Swann NVR Bedienungsanleitung

NVR Quick Start Guide

QHGUAEYE040416E | © Swann 2016

Welcome! Lets get started.

READ ME

FIRST!

To start using your NVR, you need the following:

1) A high-definition TV capable of displaying 720p

or 1080p video. Look at the ports on the back of

your TV to make sure it has an HDMI input.

2) A router with a broadband Internet connec-

tion.

3) A mobile device (Android or iOS) to download

the free SwannView Link app.

Carefully unpack each item and discard any

packaging not required.

Congratulations on the purchase of your Swann NVR. This Quick Start Guide will assist you on getting your NVR up and

running as soon as possible. To make sure nothing was damaged during shipping, we recommend that you connect

everything and give it a try before you do a permanent installation.

Getting to know your NVR

1) Antenna Socket

2) Ethernet Port

3) Audio Out Port

4) VGA Port

5) HDMI Port

6) USB Ports

7) Antenna Socket

8) Power Port

9) Power LED

10) Hard Drive

LED

Look out for the light bulb icon, as this

provides tips on the operation of your

NVR.

Your NVR is designed to ventilate air

to keep it at an optimal temperature.

Keep your NVR free from obstructions

to allow it to ventilate properly.

PWR HDD

4 Channel HD Network Video Recorder

VGA

USB

AUDIO

OUT

LAN DC 12V IN

2 3 4 5 6 8

1 & 7) Antenna Socket: The supplied antennas connect

here. The antenna communicates with the supplied

cameras and it can also connect to your Wi-Fi network.

2) Ethernet Port: Connect this to your router so your NVR

can connect to the Internet (required for AP mode).

3) Audio Out Port: For connecting to a stereo or amplifier.

This is not required when using the HDMI port.

4) VGA Port: Connect this to your monitor with a VGA input

(VGA cable not supplied). This is not required when using

the HDMI port.

5) HDMI Port: Connect this to your TV with a HDMI input

(HDMI cable supplied).

6) USB Ports: Connect the mouse here. You can also

connect a storage device such as a USB flash drive to copy

recorded events or to perform a firmware upgrade.

8) Power Port: Connect the DC 12V power adapter here.

9) Power LED: Indicates your NVR has power.

10) Hard Drive LED: Will flash when the hard drive is

working.

FCC Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Caution: Any changes or modifications to this device not explicitly

approved by manufacturer could void your authority to operate this

equipment.Thisdevicecomplieswithpart15oftheFCC Rules.Operation

is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

What does this mean?

1) Located at the rear of your NVR are two antenna sockets.

There is also a single antenna socket at the rear of each

camera.

2) As there are several antennas provided, use the two

longer versions for your NVR and the shorter versions for

each camera.

3) Turn the antenna in a clockwise motion to connect.

Don’t use excessive force when connecting as it just needs

a firm connection to fasten (tools should not be required).

Leave the antennas in a vertical position for best reception.

HDMI USB

DC 12V

Step One: Installing the Antennas

1) Connect the Power Output on the Power Cable to the

Power Input on your camera. Repeat this step for each

camera provided.

2) Connect the Power Input on the Power Cable to the

Power Adapter. Repeat this step for each Power Adapter

provided.

3) Connect each power adapter to a power outlet then

press the outlet’s switch to the on position to supply power.

Reset: To restore factory default settings, press and hold

the reset button, connect power, continue holding for 10

seconds then release. Your camera will disconnect from

your NVR momentarily and then reconnect.

Ethernet Port: This port can be used to configure your

camera to your Wi-Fi network.

Ethernet Port

Reset

Power

Input

Power

Output

Power

Input

Power Cable

Power Adapter

Step Two: Connect your Cameras

Connect the supplied Ethernet cable to the Ethernet port (1) on your NVR then connect the other end to a spare port

(2) on your router. Don’t proceed to the next step until this is done.

Please note: It’s important that you do this as this allows your NVR to send email alerts, synchronise its

internal clock and for remote access using the SwannView Link app.

USB Internet 432

VGA

USB

AUDIO

OUT

LAN DC 12V IN

Ethernet Cable

Step Three: Connect to your Home Network

Connect the supplied mouse (1) to the bottom USB port (2). To copy your video recordings and to perform a firmware

upgrade, connect a storage device such as a USB flash drive (not included) to the top port.

Please note: Bluetooth and wireless mice and trackpad devices are not supported. Not all USB storage devices

are supported.

VGA

USB

AUDIO

OUT

LAN DC 12V IN

Step Four: Connect your Mouse

Connect the supplied HDMI cable to the HDMI port (1) on your NVR then connect the other end to a spare HDMI input

(2) on your TV. The labels on the back of your TV indicate which input you need to select when your NVR is turned on.

HDMI IN 1

HDMI IN 2

VGA

USB

AUDIO

OUT

LAN DC 12V IN

Press the A/V button on

your TV’s remote to select

the HDMI input.

HDMI Cable

Step Five: Connect to your TV

Connect the supplied power adapter’s power connection (1) to the power input (2) on your NVR first (this will minimise

sparking). Connect the power adapter to a power outlet then press the outlet’s switch to the on position to supply power.

VGA

USB

AUDIO

OUT

LAN DC 12V IN

All connections have now been completed. You should see the NVR on your TV with the Wizard displayed on-screen.

Follow “The Wizard” Quick Start Guide (the red coloured guide) to configure your NVR.

As your DVR is designed

to be always on, there is

no power button.

Step Six: Connect your Power Adapter

Andere Handbücher für NVR

Inhaltsverzeichnis

Andere Swann Sicherheitssystem Handbücher

Swann

Swann DVRx-2500 Bedienungsanleitung

Swann

Swann SW245-SBD Bedienungsanleitung

Swann

Swann DVR4-4550 Bedienungsanleitung

Swann

Swann Alpha D04C1 Bedienungsanleitung

Swann

Swann PRO-681 Bedienungsanleitung

Swann

Swann 4 Channel DVR4-2000 Bedienungsanleitung

Swann

Swann SW351-KCH Bedienungsanleitung

Swann

Swann ADW-200 Bedienungsanleitung

Swann

Swann NightHawk Twin Pack SW233-WX2 Bedienungsanleitung

Swann

Swann PLATINUM HD Bedienungsanleitung

Swann

Swann NIGHTHAWK 3-Feb Kurzanleitung

Swann

Swann PRO-530 Bedienungsanleitung

Swann

Swann RedAlert SW244-WDW Bedienungsanleitung

Swann

Swann ADW-340 Bedienungsanleitung

Swann

Swann SWWHD-INTSOL Bedienungsanleitung

Swann

Swann SW351-CAC Bedienungsanleitung

Swann

Swann 960H Pro series Bedienungsanleitung

Swann

Swann USB 2.0 DVR Guardian Bedienungsanleitung

Swann

Swann Automobile Alarm Kurzanleitung

Swann

Swann SW231PC4 Bedienungsanleitung

Swann

Swann DEFEND & DETER SWA43-D12C16 Bedienungsanleitung

Swann

Swann SWDVK-840004D Bedienungsanleitung

Swann

Swann SW212-HXD Bedienungsanleitung

Swann

Swann HD Pro-Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung