation.

4.6. Carefully insert the modem board onto the carrier board, as shown in step 3.4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sutron Sender Handbücher

Sutron

Sutron Satlink 3 Handbuch

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung