Swisher L116-336001 Bedienungsanleitung

COMMERCIAL PRO

60” FAST FINISH

TRAIL MOWER

OWNER’S

MANUAL

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE., WARRENSBURG MO 640 3

PHONE 800-222-8183 FAX 660-747-8650 EMAIL CustomerCare@SwisherInc.com

MODEL NO.

FC14560CPKA

FC14560CPKA-CA

Assembly

Operation

Service and Adjustment

Repair Parts

www.swisherinc.com

20 27 REV 16-336

STARTING SERIAL #:

L116-336001

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

ade I The

USA

of US and Global Parts

ꁆ ﵇﵇

ˆ 

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for the period's shown below beginning from the date

of purchase by the original consumer purchaser. We will repair or replace, at our discretion,

parts found to be defecti e due to materials or workmanship. This warranty is subject to the

following limitations and exclusions:

As required y CFR § 1060.120, the fuel system related components, which have een

certified to this equipment y SAI are to e free of defects in material and workmanship for a

period of two (2) years from the date of purchase y the original consumer purchaser.

1) Engine Warranty All engines utilized on our products ha e a separate warranty

extended to them by the indi idual engine manufacturer. Any

engine ser ice warranty is the responsibility of the engine

manufacturer and in no way is Swisher or its agents responsible

for the engine warranty. The Kawasaki Engine Ser ice Hotline is

1-877-364-6404 or email kawpower-website@kmc-usa.com

2) Commercial Use This product has a 1yr Limited Commercial - 2 Year

Limited Consumer on All Non-Engine Parts from the date

of purchase.

3) Limitations This warranty applies only to products, which have een

properly assem led, adjusted, and operated in accordance with

the instructions contained within this manual. This warranty

does not apply to any product of Swisher that has een su ject

to alteration, misuse, a use, improper assem ly or installation,

shipping damage, or to normal wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal

adjustments, and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an

authorized service dealer. All transportation charges, damage, or loss incurred during

transportation of parts su mitted for replacement or repair under this warranty shall e orne

y the purchaser. Should you have any questions concerning this warranty, please contact us

toll-free at 1-800-222-8183. The model num er, serial num er, date of purchase, and the

name of the authorized Swisher dealer from whom you purchased the mower will e needed

efore any warranty claim can e processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty

may last, so the a ove limitations or exclusions may not apply to you. This warranty gives

you specific legal rights and you may have other rights, which vary from state-to-state. This is

a limited warranty as defined y the Magnuson-Moss Act of 1975.

˨

SAFETY PRECAUTIONS

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to prevent

accidental starting the engine when setting up, transporting, adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and sta ility of this machine. Know the positions and operations of all

controls efore you operate this machine. Check all of the controls in a safe ar

ea efore starting to work with

this machine.

• Allow only responsi le adults who are familiar with these instructions to operate this machine. Never allow

children to operate this machine.

• Clear the area of o jects such as rocks, toys, wire, etc. that can e picked up and thrown y the lade.

• Be sure the area is clear of other people efore mowing. Be aware of the mower discharge direction and do

not point at anyone. Stop the machine if anyone enters the mowing area. Children are often attracted to the

machine and the mowing activity. Never assume that children will remain where you last saw them.

Keep

children under the watchful care of another responsi le adult.

• No riders!

• Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

• Do not mow in reverse. Always look down and ehind efore and while acking.

• Turn off the lades when not mowing. Before leaving the machine, turn off the lades and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has een dropped or damaged in any manner or if the mower vi rates

excessively. Excessive vi ration is an indication of damage. Repair mower as necessary.

• Dress properly. Do not operate the mower when arefoot or wearing open sandals. Wear only solid shoes

with good traction when mowing.

• Do not operate the machine while under the influence of alcohol or drugs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an o ject. Repair, if necessary, efore restarting.

• Never make adjustments or repairs with the engine running.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands, feet, and throw

objects. Failure to observe the following safety instructions could result in serious

injury or death.

矐ڱ

SAFETY DECALS

Replace decals immediately if damaged. Order y part num er from Swisher.

OD45- Warning Decal

OD11- No step Decal

OD55- Triangle Danger Decal

OD33- Speed Decal

OD29- Danger Decal

OD43- Flying De ris Decal

*Battery cover not shown

Battery Mounting Detail

A U1 battery is required

(not included). Position

battery hold down

bracket as shown.

Tighten nuts so battery

will not shift position.

REQUIRED ASSEMBLY

FRONT WHEEL CASTER ASSEMBLY

1. Remove single nut and washers from caster shaft.

2. Place one washer (NB195) on the shaft of the caster/wheel su assem ly.

3. Slide same shaft through the earing/frame with wheel towards the ground.

4. Place the other washer (NB195) on the shaft; it should e resting on the top earing.

5. Add thin washer (17x195).

6. Thread nyloc jam nut onto shaft.

7. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut. Over-

tightening

of this nut will bind caster.

8. Repeat process for other front side.

9. Push on plastic dust covers over nut and thin washer until it snaps into place.

REAR WHEEL ASSEMBLY

1. Remove cotter pin from axle and remove thin washer (NB149) from axle. Leave two

NB178 washers on axle.

2. If necessary (to take up space) slide extra washer (NB178) over axle, then wheel (with

valve stem out).

3. Slide on washer (NB149) and replace cotter pin in end of axle.

4. Bend cotter pin so it will not fall out.

5. Repeat process for other wheel.

OFFSET & CENTER TOW HITCH BAR ASSEMBLY

1. Lay out parts according to the diagram.

2. Insert part 661A into part 662 and pin with the hitch pin (H11).

Insert part 661 into part 661A. Choose from the 3 holes to set the desired hitch length. Pin

with a hitch pin (H11).

4. Part 662 slides into the front tu e of the frame. Again, choose from the 3 holes to arrange

desired offset. Pin with a hitch pin (H11).

5. Eliminate step 2 for hitching from the center racket. Only one method can e used at a

time.

끆 ﵇﵇

ˆ 

OPERATING YOUR TRAIL MOWER

INTENDED USE

This Trail Mower is designed to produce a quality finish cut on lawns, golf courses, etc. It is

not designed to clear rush or cut saplings. Your Trail Mower should e towed ehind an

ATV, a golf cart, lawn tractor, or similar approved vehicle. It is not meant for speeds

exceeding 5 mph.

ATTACHING TRAIL MOWER TO TOW VEHICLE

• Place mower ehind vehicle and ack vehicle up to desired attaching position.

• When offsetting Trail Mower do so to side opposite the discharge of the tow vehicle.

• Attach tow hitch (661) to the swivel hitch with hitch pin (H11). Make certain hitch

pin goes completely through each piece and is clipped to prevent accidental

separation.

• Attach red safety tether (H9C) to oth the towing vehicle and to the Trail Mower

toggle switch (685SP), located on the left attery side cover (17614). Its purpose is to

manually stop mower engine or to stop mower engine in case the two machines

ecome separated. (See Motor Base Detail page 14).

• It is extremely important the safety tether is secured properly to both the toggle

switch and the towing vehicle.

STARTING THE ENGINE

See engine manufacturer’s instructions for the type and amount of oil and fuel used. Trail

Mowers with electric start engines will need a attery (sold separately). Swisher

recommends using a standard “U 1 R” lawn & garden attery.

The operation of any mower can produce foreign o jects to e thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles efore starting any cutting machine and

while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a iolation of

California Public Resource Code Section 4442 to use or operate the engine on any forest-co ered,

brush-co ered, or grass-co ered land. Other states or federal areas may ha e similar laws.

ڷ

•

Engine must e level to accurately check and fill oil. Do not overfill.

• Make sure the tow vehicle parking rake is set, mower is level, and lades are disengaged.

• Check spark plug wire, oil, and fuel.

• Check all electrical connections (See Schematics).

• Make sure toggle switch is turned “ON” and the red tether is properly attached.

• Set engine idle to “CHOKE” position.

• With feet clear of mower deck, turn key switch to the “START” position and release when

engine egins to run.

• Set engine idle at desired RPM.

BREAKING IN YOUR MOWER

• Set vehicle parking rake or chock wheels to prevent accidental rolling.

• Start engine properly.

• Slowly, engage lade control.

• In a safe environment, i.e. no children, allow lades to rotate and engine to idle for 5

minutes. This reaks in the elts and the engine.

• Stop mower properly.

MOWER HEIGHT ADJUSTMENT

• Adjust while mower is not running.

• The cutting range is approximately 1” to 5.5”. The height should e measured from the

ground to the lade tip without the engine running.

• Rotate height adjust crank handles (H7N) in a clockwise direction to lift the mower deck. A

counter-clockwise direction is used to lower the mower deck.

• Make sure the height adjustment is the same at side crank handles. For est results, see

“SUGGESTED PRACTICE” section. Graduated scales are for reference only, not the

actual cutter height.

• Place crank handle in a retracted position to maintain height adjustment.

STARTING TO MOW

• Adjust the cutting height.

• Dou le check vehicle to mower attachment.

• Start mower engine properly.

• Slowly, activate the lade engage lever (18976

) y rotating it forward and left until the lever

locks into place.

• Carefully mount tow vehicle and start mowing slowly.

STOPPING THE MOWING SESSION

• Pull safety tether to shut toggle switch “OFF”. If the engine fails to stop or if the safety

tether has ecome inopera le, then use Alternative Stopping Method.

CAUTION!

SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM

SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS TO THE MOWER.

ڷ

ALTERNATIVE STOPPING METHOD

• Bring vehicle to complete stop, shut off engine, and set parking rake.

• Disengage lade engage lever (18976).

• Manually shut toggle and key switches to their “OFF” positions.

• Always remem er to remove keys to avoid irresponsi le usage.

TRANSPORTING MOWER

• Stop mower properly.

• Place mower deck in its highest position.

• If transporting without the use of a tow vehicle, then remove spark plug wire and

place where it cannot contact the spark plug.

SUGGESTED MOWING PRACTICES

• Operate mower engine at full throttle to assure the est cutting performance and

maximum material discharge.

• Allow wet grass to dry. Clumps of wet grass will collect under the mowing deck.

• Mowing should e started with tow vehicle in low gear and increased only as safe

mowing conditions permit. This speed should not exceed 5 mph.

•

The average lawn should e cut to approximately 2.5” during the cool season and to

over 3” during the hot months.

• For a healthier lawn and etter aesthetics, your lawn should e mowed often and

after moderate growth.

• When cutting high or dense grass areas go slowly. Some areas may need to e

mowed twice. The second cut should e at 90 degrees to the first, if possi le.

• Mowing thick or high grass. Raise rear height crank handles to .5”-

.75” a ove the

other two handles.

• Creating a manicured lawn. Lower rear height crank handle to .25”-.5” elow

front of deck. This allows grass lades to e cut twice. It also continually cuts

clippings to produce a mulching effect.

GENERAL TROUBLE SHOOTING

• The mower is not cutting level.

o Level deck, making sure the side crank-handles are equal.

o Check air pressure of all tires; make sure they are equal, and to

manufactures specifications.

o Examine lades for damage, while mower engine is not running.

• The engine will not start.

Disengage lades, turn toggle switch to “ON” position, check attery and all

other electrical connections, and inspect spark plug and wire.

o Check for fuel in the engine.

• Engine runs poorly.

o See engine manual.

o Check throttle adjuster.

o Replace fuel, clean fuel filter and fuel line.

IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE THE

MOWER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT YOU ARE

NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER PROBLEMS.

˨

MOWER MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this Trail Mower does not cover items that have een su jected to operator a use or negligence.

To receive full value from the warranty, operator must maintain unit as instructed in this manual.

Some adjustments will need to e made periodically to maintain your unit properly.

All adjustments in this manual should e checked at least once each season.

Periodically inspect and clean excessive de ris inside the attery cover (17340) and elt covers (18391

). Disconnect

spark plug wire efore cleaning.

BEFORE EACH USE

• Check engine oil level on a level surface. Check twice to insure an accurate reading.

• Check condition of air filter; clean and replace as necessary.

• Check lade operation; keep lades in good condition.

• Check for loose fasteners and tighten them as needed.

AFTER EACH USE

• Keep lades sharp.

• Remove fresh grass clippings with garden hose.

• Grass clippings hardened to the underside should e scraped out with a putty knife.

• Keep fluids at proper levels.

• Cover unit to prevent rain or other de ris uildup. Definitely cover the engine.

BEFORE AND/OR AFTER EACH SEASON

• Replace the spark plug.

• Clean or replace the air filter.

• A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run etter and last

longer.

• Check lades and elts for wear. Replace as necessary.

STORAGE RECOMMENDATIONS

CAUTION!

Do not store engine indoors or other poorly ventilated area. Keep engine away from gas appliances

where fumes could contact open flame, pilot lights, or sparks.

If engine is to be stored for 30 or more days, prepare unit as follows:

• Drain fuel outside into an approved container.

• Start engine properly and run until unit is out of fuel.

• Let engine cool.

• Remove remaining gasoline from car uretor and fuel tank to prevent gum deposits from forming within

the engine. Gum deposits can cause malfunction in the engine.

• Store mower with lades disengaged to prevent elts from eing permanently stretched.

BLADE CARE AND SERVICE

For est results cutter lades must e kept sharp. The lades can e sharpened with a few strokes of a file or

grinding wheel. Do not attempt to sharpen lades while they are on the mower. Disconnect spark plug wire before

servicing unit.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are tight.

Only a qualified mechanic should e used for any

adjustments, disassem ly or other kind of repairs.

˨

FRAME ASSEMBLY

ITEM # QTY .

PART NO.

DESCRIPTION

1 1 3664 Bar - Right Sway

1 3665 Bar - Left Sway

3 1 17600* Weldment - T60 Frame

4 F4157WK Wheel/Tire 5/8" Bearing 13/5/6 NHS; Blk

5 1 66 * Weldment - Tongue Offset Ext ension

6 1 661A* Weldment - Solid Stock Hitch

7 1 661* Weldment - Tongue Hitch Ext ension

8 -- See Caster/Wheel Assembly Detail

ITEM # QTY. PART NO. DESCRIPTION

9 6 NB1 6 Pin - 1/8" X 1" Cott er

10 4 T PB Bushing - Plastic

11 4 NB178 Washer - 5/8 ID X 1 OD 10 GA

1 NB149 Washer - 5/8 ID X 1 OD 14 GA

13 4 H11 Pin - Safety Hitch

14 3 10579 Bushing -Stepped Height Adjust

15 3 H7N Assembly - Height Adjustment

16 3 10038 Bolt - Eye

ONLY INCLUDED ON “CA MODELS

(FOR CALIFORNIA ONLY)

Item # Qty Description Part #

1 1 Carbon Canister - 2.50 Gallon, 3/16 Line 18224

2 2 Cable Tie - Carbon Canister 18219

3 4 Nut - 10-24 Nylon Lock 024900

4 2 Bracket - Carbon Canister, ZT 17127

5 4 Screw - 10-24 X 3/4 Phil Truss Head ZP 024203

Item # Qty Description Part #

1 2 Ubolt - SQ , 3/8-16X2.437 X 3 Lg GR 5 ZY 12447

2 2 Nut - Nylock 1/4-20 NB180

3 4 Nut - Nyloc 3/8-16 ZY NB182

4 1 Mount - For EPA/CARB Gas Tank 18331*

5 1 Fuel Tank - 2.5 Gallon, Carb 18214

6 1 Cap, Fuel - 2.50 Gallon, Carb Sealed 18221

7 1 Bracket - Fuel Tank 18225

8 2 Bolt - Serr Flange 1/4-20 X 1 3/4 GR5 ZY 18236

GAS TANK

ASSEMBLY DETAIL

Part # Description

11782 Line - Fuel, Bulk, 1/4" Low Perm

18232 Line - Fuel, Bulk, 3/16" Low Perm

18223 Clamp - Fuel Line 13/32 OD, 3/16 ID Tube

AS021 Tie, Black 5 1/2"

Parts Not Shown

When ordering replacement parts

*USE PAINT CODE: GT=GRAY TK=BLACK

SEE HEIGHT ADJUST

HANDLE DETAIL

SEE CASTER/WHEEL

ASSEMBLY DETAIL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher ST67522CC Bedienungsanleitung

Swisher

Swisher POL 10550 Bedienungsanleitung

Swisher

Swisher ZT2866A-CA Bedienungsanleitung

Swisher

Swisher ZT2460 Z-MAX Bedienungsanleitung

Swisher

Swisher ST60022 Bedienungsanleitung

Swisher

Swisher ZT1436 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBT18560 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC14560 Bedienungsanleitung

Swisher

Swisher FC11544CL Bedienungsanleitung

Swisher

Swisher Predator WB80024 Bedienungsanleitung

Swisher

Swisher ZT18542A Bedienungsanleitung

Swisher

Swisher 97-056001 Bedienungsanleitung

Swisher

Swisher ZT2766 Bedienungsanleitung

Swisher

Swisher T1260F Bedienungsanleitung

Swisher

Swisher RT10544, RT80044 Bedienungsanleitung

Swisher

Swisher ZTR2460BS-CA Bedienungsanleitung

Swisher

Swisher COMMERCIAL PRO Bedienungsanleitung

Swisher

Swisher PREDATOR Bedienungsanleitung

Swisher

Swisher ZT2452A Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher T11544A Bedienungsanleitung

Swisher

Swisher Trim-N-Mow Plus STS67522BS Bedienungsanleitung

Swisher

Swisher QB Quadboss QBFC10544 Bedienungsanleitung

Swisher

Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung