Swiss Madison SM-STS31 Bedienungsanleitung

www.swissmadison.com | 1-434-623-4766 | [email protected]

INSTALLATION INSTRUCTIONS

Aqua Non-Electric Smart Toilet Seat Bidet

@SwissMadison

#WellMadeForever

well made for e v e r

—1 —

If you have any questions or concerns please contact us:

1-434-623-4766

[email protected]

PRIOR TO INSTALLATION:

· Inspect bidet to ensure no damages have occurred while in shipping.

· Observe all plumbing and building codes in accordance with your state and local requirements.

· All dimensions are nominal! Be sure to measure your toilet seat prior to installation.

· The step-by-step guidelines in the installation instructions are a general reference. Should there be

any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss

Madison products by hiring a licensed professional.

· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper

tools and always wear proper personal safety accessories for your protection.

· Please use the new hose sets supplied with the product. Do not use other hose sets with the product.

· Open angle valve to clear any impurities in the pipe prior to installation.

· Water supply pressure must be 0.07-0.8 MPa.

INCLUDED PARTS:

SUGGESTED TOOLS & MATERIALS:

Pliers Screwdriver Bucket &

Rag

SMART SEAT BIDET INSTALLATION INSTRUCTIONS

Inlet Hose

with Filter

T-PipeSmart Seat

Bidet Adjustment

Sheets

Fixing

Plate

Nuts &

Bolts Expansion

Bolts

—2 —

SMART SEAT BIDET TECHNICAL SPECIFICATIONS

SKU

Backflow Prevention

Water Inlet

Wash Water Flow

Water Supply

Bidet Water Flow

Water Pressure Range

Check valve, vacuum breaker

Static pressure: 0.07 - 0.8 MPa, Dynamic pressure: above 0.03 MPa

Direct from water pipes

Side

0.09 gal/min - 0.48 gal/min

SM-STS31

Water inlet on the left

Water inlet on the right Dismantlement

button

Bowl

Water inlet hose

Shutoff valve

T-pipe

Lever

Water tank

Water supply hose

Seat cover

Seat

Bidet nozzle

Wash nozzle

PRE-INSTALLATION

INSTALLATION

1. Remove Old Seat

· Remove old seat according to

manufacturer’s instructions.

2. Install Mounting Hardware

· Insert expansion bolts into ceramic holes.

—3 —

2. Insert into Fixing Plate

· Insert the connecting bolts in the holes of

adjustment sheets in the holes of the fixing plate

as shown.

1. Insert Connecting Bolts

· Insert the connecting bolts in the holes of

adjustment sheets as shown.

CAUTION:

· The water pressure limit is from 0.07 to 0.8 MPa, please use as instructed.

· The water shutoff valve should be near where the product can be installed and dismantled.

SMART SEAT BIDET INSTALLATION INSTRUCTIONS

—4 —

3. Install Installation Template

· Install the installation template on the toilet as shown.

4. Attach the Adaptable Panel

Installation A:

· Place the fixing plate over the expansion bolts, followed by the adjustment sheets then screws.

· Tighten screws with screwdriver.

Installation B:

· Place the fixing plate over ceramic holes, followed by the adjustment sheets then screws.

· Tighten nuts underneath screws.

NOTE: Keep the side labeled “FRONT” facing up.

SMART SEAT BIDET INSTALLATION INSTRUCTIONS

—5 —

6. Turn off Water

· Close the water valve and detach water pipe from the water tank.

· Connect the T-pipe to the water tank.

· Make sure that rubber sealing ring is inserted between the T-pipe and the water tank.

5. Remove Installation Template & Install Product

· Remove installation template.

· Keep the fix slots under the product aim at slots on the fixing plate. Push the product to the end as

shown below. Then complete installation.

SMART SEAT BIDET TECHNICAL SPECIFICATIONS

fix slots

—6 —

7. Connect Water Pipe to the T-Pipe

NOTE: Please remove the regulator cover and regulate o-ring under the following conditions:

a. When the water dynamic pressure is lower than 0.05 MPa.

b. When the nozzle cannot work normally and water is low.

· Take out regulator with pliers.

· Remove the regulator cover and regulate o-ring except the sealing o-ring.

· Insert the regulator component into the inlet pipe.

CAUTION: Must use the regulator cover and regulate o-ring when the water pressure is bigger than 0.1 MPa.

8. Connect Water Hose

· Press the filter and washer at the two ends of water hose into the threaded area, then connect the main

body and T-pipe with water hose.

· Turn on water and check for leaks.

WARNING:

Do not lift the product with the seat cover and seat open. This may cause mechanical trouble.

The water supply cannot be above 104°F or below 32°F.

Washer

Filter

SMART SEAT BIDET TECHNICAL SPECIFICATIONS

Regulator

cover

Regulate

o-ring

Sealing

o-ring

—7 —

WASH

· Turn the lever clockwise form the vertical position.

· Nozzle for WASH moves forward and will start the function.

· The water volume changes with the turning of the lever.

BIDET

· Turn the lever counterclockwise form the vertical position.

· Nozzle for BIDET moves forward and will start the function.

· The water volume changes with the turning of the lever.

OFF & SELF-CLEANING

· Keep the lever at the 90° position when not in use.

· The wand cleans itself after each use. For additional flush clean of the wands, position the lever at

25° for a few seconds and then reposition back to 90°.

Low flow

High flow

Low flow

High flow

25˚

90˚

SMART SEAT BIDET FUNCTIONS

—8 —

OUTER CLEANING INSTRUCTIONS:

· Use a smooth or cloth with diluted kitchen detergent to clean the product. Do not use the following:

hydrogen chloride detergent, paint thinner, benzene, abrasive paper, polishing agent, fragrance or

insecticide etc.

CLEANING THE NOZZLE:

· Pull out the nozzle gently and use a smooth sponge, cloth or toothbrush with kitchen detergent to

clean the nozzle.

CLEANING THE FILTER & REGULATOR:

If the water flow is less than usual:

1. Clean the filter for both sides. Make sure to disconnect the water supply hose during cleaning.

2. Clean the regulator o-ring.

REMOVAL:

· To remove, close the lid, push the dismantlement button and pull out the product according to the

arrows shown below.

Filter

Braided hoses

Regulator

Dismantlement

SMART SEAT BIDET MAINTENANCE

—9 —

LEVER REPLACEMENT:

· As per figure A, rotate the lever to the highest

wash volume. As per figure B, remove the old lever

along the axis direction.

· As per figure C, insert the new lever rib into the

corresponding control valve slot. The installation is

completed with a *click* sound.

NOZZLE REPLACEMENT:

· As per figure A, pull out the tube and do not

release then remove the old nozzle along the axis

direction. As per figure B, insert the new nozzle into

the tube along the corresponding slot. The nozzle

replacement is completed.

REGULATOR REPLACEMENT:

· Rotate the lever in the working position, remove

the regulator from the inlet tube with pliers.

· Press the new regulator into the bottom of the

inlet tube. The regulator replacement is completed.

· Rotate the lever back to non-working position.

WATER HOSE LEAKING SOLUTION:

· If water leaks from the two ends of water hose,

re-tighten the nuts to avoid water leaking, making a

quarter-turn at a time to avoid damaging the fitting.

ABCAB

nozzle

Regulator

SMART SEAT BIDET MAINTENANCE

Inhaltsverzeichnis

Andere Swiss Madison Toilette Handbücher

Swiss Madison

Swiss Madison Concorde SM-1T106 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT450 Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime II SM-1T257 Bedienungsanleitung

Swiss Madison

Swiss Madison St. Tropez SM-1T253 Bedienungsanleitung

Swiss Madison

Swiss Madison Bastille SM-1T128 Bedienungsanleitung

Swiss Madison

Swiss Madison Hugo SM-ST040 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T803 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WK465-01C Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime II SM-2T257 Bedienungsanleitung

Swiss Madison

Swiss Madison Nadar SM-2T141 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT514 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T113 Bedienungsanleitung

Swiss Madison

Swiss Madison Avallon SM-1T121 Bedienungsanleitung

Swiss Madison

Swiss Madison Plaisir SM-1T119 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T114 Bedienungsanleitung

Swiss Madison

Swiss Madison SM-1T256 Bedienungsanleitung

Swiss Madison

Swiss Madison Virage SM-1T118 Bedienungsanleitung

Swiss Madison

Swiss Madison Calice SM-WT465 Bedienungsanleitung

Swiss Madison

Swiss Madison Calice Bedienungsanleitung

Swiss Madison

Swiss Madison SM-WT514MB Bedienungsanleitung

Swiss Madison

Swiss Madison Avancer Smart Toilet Bedienungsanleitung

Swiss Madison

Swiss Madison Daxton SM-1T125 Bedienungsanleitung

Swiss Madison

Swiss Madison Sublime SM-1T205BQ Bedienungsanleitung

Swiss Madison

Swiss Madison St. Tropez SM-1T254 Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Kohler

Kohler K-6419 Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Kohler

Kohler K-5171K Montageanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Kohler

Kohler K-24097X Montageanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

Kohler

Kohler K-22241K Montageanleitung

Kohler

Kohler ESCALE K-32771T-NS Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung