SY HDBT-662 Bedienungsanleitung

SY Electronics Ltd., 7 Worrall Street, Salford, Greater Manchester, M5 4TH

Tel: +44 (0)161 868 3450 – Fax: +44 (0)161 868 3459

Web: sy.uk

User Manual

HDBT-662

6 Input Dual Zone HDBaseT

Distribution Amplifier

sy.uk 2V1.0

The SY-HDBT-662 is a six input distribution amplifier with dual output zones. Available inputs are

four HDMI inputs, one DisplayPort input and one VGA input. Each of the two output zones provides

a local HDMI output and three HDBaseT outputs, the input source for these zones are independently

selectable from either the front panel buttons, using RS232 commands or the Ethernet port.

Features

Four HDMI inputs, one DisplayPort input and one VGA input

HDMI input 1 supports up to HDCP 2.2

Two output zones each with a local HDMI output and three HDBaseT outputs

Illuminated front panel buttons for each input and output combination

RS232 or Ethernet control

Separate RS232 port for the HDBaseT outputs

IR control to or from the remote location via the HDBaseT outputs

Connectors and Controls

Front

Button Group

Description

ZONE 1

Press the desired button to select that input to the ZONE 1 output group

ZONE 2

Press the desired button to select that input to the ZONE 1 output group

Rear

Connector

Description

48V DC PSU Input

48V DC power supply input

Audio

Audio input for VGA input

VGA

VGA input connector

DisplayPort connector

HDMI 1 – HMDI 4

HDMI Inputs

ZONE 1 – HDMI

Local HDMI output for Zone 1

ZONE 1 – HDBT 1-3

Three remote HDBaseT outputs for Zone 1

ZONE 2 – HDMI

Local HDMI output for Zone 2

ZONE 2 – HDBT 1-3

Three remote HDBaseT outputs for Zone 2

Audio Out – Zone 1

Audio output from the selected input for Zone 1

Audio Out – Zone 2

Audio output from the selected input for Zone 2

Control – RS232

RS232 signals for the HDBaseT ports in both Zones

Control – RS232 CTL

RS232 signals for controlling the HDBT-662

Control – Ethernet

Ethernet port for controlling the HDBT-662

Control – Input Select

Allows selection of any input to either Zone 1 or Zone 2

IR IN – Zone 1

IR input from IR EYE for Zone 1 HDBaseT outputs

IR IN – Zone 2

IR input from IR EYE for Zone 2 HDBaseT outputs

IR OUT – Zone 1

IR output from Zone 1 HDBaseT receivers

IR OUT – Zone 2

IR output from Zone 2 HDBaseT receivers

V1.0 3sy.uk

Connector

Description

SERVICE

For use by Service personnel only

Using the SY-HDBT-662

Up to four HDMI sources, one DisplayPort source and one VGA source may be connected to the

SY-HDBT-662. Each of these inputs can be independently selected to the two output zones. The

output connectors in a single Zone will all show the same input signal, but each output Zone can

show different inputs.

For example, the HDMI and HDBaseT outputs in Zone 1 can all be showing HDMI input 2, while the

HDMI and HDBaseT outputs in Zone 2 are showing HDMI input 4.

The Zone 1 L+R Audio Output will output the audio from the selected input for Zone 1, and the Zone

2 L+R Audio Output will output the audio from the selected input for Zone 2. So, using the above

example, Zone 1 Audio Out will have the de-embedded audio from HDMI input 2, and Zone 2 Audio

Out will have the de-embedded audio from HDMI input 4.

The input selection to each Zone may done using any of the following control methods:

Front Panel buttons

RS232 commands

Ethernet port

I/O Control

RS232 and IR control signals can also be passed between the HDBT-662 and the connected

HDBaseT receivers.

Front Panel LED Indications

The front panel selection LEDs (and those on the external switch box, if fitted) provide feedback on

the input signal status:

A valid input signal is indicated by a solid LED

A no signal state is indicated by a flashing LED

Using an External Switches

The SY-HDBT-662 has an interface for Input selection, using simple external Push Button switches,

as shown in the following schematic:

For each connector, pin 1 is left-most when viewed from the rear of the HDBT-662.

sy.uk 4V1.0

An LED can be used in parallel with each switch, mirroring the input selection status as per front

panel (FP). Any input selection (from FP, external PB switches, RS232) is accordingly reflected

on all FP LEDs, External PB switches/LEDs, and the RS232.

The output that is controlled by the external switch can be set using an RS232 command. The

available settings are: Zone 1 only; Zone 2 only or both Zone 1 and Zone 2 together.

An additional feature provided by this external keypad is that each time the DP and VG buttons

are pressed simultaneously, the controlled output Zone toggles between controlling Zone 1 only,

controlling Zone 2 only, or controlling both Zones together. The controlled output Zone setting is

indicated by all the button LEDs of the Zone lighting up briefly when the VG and DP buttons are

released.

RS232-CTL Commands

All RS232 commands are sent with the following settings:

57600 baud, 8 data bits, no parity and one stop bit.

Commands are not case sensitive, but must always be followed by a carriage-return (0x0d). All

spaces are optional, but are shown in the command tables for clarification.

All response messages are in uppercase and provide an acknowledgement of the command or

reply with the requested data. All responses are terminated with a carriage-return & line-feed

sequence (0x0d 0x0a).

System Settings

Command

Description

Get a list of all available commands

STA

Get a verbose list of all current system settings

GET STA

Get a short list of the current system settings

SET ADDR xx

Set the system address to xx

GET ADDR

Set the system address

SET HIP aaa.bbb.ccc.ddd

Set a new Host IP address

GET HIP

Get the current Host IP address (default: 192.168.1.239)

SET RIP aaa.bbb.ccc.ddd

Set a new router IP address

GET RIP

Get the current Router IP address (default: 192.168.1.239)

SET NMK aaa.bbb.ccc.ddd

Set a new network mask

GET NMK

Get the current network mask (default: 255.255.255.0)

SET TCP nn

Set a new TCP port number

GET TCP

Get the current TCP port number (default: 23)

SET DHCP x

Set the DHCP status, where x is 0 = OFF (Static IP) and 1 = ON

GET DHCP

Get the current DHCP status

Video Settings

Command

Description

SET OUTx VS INy

Set the output x to input y.

Where x is: 0 input y is selected to both output zones

1 for zone outputs, or 2 for Zone 2 outputs

Where y is: 1 – 4 (HDMI 1 – 4), 5, (DisplayPort), or 6 (VGA)

GET OUTx VS

Get the currently selected input for output zone x (1 or 2)

V1.0 5sy.uk

Audio Settings

Command

Description

SET OUTx EXA EN

Enable the external audio for output zone x (1 or 2)

SET OUTx EXA DIS

Disable the external audio for output zone x (1 or 2)

GET OUTx EXA

Get the status of the external audio for output zone x (1 or 2)

EDID Commands

Command

Description

SET INx EDID y

Set the HDMI or DisplayPort input EDID to setting y – see

Default EDID Settings in the table below.

Where x is: 1 – 4 (HDMI 1 – 4) or 5 (DisplayPort)

SET IN6 EDID y

Set the VGA input EDID to setting y – see Default EDID

Settings in the table below

GET INx EDID

Get the index number for the current EDID setting for input x

Where x is: 1 – 4 (HDMI 1 – 4), 5 (DisplayPort), or 6 (VGA)

SET INx EDID CY OUTy

Copy the display EDID from output y to input x

Where x is: 1 – 4 (HDMI 1 – 4), 5 (DisplayPort), or 6 (VGA)

and y is: 1 (Zone 1 output), or 2 (Zone 2 output)

SET INx EDID Uy DATAz

Copy EDID data z to User Memory y for input x.

Please note: to ensure proper operation of the HDBT-662 and

the video source, the EDID values for parameter z must be a

valid EDID data block of either 128 or 256 bytes. (VGA

normally requires 128 bytes, but HDMI and DisplayPort must

have 256 bytes of EDID data).

GET INx EDID y DATA

Get the EDID data for setting y used by input x

Where x is: 1 – 4 (HDMI 1 – 4), or 5 (DisplayPort)

and y is the index value given below in the Default EDID

Settings table

GET IN6 EDID y DATA

Get the EDID data for setting y used by the VGA input

and y is the VGA index value given below in the Default EDID

Settings table

GET OUTx EDID DATA

Get the EDID data for the display device connected to the SY-

HDBT-70SR receiver

Back Panel PB Input Selection

Command

Description

SET BP SEL BUTx

Set rear panel I/O for source switching to HDMI, HDBaseT or Both

GET BP SEL BUT

Get the current rear panel I/O control mode

EDID Settings

Please note that the HDMI, DisplayPort and VGA inputs have the following differences:

Input

HDMI & DisplayPort

VGA

Default EDID Settings

User EDID Memories

sy.uk 6V1.0

Default EDID Settings

The following values are permitted for the y value in the SET INx EDID y and SET INx EDID

y commands.

Y value

IN1 – 4 (HDM1 – HDMI4I) / IN5 (DisplayPort)

IN6 (VGA)

1080P 2Ch audio (PCM)

VGA 1080p

1080P 6Ch audio

USER1 EDID Memory

1080P 8Ch audio

USER2 EDID Memory

1080P 3D 2Ch audio (PCM)

USER3 EDID Memory

1080P 3D 6Ch audio

Not valid

1080P 3D 8Ch audio

Not valid

4K 30Hz 3D 2Ch audio (PCM)

Not valid

4K 30Hz 3D 6Ch audio

Not valid

4K 30Hz 3D 8Ch audio

Not valid

4K 60Hz (Y420) 3D 2Ch audio (PCM)

Not valid

4K 60Hz (Y420) 3D 6Ch audio

Not valid

4K 60Hz (Y420) 3D 8Ch audio

Not valid

1080P 2Ch audio (PCM) HDR

Not valid

1080P 6Ch audio HDR

Not valid

1080P 8Ch audio HDR

Not valid

1080P 3D 2Ch audio (PCM) HDR

Not valid

1080P 3D 6Ch audio HDR

Not valid

1080P 3D 8Ch audio HDR

Not valid

4K 30Hz 3D 2Ch audio (PCM) HDR

Not valid

4K 30Hz 3D 6Ch audio HDR

Not valid

4K 30Hz 3D 8Ch audio HDR

Not valid

4K 60Hz (Y420) 3D 2Ch audio (PCM) HDR

Not valid

4K 60Hz (Y420) 3D 6Ch audio HDR

Not valid

4K 60Hz (Y420) 3D 8Ch audio HDR

Not valid

USER1 EDID memory

Not valid

USER2 EDID Memory

Not valid

USER3 EDID Memory

Not valid

RS232-CTL to Remote HDBT Commands

Command

Description

SET SEPM x EN/DIS

Set data (8bit, no parity, 1 stop) Baud rate, and Enable or Disable

RS232 communications

x is: 0 = 57600 1 = 1200 2 = 2400 3 = 4800 4 =

9600

5 = 14400 6 = 19200 7 = 38400 8 = 56000 9 =

115200

GET SEPM

Get RS232 Enable/Disable state

SET BPSEL HDBTx

Set HDBaseT output x to the RS232_CTL port for RS232 pass

through

Where x is: 1 – 3 for Zone 1 HDBaseT outputs 1 to 3, or

4 – 6 for Zone 2 HDBaseT outputs 1 to 3

GET BPSEL HDBT

Get the current HDBaseT output that is set for RS232 pass-

through

V1.0 7sy.uk

IR Code Setup

RS232 Command

Command Details

SET IR SYS xx yy

Set IR System Code

Where xx and yy define a 16-bit address, each in the range

[00-FF] (Factory default is 00 FF)

SET IR OUTx INy CODE

Set selection IR Data Code {x[1~2], y[1~6], zz[00~FF]}

Define the IR data code to select the inputs and outputs:

Output x is: 1 = Zone 1 output, or 2 = Zone 2 output

Input y is: 1 - 4 = HDMI inputs 1 to 4

5 = DisplayPort input

6 = VGA input

Data value zz is a unique value for the specified input and

output combination.

Default IR values are: Local Remote

HDMI 1 Input 0x80 0x90

HDMI 2 Input 0x82 0x92

HDMI 3 Input 0x84 0x94

HDMI 4 Input 0x86 0x96

DisplayPort Input 0x88 0x98

VGA Input 0x8a 0x9a

GET IR SYS

Get the current IR System Address Code

GET IR OUTx INy CODE

Get IR Data Code for {x[0~2], y[1~6]}

x[0~2] 0 = Both outputs, 1 = Zone 1 output, 2 = Zone 2

output

y[1~6] 1 - 4 = inputs HDMI 1 to 4, 5 = DP, 6 = VGA

SET IR ALL EN/DIS

Use Enable mode to set Zone 1 IR IN to output to both Zone 1

and Zone 2

Use Disable to set Zone 1 IR IN to output only to Zone 1

Using the Web Interface

The SY-HDBT-662 also has a built-in web interface that can also be used to control the

unit for input selections, EDID settings and network management. The default IP settings

are:

Host IP: 192.168.1.239

Gateway: 192.168.1.1

Network mask: 255.255.255.0

TCP Port: 23

DHCP: Off

These settings can also be used to send the RS232 commands over a LAN connection

with the sender set up as a TCP Client.

sy.uk 8V1.0

RJ45 Wiring

Both connectors must be wired identically.

HDBT will not pass through any Ethernet device, the HDBT port on the SY-MFT21 must be

connected directly to the HDBT port on the SY-HDBT-70SR.

Please do make sure that the Cat6 cable uses 4 pairs of 23AWG solid copper wires. Do not use

inferior copper clad cables as these exhibit high resistances.

Specifications

Items

Description

HDMI / DisplayPort Video

Input/output

VESA and SMPTE 480p to 2160p (4K UHD) with 3D. (All resolutions to:

4096x2160p @60Hz 4:2:0 8bit, 3840x2160p @30Hz 4:4:4 8bit)

All PC resolutions to 1920x1200

VGA Video Input

The following VGA resolutions are supported:

800x600, 1024x768, 1280x768, 1280x800, 1280x1024, 1400x1050,

1600x1200, 1920x1080 and 1920x1200.

HDMI Audio

Input/output

Pass through: All HDMI audio formats including Dolby D (TrueHD) / DTS

(HD-Master Audio) / PCM.

Channel count: from 2-8 (2.0 to 7.1)

Sample rates: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and

192 kHz

De-embedded Audio out

PCM 2.0 channel from HDBT output, onto 3 pin Phoenix connector.

Stereo L/R, 0.7V Rms – 20Hz-20KHz

Power Supply

48V DC @ 2.0A max.

Power Consumption

17.3W with one receiver (add 6.5W per additional receiver)

50W max. (all HDBaseT outputs in use)

HDBaseT Outputs

Max 70m (230feet) of cat6a, @ 1080p. HDMI video, RS232, IR control, PoC

PoC is available only when SY-HDBT-SLIM-70SR is detected on the HDBT

output.

Control

RS232 & IR Full function bi-directional pass-though

RS232-CTL port – 57,600 Baud, no Parity, 1 Stop bit

Dimensions

438 x 225 x 44mm (19in x 1U rack mounting)

Case Material

Steel chassis

Weight

3 kg

V1.0 9sy.uk

Safety Instructions

To ensure reliable operation of these products as well as protecting the safety of any person using

or handling these devices while powered, please observe the following instructions.

1. Use the power supplies provided. If an alternate supply is required, check Voltage,

polarity and that it has sufficient power to supply the device it is connected to.

2. Do not operate either of these products outside the specified temperature and humidity

range given in the above specifications.

3. Ensure there is adequate ventilation, as these products generate heat while operating.

4. Repair of the equipment should only be carried out by qualified professionals as these

products contain sensitive devices that may be damaged by any mistreatment.

5. Only use these products in a dry environment. Do not allow any liquids or harmful

chemicals to come into contact with these products.

After Sales Service

1. Should you experience any problems while using these products, firstly refer to the

Troubleshooting section in this manual before contacting SY Technical Support.

2. When calling SY Technical Support, the following information should be provided:

Product name and model number

Product serial number

Details of the fault and any conditions under which the fault occurs.

3. These products have a two year standard warranty, beginning from the date of purchase

as stated on the sales invoice. Online registration of these products is required to activate

the full three year extended warranty. For full details please refer to our Terms and

Conditions.

4. SY Product warranty is automatically void under any of the following conditions:

The product is already outside of its warranty period

Damage to the product due to incorrect usage or storage

Damage caused by unauthorised repairs

Damage caused by mistreatment of the product

5. Please direct any questions or problems you may have to your local dealer before

contacting SY Electronics.

sy.uk 10 V1.0

NOTES

Inhaltsverzeichnis

Andere SY Verstärker Handbücher

SY 2A-20W Bedienungsanleitung

SY SY-2A-20W Bedienungsanleitung

SY SY-1A-25R Bedienungsanleitung

SY SY-3A-40W Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung