Sven Studio Bedienungsanleitung

www.sven.ﬁ

OPERATION

MANUAL

studio

Active Three-way Hi-Fi Stereo

System with Digital Control

ENG

studio

Operation Manual

CONTENTS

1. DESCRIPTION .......................................................................................

2. SAFETY PRECAUTIONS ...........................................................................

3. PACKAGE CONTENTS .............................................................................

4. SPECIAL FEATURES ...............................................................................

5. SPEAKER SYSTEM PLACEMENT.................................................................

6. CONTROL PANEL ...................................................................................

7. ACTIVE SPEAKER REAR PANEL .................................................................

8. REMOTE CONTROL ................................................................................

9. CONNECTION .......................................................................................

10. OPERATION ........................................................................................

11. TROUBLE SHOOTING ............................................................................

12. TECHNICAL SPECIFICATION ...................................................................

Technical support is on www.sven.ﬁ

Congratulations on your purchase of the Sven speaker system!

Please read this operation manual before using the unit and retain this operation manual in a safe

place for future reference.

TRADEMARKS

All trademarks are the property of their legal holders.

NOTICE OF RESPONSIBILITY RESTRICTION

Despite the exerted eﬀorts to make this manual more exact, some discrepancies may occur. The

information of this manual is given on «as is» terms. The author and the publisher do not bear any

liability to a person or an organization for loss or damages which have arisen from the information,

contained in the given manual.

UNPACKING

Unpack the device carefully. Make sure there are no accessories left in the box. Check up the

device for damages; if the product was damaged during transportation, address the ﬁrm which

carried out the delivery; if the product functions incorrectly, address the dealer at once.

ATTENTION!

Do not switch on the speaker system immediately after you bring it into a room from environment

with negative temperature! After unpacking, the speaker system should be kept in conditions of

room temperature for at least 4 hours.

ENG

Active Three-way Hi-Fi Stereo

System with Digital Control

1. DESCRIPTION

STUDIO three-way Hi-Fi Multimedia Speaker System (MSS) with microprocessor control has a

built-in dual-channel Hi-Fi power ampliﬁer, high quality headphone ampliﬁer and high-grade surge

protector. The MSS is equipped with a built-in FM tuner, LED display, high quality USB DAC,

Distortion eﬀect module, and Karaoke module. Due to all this, STUDIO can be successfully used

for providing sound for dance ﬂoors and halls, holding rehearsals and concerts without using

additional costly equipment. The MSS is made in professional acoustics format, which means

using Speakоn connectors, solid metal grilles, powder painting, protective corner covers and carry

handles.

2. SAFETY PRECAUTIONS

•To avoid electric shock do not open the MSS and do not perform repairs by yourself.

•Do not allow circuit of wires (including grounded ones) between speakers, power ampliﬁer or

ground, for it causes damage of power ampliﬁer output stage.

•Do not put foreign objects inside the holes of the MSS. Make sure that needles, hair pins, coins,

insects etc. do not get inside.

•Protect the MSS from high humidity, water and dust. Do not locate it in areas with high level of

humidity and dust.

•Protect the MSS from heating: do not locate it near a heat source or expose to direct sunlight.

•Do not use gasoline, alcohol or other solvents when cleaning, since they may damage the

paint-coated surface of the MSS. Clean it with dry soft cloth only.

•If the MSS does not operate, unplug it and address your dealer.

3. PACKAGE CONTENTS

• Active speaker — 1 pc

• Passive speaker — 1 pc

•Acoustic cable — 1 pc

•2RCA to 2RCA signal cable — 1 pc

• USB cable — 1 pc

• Power cable — 1 pc

•FM antenna — 1 pc

•Remote control — 1 pc

•CR 2032 Battery — 1 pc

•Operation manual — 1 pc

•Warranty card — 1 pc

Caution! High voltage inside! To avoid the risk of electric

shock do not open or touch elements inside.

studio

ENG

Operation Manual

0,7 x

0,5 x

26°

70°

0,5 x

1,4 x

SPECIAL FEATURES

• Built-in dual-channel Hi-Fi power ampliﬁer

• Two CD and PC stereo inputs, USB input, headphone jack, two microphone jacks, guitar

connection input, two mono inputs for connecting electronic musical instruments

• Horn tweeters with increased sound pressure

• LED display

• Built-in FM tuner

• Karaoke module with digital control

• Distortion eﬀect module for electric guitars

• Full function remote control

• Master volume control and timbre control, headphone and microphone volume control,

reverberation level control

• High quality USB DAC for high ﬁdelity sound transmission via a USB cable by connecting to PC

• High quality headphone ampliﬁer

• Built-in high quality surge protector

• Carry handles

• MDF case of speakers

5. SPEAKER SYSTEM PLACEMENT

• Installation of STUDIO speaker system graded as Hi-Fi

(High Fidelity) class system is one of the most important

factors in achieving the best sound of the system. One

should know that location of speakers aﬀects tonal

balance, intensity and quality of bass components, sound-

stage depth and width, midrange sounds transparency. On

the one hand, the closer the speakers are placed to walls

and corners, the more powerful the sound of the bass

components is. On the other hand, the farther the speakers

are located from walls, the better the soundstage depth is

rendered. Angular position and height of speakers’ location

in relation to the listener aﬀect the timbral balance

formation (especially, treble), soundstage width, and

acoustic image focusing. Therefore speakers are best

located along the shorter wall of the room. The listener and

the speakers should be located in the corners of an

isosceles triangle as shown in the scheme, Fig.1 where

optimal Aand partial Bstereo eﬀect zones are shaded.

Angular position and height of the speakers’ location in

relation to the listener should be deﬁned by experiment.

The axes of the speakers should not intersect within the

area where the listeners are located.

Fig. 1. MSS location scheme

ENG

Active Three-way Hi-Fi Stereo

System with Digital Control

CONTROL PANEL

avolume: master volume control

btreble: treble level control

cbass: bass level control

dbalance: balance level control

emic 1: 1st microphone volume control

fmic 2: 2nd microphone volume control

greverb.: reverberation eﬀect control

hreverb. vol.: reverberation level control

idrive: distortion guitar eﬀect level control

jcontour: guitar timbre control

kaux 1: guitar mixing control

7. ACTIVE SPEAKER

REAR PANEL

amic 2: Ø 6.3 mm jack for connecting 2nd microphone

binput 1: mono input 1 for connecting electronic musical instruments

cinput 2: mono input 2 for connecting electronic musical instruments

dheadphones: Ø 6.3 mm jack for connecting headphones

eUSB: audio input for connecting USB cable

fCD: audio input for connecting players

gPC:

audio input for connecting PC

hFM-antenna: input for connecting FМ-antenna

iPOWER: power switch

jAC INPUT: input for connecting power cable

kSpeakon: passive speaker connection input

laux 2: microphones mixing control

maux 3: 1st electronic musical instrument mixing

control

naux 4: 2nd electronic musical instrument mixing

control

omic 1: Ø 6.3 mm jack for connecting 1st micro-

phone

pguitar: guitar input

qLED display screen

rinput: audio source selection button

sstandby: standby mode button

Fig. 2. Control panel

abcd feghik

srqop

lmnj

Note. Mixing control knobs k, l, mand nfunction only if microphones, a guitar or other

electronic musical instruments are connected to corresponding inputs.

studio

ENG

Operation Manual

Fig. 4. Remote control

Fig. 3. Rear panel

Remote control battery installation

• Open the battery compartment at the back of the RC.

• Put in the CR2025 battery (included).

• Close the battery compartment.

Notes:

• Use the remote control at an angle not more than

30° at a distance not more than 5 meters.

• Direct the remote control at the IR receiver display

on the active speaker.

• If the remote control does not work, check the

battery or replace the discharged battery with a new

one.

• Remove the battery from the remote control, if you

aren’t going to use it for a long time (more than a

week).

8. REMOTE CONTROL

aSTANDBY: standby mode button

bMUTE: sound oﬀbutton

c0 – 9: numeric keyboard buttons for selecting preset

radio stations

d+10: multiple factor button for selecting preset radio

stations numbered 10 and up

eTUNING«+/–»: radio frequency manual setting buttons

fFM: tuner switch-on button

gAUTO PRESET: tuner auto setting button

hMEMORY STATION+ /–: preset stations successive

selection buttons

iVOL+/–: master volume control buttons

jMIC1+/–: 1st microphone volume control buttons

k+/–: headphone volume control buttons

lMIC2+/–: 2nd microphone volume control buttons

mINPUT: audio source selection button

nMEM: button for presetting stations in the memory

of the tuner

abcd e

mic 2 input 1

POWER

OFF

FM antenna

input 2 headphones USB

CD PC

artist speakers system

ENG

Active Three-way Hi-Fi Stereo

System with Digital Control

FM-antenna

COMPUTER

Fig. 5. Connection diagram

9. CONNECTION

Speaker connection

• Before connecting, make sure that the MSS is unplugged.

• Connect the acoustic cable as shown in the diagram, Fig. 5. To connect the Speakon acoustic

cable to the female panel connector on the active or passive speaker, match the projections of the

male cable connector with the channels of the speaker female connector (Fig. 6). Push the cable

connector end into the female connector until stop, turn it clockwise until click and ﬁx the

connector. To disconnect the cable, pull the connector lock, then turn the cable connector counter-

clockwise and remove the cable.

Note. If the projections on the male connector end do not match the channels of the female

connector, do not apply excessive force to avoid damaging the cable.

PLAYER

mic 2 input 1

POWER

FM antenna

input 2 headphones USB

CD PC

artist speakers system

CD/MP3/DVD

2RCA to mini-jack signal cable

Acoustic cable

Passive speaker

2RCA to 2RCA signal cable

USB cable

studio

ENG

Operation Manual

Cable end with Speakon

cable connector

Connecting the MSS to audio sources

STUDIO Hi-Fi Multimedia Speaker System 2.0 can be connected to virtually any audio source (see

Fig. 5).

• Before connecting, make sure that the MSS is unplugged.

• To connect the MSS to a CD/DVD/MP3 player, use the included 2RCA to 2RCA stereo signal

cable. Connect the RCA-jacks of the signal cable to the CD input (f, Fig. 3) of the active speaker

rear panel, and then to the CD/DVD/MP3 player outputs. If your player has mini-jack inputs, use a

2RCA to mini-jack (Ø 3.5 mm) stereo signal cable or a mini-jack to 2RCA adapter (not included).

• To connect the MSS to a PC sound card, use a 2RCA to mini-jack (Ø 3.5 mm) stereo signal cable

or a mini-jack to 2RCA adapter (not included). For this, connect the RCA jacks to RCA PC input (g,

Fig. 3) of the active speaker rear panel, and the mini-jack – to the sound card output.

• To connect the MSS to a USB port of your PC or laptop, use the USB cable included in the

package contents. In order to do this, attach the USB cable connector to the USB input (e, Fig. 3)

on the active speaker rear panel, and insert the other connector of the USB cable to an available

USB port of your PC or laptop. The MSS has a built-in high quality USB DAC providing clear sound

transmission via a USB cable.

• Two microphones can be connected to the MSS: the 1st one – to the mic 1 input (o, Fig. 2) on

the control panel and the 2nd one – to the mic 2 input (a, Fig. 3) on the active speaker rear panel. A

guitar can be connected to the guitar input (p, Fig. 2) on the control panel, headphones – to

headphones input (d, Fig. 3) on the active speaker rear panel. Mono inputs input 1 (b, Fig. 3) and

input 2 (c, Fig. 3) on the active speaker rear panel serve to connect other electronic musical

instruments, except for an electric guitar.

Note. Mind the correct connection of all the inputs and outputs and proper ﬁxation of

connecting cables in the jacks, to avoid sound distortion during reproduction.

FM antenna installation and connection

• Insert the included room FM antenna into the FM antenna input (h, Fig. 3) on the rear panel of

the active speaker, as shown in the diagram, Fig. 5. Install the FM antenna in such a way that

reception quality is satisfactory, and then ﬁx the antenna in this position.

Speakon panel

connector

Speakon cable

connector

Connector lock

Channel

Channel Projections

Fig. 6

ENG

Active Three-way Hi-Fi Stereo

System with Digital Control

10. OPERATION

Switching On

• To switch on the MSS, insert the power cable into the input (j, Fig. 3), and then insert the power

cable plug into the mains socket. Shift the POWER On/ Oﬀswitch (i, ON position) on the rear

panel of the active speaker into ON position. Then press STANDBY button (a, Fig. 4) on the remote

control or STANDBY button (s, Fig. 2) on the control panel.

• Before switching on an audio source we recommend to adjust the master volume to its minimum

by pressing VOL– button (i, Fig. 4) on the remote control or by turning the volume knob (a, Fig.

2) on the active speaker control panel counterclockwise until stop.

Audio Source Selection

• To select an audio source, press INPUT SELECT button (m, Fig. 4) on the remote control or

INPUT button (r, Fig. 2) on the control panel. When the INPUT button is pressed, the LED

display on the control panel will successively show names of inputs: CD (Fig. 7), PC (Fig. 8), USB

(Fig. 9), referring to the connected audio source, or FM station, for example, «100» (Fig. 10).

IMPORTANT! If the MSS is connected via a USB port, the computer must ﬁnd this

connection and install (if necessary) corresponding drivers. Drivers are not required for

Windows XP/Vista/7.

MSS setting with audio sources connected

• Master volume can be adjusted by pressing VOL+ иVOL– buttons (i, Fig. 4) of the remote

control or turning the volume knob (a, Fig. 2) on the active speaker control panel. Volume

increasing/reducing will be shown on the LED display (See Fig. 11 and 12). The volume level ranges

from -99 (minimum, the sound can’t be heard) to 00 (maximum).

CD input on PC input on

FM input onUSB input on

Fig. 7

Fig. 9

Fig. 8

Fig. 10

Fig. 11 Fig. 12

studio

ENG

Operation Manual

Other settings, such as balance level between the right and left speaker, treble level, bass level,

microphone, headphone volume level, guitar or other electronic musical instruments (bass guitar,

synthesizer) volume level, can be adjusted with corresponding remote control buttons or active

speaker control panel knobs.

• Adjustment of balance between the left and right speakers is made with balance knob (d, Fig. 2)

on the control panel. The LED display will show the current balance, for example, L-02 or R-07 (Fig.

13 and 14). Using the balance knob adjust the desired balance between the speakers (Fig.15) –

LR00. The level can range from –15 to 00.

• Adjustment of treble level is made with treble band bass cknobs on the control panel. The LED

display will show the bass and treble level, for example, 02 or –08 (Fig. 16 and 17). Using the treble

and bass knobs, adjust the desired level. The level ranges from +14 to –14.

• Adjustment of volume level of microphones is made with mic 1 (e, Fig. 2) and mic 2 (f, Fig. 2)

knobs on the control panel. The LED display will show the microphones’ volume level (Fig. 18 and

19). Using the mic 1 and mic 2 knobs, adjust the desired volume level. For convenient use of the

MSS there is an option of quick microphone volume level adjustment with MIC1– / MIC1+ (j, Fig.

4) and MIC210 / MIC2+ (k, Fig. 4) buttons of the remote control. The level ranges from –99

(minimum) to 00 (maximum).

• Adjustment of headphone volume level is made with – and + buttons (k, Fig. 4) on the

remote control. The LED display will show the headphone volume level, for example, Р00 or Р-03

(Fig. 20 and 21). Using the – and + buttons, adjust the desired volume level. The level ranges

from -40 (minimum) to 00 (maximum).

Fig. 16 Fig. 17

Fig. 18 Fig. 19

Fig. 13 Fig. 14 Fig. 15

Inhaltsverzeichnis

Andere Sven Sprecher Handbücher

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung