Swann SWNVK-874004-UK Bedienungsanleitung

Security Made Smarter

PLATINUM DIGITAL HD

Professional HD

Security System

INSTRUCTION MANUAL

Important Information

FCC Verification

This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio

or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

• These devices may not cause harmful interference

• These devices must accept any interference received, including in-

terference that may cause undesired operation

Important Notice: All jurisdictions have specific laws and regulations re-

lating to the use of cameras. Before using any camera for any purpose,

it is the buyer’s responsibility to be aware of all applicable laws and reg-

ulations that prohibit or limit the use of cameras and to comply with the

applicable laws and regulations.

FCC Regulation (for USA): Prohibition against eavesdropping

Except for the operations of law enforcement officers conducted under

lawful authority, no person shall use, either directly or indirectly, a de-

vice operated pursuant to the provisions of this Part for the purpose

of overhearing or recording the private conversations of others unless

such use is authorized by all of the parties engaging in the conversation.

Warning: Changes or modifications made to this device not approved

expressly by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important Safety Instructions

• Make sure product is fixed correctly and stable if fastened in place

• Do not operate if wires and terminals are exposed

• Do not cover vents on the side of the device and allow adequate space

for ventilation

• Only use the power adapter supplied with your NVR

Password Information

This NVR does not have a default password. A password is created dur-

ing the Setup Wizard. If password protection has been enabled and you

have forgotten your password, you can enter a super password. Click

“Forgot Password” then input your NVR’s MAC address without the co-

lons, for example, EC71DBE32877 - see page 40 for more information.

Your NVR’s MAC address can also be obtained using SwannView Link for

Windows. Please download it from our website (support.swann.com).

About this Manual

This instruction manual is written for the NVR-7300/7400 and was ac-

curate at the time it was completed. However, because of our on-going

efforts to constantly improve our products, additional features and func-

tions may have been added since that time. We encourage you to visit

our website to check for the latest updates and product announcements.

Contents

Important Information 2

Contents 3

Chapter 1: Live View 4

Live View 4 & 8 Channel 5

Live View 16 Channel 6

Chapter 2: Menu 7

Menu Layout 8

Chapter 3: Camera Configuration 9

IP Channel 10

Display: Camera 11

Creating a Privacy Mask 13

Camera Parameter 14

Recording: Encode 15

Alarm: Motion 16

Motion Detection 17

Motion Detection Schedule 18

Motion Detection Tips 19

Alarm: Video Loss 20

Video Loss Schedule 21

Controlling an Optical Zoom & Auto-focus Camera 22

Chapter 4: Recording Configuration 23

Recording: Encode 24

Recording: Option 25

Recording: Schedule 26

Chapter 5: Playback & Backup 27

Search: Playback 28

The Playback Interface 29

Search: Event 31

Search: Backup 32

Chapter 6: System Configuration 33

System: General 34

System: User 35

System: Maintenance 36

Alarm: Exception 37

Device: HDD 38

Display: Output 39

Network: General 40

Network: Advanced 41

Chapter 7: System Status 42

Search: Log Search 43

Network: Status 44

Device: S.M.A.R.T 45

System: System Information 46

Glossary 47

Warranty Information 51

Helpdesk & Technical Support 52

Live View

Live View is the default display mode

for your NVR. Each camera connected

will be displayed on-screen. You can

check the status or operation of your

NVR and cameras using the icons and

Menu Bar on the Live View screen.

Right-click the mouse to access the

Menu Bar.

Camera2Camera1

09/12/2014 10:30:15 Tue09/12/2014 10:30:15 Tue

09/12/2014 10:30:15 Tue 09/12/2014 10:30:15 Tue

09/12/2014 10:30:15 Tue

Camera2

Security Made Smarter

PLATINUM DIGITAL HD

Professional HD

Security System

INSTRUCTION MANUAL

Live View: 4 & 8 Channel

1. Opens the Menu.

2. Click to view a single camera.

3. Click to view four cameras.

4. Click to view eight cameras (1 +

7 formation).

5. Click to view eight cameras (3 x

3 formation).

6. Click to view the next screen in

single or four camera view.

7. Click to enable PIP mode.

8. Click to manually record the

selected camera.

9. Click to access the Setup Wiz-

ard.

Camera Toolbar

Status Icons Camera2Camera1

09/12/2014 10:30:15 Tue09/12/2014 10:30:15 Tue

09/12/2014 10:30:15 Tue 09/12/2014 10:30:15 Tue

1 2 3 4 5 6 7 8 9

Menu Bar

Double-click a live

video channel to

view full screen.

Click & drag a live

video channel to

reposition it.

Live View: 16 Channel

1. Opens the Menu.

2. Click to view a single camera.

3. Click to view four cameras.

4. Click to view eight cameras (1 +

7 formation).

5. Click to view eight cameras (3 x

3 formation).

6. Click to view sixteen cameras.

7. Click to view the next screen in

single or four camera view.

8. Click to enable PIP mode.

9. Click to manually record the

selected camera.

10. Click to access the Setup Wiz-

ard.

Camera Toolbar

Status Icons Camera2Camera1

09/12/2014 10:30:15 Tue09/12/2014 10:30:15 Tue

09/12/2014 10:30:15 Tue 09/12/2014 10:30:15 Tue

1 2 3 4 5 6 7 8 109

Menu Bar

Double-click a live

video channel to

view full screen.

Click & drag a live

video channel to

reposition it.

The Menu is where you control the

various actions and options that are

available on your NVR. You can also

access previously recorded video

for playback and to export to a USB

storage device such as a flash drive.

To maintain system integrity, a firm-

ware upgrade can be performed when

available and access to the Shutdown

menu to restart or safely turn off your

NVR.

Menu Layout

The various actions and options

that are available, are categorised

on the left-hand side of the Menu.

Clicking each category will reveal a

number of tabs or sub-categories

that can be changed from their de-

fault value.

Some options may have additional

menus that can be accessed.

To shutdown, reboot or lock

your NVR, click the “Shutdown”

button. To ensure the integri-

ty of your data and recordings,

always select “Shutdown” when

powering off your NVR.

To exit or access the

previous menu, right-

click the mouse.

Camera Configuration

The majority of the camera configura-

tion options available are in the “Dis-

play”, “Recording” and “Alarm” men-

us that are accessible from the Menu.

You can change the resolution and

bitrate settings as well as the image

settings for brightness, contrast and

more. Your NVR has several controls

for Motion Detection, Video Loss and

the ability to create one or more pri-

vacy masks.

IP Channel

The IP channel function displays a list of cameras that are either con-

nected directly to your NVR, or connected directly to your network. The

name, IP address, channel number, status, user name and password

of each camera is displayed. It’s not necessary to change the camera’s

user name and password.

Auto Add: This option is enabled by default. Your NVR will automatically

detect and display cameras connected directly to your NVR, or connect-

ed directly to your network.

Scan: Click this button to update the list of cameras detected.

• Don’t forget to click “Apply” to save settings.

• Click “Cancel” to exit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swann Sicherheitssystem Handbücher

Swann

Swann SWDVK-840004D Bedienungsanleitung

Swann

Swann DVR16-8600 Combo Bedienungsanleitung

Swann

Swann DVR4-2500 Bedienungsanleitung

Swann

Swann SW244-SKI Bedienungsanleitung

Swann

Swann Wireless OutdoorCam SW231-WDC Bedienungsanleitung

Swann

Swann Advanced SWDVK-825508C Bedienungsanleitung

Swann

Swann SWIFI-ISIREN Bedienungsanleitung

Swann

Swann RL-0507A Bedienungsanleitung

Swann

Swann Mobile viwer Bedienungsanleitung

Swann

Swann DVR Guardian SW244-UDC Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Swann

Swann SSH-KIT03 Bedienungsanleitung

Swann

Swann alpha Series Bedienungsanleitung

Swann

Swann DVR-1590 Series Bedienungsanleitung

Swann

Swann DVR4-1100 Bedienungsanleitung

Swann

Swann RedAlert SW242-WDW Bedienungsanleitung

Swann

Swann PLATINUM HD Bedienungsanleitung

Swann

Swann DVR4-2550 Bedienungsanleitung

Swann

Swann Alert DVR Camera Kit Bedienungsanleitung

Swann

Swann SWVAK-834254C Bedienungsanleitung

Swann

Swann Alert DVR Camera Kit Bedienungsanleitung

Swann

Swann MALARM1301012E Bedienungsanleitung

Swann

Swann SW347-WAK Bedienungsanleitung

Swann

Swann PRO-580 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung