Swann SSUS1000 Referenzhandbuch
FORM #651-6-15-1M
Installation Procedure for
MODEL SSUS1000
SWANSTONE UTILITY SINK
Read ALL instructions carefully BEFORE starting your installation
CAPACITY 17.50 GALLONS
1. Measure and cut counter hole for sink insertion 23-5/8” wide x
20-5/8” long. Test fit sink. File any areas which require widening.
2. After test fitting sink, remove from counter hole and install faucet
(not included) and drain assembly (see Figure 1).
3. In the installation of the SSUS1000, DO NOT use the white washer
in the installation process. Use of the white washer may cause the
drain to sit improperly and cause water to pool around the drain
area.
Helpful Hint .... for easy installation of final supply line
connections, it is suggested that, if possible, plumbing
connection to faucet be made at this point. Plumbing
connections to hot and cold supply line can then be made after
sink is secured to counter top.
4. Set sink into place and assemble bracket, washer, and nut
attachments (see Figure 2). Alternating from one to another,
tighten mounting bracket assembly nuts.
5. Some caulking residue may flow from under sink flange. This
residue can be wiped clean following instructions on silicone or
latex caulking tube.
6. Attach drain waste and faucet plumbing.
Mounting Assembly Figure 2
Mounting Point
Clip
Threaded Bolt
Drain Assembly
Figure 1
Swan
CORPOR AT I O N
TO BE REMOVED FOR USE BY OCCUPANT
3 3/4”
12 1/4”
NOTE
For easy installation of final supply line connections, it
is suggested that, if possible, plumbing connection to
faucet be made at this point. Plumbing connections to
hot and cold supply line can then be made after sink
is secured to counter top.
Read ALL instructions carefully BEFORE starting your installation
CAPACITY 7 GALLONS
1. Measure and cut counter hole for sink insertion 15-7/8” wide x
18-5/8” long. Test fit sink. File any areas which require widening.
2. After test fitting sink, remove from counter hole and install faucet
(not included) and drain assembly (not included). A standard
3-1/2” drain assembly is recommended.
3. Caulk along edges of 15-7/8” x 18-5/8” counter hole with 1/8”
bead of silicone or latex caulk (not included).
4. Set sink into place and assemble (see Figure 1). Alternate from
one threaded bolt to another until all bolts are tight.
5. Some caulking residue may flow from under sink flange. This
residue can be wiped clean following instructions on silicone
or latex caulking tube.
6. Attach drain waste and faucet plumbing.
Installation Procedure for
MODEL SSUS2000
SWANSTONE UTILITY SINK
IMPORTANT
It is recommended that a standard
3-1/2” drain assembly (not included)
be used to complete the installation
of the Swan DIT-S self-rimming
drop-in Tub.
TO BE REMOVED FOR USE BY OCCUPANT
Swan
CORPORATION
of the Swan SSUS2000.
3 3/4”
8 3/4”
10 1/2”
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Swann Küchen- und Badezimmerausstattung Handbücher
Beliebte Küchen- und Badezimmerausstattung Handbücher anderer Marken
Alpha Bidet
Alpha Bidet Alpha One Bedienungsanleitung
InSinkErator
InSinkErator H/HC3300 Installationshandbuch
Clou
Clou Xo type 1 Bedienungsanleitung
Kohler
Kohler Contra 26448T-4 Bedienungsanleitung
Grohe
Grohe Bridgeford 20 158 Bedienungsanleitung
Hans Grohe
Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Bedienungsanleitung