Swann ADW-350 Bedienungsanleitung
1
EN
ADW-350
Digital Wireless Security System
Quick Start Guide
Welcome!
Lets get started.
QH_350KIT110214E | © Swann 2014
Congratulations on your purchase of this Digital Wireless Security System from Swann. This
guide will familiarize you with the features and functionality of your wireless monitor and
camera kit and get you up and running as soon as possible. Once you’ve installed the monitor
and camera kit, read the guide on the reverse side to find details on setting up your system.
Before installing anything permanently, connect everything up and test the system - just to
make sure nothing was damaged during shipping!
1. DC 5V Power Input - For connecting the supplied
power adapter.
2. AV Out Port - Allows you to connect to your TV or an
external display device using the supplied AV cable.
3. SD Card Slot -Slot for inserting a standard SD card
(up to 32GB) to save SD card-based recordings.
4. USB Port - For recording videos to an external USB
storage device (up to 1TB).
1Getting to know the Monitor And Camera
21 3 4
MONITOR
MENU
OK
1
897
2 3 4 5
6
10
11
12
1. Power and Link LED Indicator - Left side lights up when the monitor
is turned on; blinks when the monitor is on standby mode. Right side
lights up when the monitor links successfully with the camera.
2. Display Mode - Change the arrangement of channels on your screen.
Options are: 2 x 2, single camera view and 1 + 3.
3. Trash Button - In the Playback Interface screen, press to delete the
selected video file. In live viewing mode, press to switch display between
the monitor and the TV (if connected via AV Out port).
4. Menu Button - Display the menu system, or return to a previous screen.
5. Arrows / OK Button - For navigating through the menu system and
confirming choices. In live viewing mode, the left/right arrows select
a channel (and audio source), while the up/down arrows act as volume
control. The selected channel is identified by a red “V” on the screen.
6. Power Button - Press and hold for 3 seconds to turn the monitor on or
off (note that while the monitor is off, recording is not possible).
7. Record Button - Immediately start recording (SD-card/USB device
must be inserted) of the selected channel, even if recordings were
not scheduled or triggered by PIR motion sensor. Press again to stop
recording.
8. Scan Mode Button - Scan between channels in 1 + 3 screen
layout where the current channel in focus is shown on the larger
display.
9. Playback Button - Shortcut to quickly access the Playback Interface
screen to watch recordings.
10. Antenna - The supplied antenna attaches to the gold connector here.
11. Stand - Lift out the stand by pushing the release tab.
12. Speaker -Audio transmitted from the camera will be heard from here.
12
4
3
5
CAMERA
1. Pair Button - This is used to pair the camera
with the monitor during pairing mode.
2. Power LED Indicator - Lights up solid red
when the camera is supplied power through
the power adapter.
3. Link LED Indicator -Lights up solid green
when the camera is paired with the monitor.
4. Power Connector -For connecting the
supplied power adapter.
5. Antenna Connector - For attaching the
supplied antenna.
2
A
Installing the Monitor and Camera Kit
Screw an antenna onto the gold connector on the back of the monitor and the
camera. For best reception, make sure the antenna is vertically positioned.
B
C
Attach the power adapter connector
labelled ‘RECEIVER ONLY’ to the DC 5V
Power input located on the side of the
monitor and then plug the power adapter
into an electrical outlet. The blue Power
LED on the monitor starts blinking when
the monitor is connected to a power
source.
Attach the power adapter connector
labelled ‘CAMERA ONLY’ to the DC 5V
Power input cable on the back of the
camera and then plug the power adapter
into an electrical outlet. The Power LED on
the back of the camera turns red when the
camera is connected to a power source.
3Powering up the Monitor
The camera(s) which come in the box are pre-paired with the monitor. You’ll only need to manually pair cameras if
you’re adding cameras, are troubleshooting or want to pair cameras with different channels. For more details on
pairing cameras, see the user manual.
Press and hold the Power button
on the front of the monitor until
the Swann “Loading” splash
screen appears. Wait a few
seconds for live video from the
camera to appear on the screen.
Follow the guide on the reverse
side to learn how to configure
basic settings for the system.
MENU
OK
4Mounting the Camera
When mounting the camera, bring the monitor with you because it’s easier to obtain the best view for the camera when
you can actually see what you are aiming at.
Place the base of the camera
stand in the location you
want to mount it and mark the
screw holes on the surface
to position the screws. Then,
using the included screws and
wall plugs, screw the camera
into place.
The camera comes with a built-in
stand, which you can mount to a wall
or any suitable vertical flat surface.
Adjust the viewing angle of the camera
by loosening the screws shown here
using the supplied L-wrench. Tighten
them once the camera is in the desired
position.
5(Optional) Connecting to your TV
Is your TV screen flickering? Navigate to Menu > System > TV System and make sure the selected setting (PAL or
NTSC) is the same as your TV’s video format.
The monitor’s AV Out port lets you connect to your TV to view live video and recordings on a
much bigger display.
Connect the black AV connector on the
AV cable to the AV Out port located on
the side of the monitor.
Connect the three color-coded
connectors on the AV cable to the
corresponding video and audio inputs on
Press the Trash button on the monitor to switch the
monitor’s display to your TV. Make sure you set your
TV to display from the AV input ports connected to the
monitor. MENU
OK
The Wireless Monitor’s On-screen Menu
allows you to access a variety of settings
(System, Record, Playback, Camera and
Alarm) for the system.
Navigating through the menus is easy; use
the Arrows to highlight options, the OK
button to confirm selections and the MENU
button to move back to the previous screen.
Now, let’s take a moment to run through
some important menu options that will
allow you to configure basic settings for the
system when you turn on the monitor for the
first time.
EN Configuring Basic System Settings
Read this guide to get started, then use the user manual to find out more about all the available menu options.
Andere Handbücher für ADW-350
1
Inhaltsverzeichnis
Andere Swann Sicherheitssystem Handbücher
Swann
Swann alpha Series Bedienungsanleitung
Swann
Swann HD Pro-Series Bedienungsanleitung
Swann
Swann SW351-CAC Bedienungsanleitung
Swann
Swann DVRx-2500 Bedienungsanleitung
Swann
Swann DVR4-2500 Bedienungsanleitung
Swann
Swann SW351-WSA Bedienungsanleitung
Swann
Swann SWDVK-840004D Bedienungsanleitung
Swann
Swann DVR4-1000 Bedienungsanleitung
Swann
Swann NightHawk Twin Pack SW233-WX2 Bedienungsanleitung
Swann
Swann Alpha D03C5 Bedienungsanleitung
Swann
Swann DVR8-4200 Bedienungsanleitung
Swann
Swann One Bedienungsanleitung
Swann
Swann Alpha D04C1 Bedienungsanleitung
Swann
Swann DVR Guardian SW244-UDC Bedienungsanleitung
Swann
Swann SwannSecure Bedienungsanleitung
Swann
Swann SSH-KIT03 Bedienungsanleitung
Swann
Swann DVR4-2550 Bedienungsanleitung
Swann
Swann RedAlert SW244-WDW Bedienungsanleitung
Swann
Swann PRO-640 Bedienungsanleitung
Swann
Swann USB 2.0 DVR Guardian Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
Blaupunkt
Blaupunkt SA 2700 Bedienungsanleitung
IDEAL
IDEAL Accenta Betriebsanleitung
AJAX
AJAX DoubleButton Bedienungsanleitung
Ecolink
Ecolink Siren+Chime Bedienungsanleitung
Digital Monitoring Products
Digital Monitoring Products XR150 Bedienungsanleitung
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung
DSC
DSC PC 4010 Betriebsanleitung