Symantec CAS-S200 Bedienungsanleitung

24 Aug 2021

Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, the A logo, Symantec, the Symantec logo, the Checkmark logo, Blue Coat, and the Blue Coat

The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com.

Figure 1: CAS-S200, CAS-S400, CAS-S500 Deployments

Content Analysis Quick Start Guide

CAS-S200, CAS-S400, CAS-S500 Appliances

CAS-S200, CAS-S400, CAS-S500

Content Analysis

Quick Start Guide

1 — Unpack the Appliance

Unpack the shipping package for the appliance and verify it

includes the following:

2 — Connect Cables

It is recommended that you plug in cables, verify LEDs, and

configure and license the appliance before mounting it in an

equipment rack. Make sure the appliance is on a flat, level

surface when performing the initial configuration. If you would

rather mount the appliance before performing configuration

tasks, skip to Mount the Appliance.

The following procedure describes a typical deployment for

CAS-

S200,

CAS-

S400, and

CAS-

S500 appliances (as shown

in Figure 1). For information on other deployments, see the

Content Analysis

software documentation, available at:

techdocs.broadcom.com

NOTE: Network cables are not included with the appliance.

Make sure to use only straight-through Ethernet cables.

Category 5E cables or better are recommended for

1000Base-T operation. Category 6A cables are

recommended for 10GBase-T operation.

To deploy the appliance and connect cables:

1. Deploy the ProxySG appliance:

Disconnect the Ethernet cable (if there is one) between

the LAN switch and WAN router.

Connect the ProxySG appliance to the LAN switch:

– For SG-S200 and SG-S400 appliances, connect an

Ethernet cable to the appliance’s LAN 2:0 port and

connect the other end of the cable to the LAN switch.

– For SG-S500 appliances, connect an Ethernet cable

to the appliance’s LAN 1:0 port and connect the

other end of the cable to the LAN switch.

Connect the ProxySG appliance to the WAN router:

– For SG-S200 and SG-S400 appliances, connect an

Ethernet cable to the appliance’s LAN 2:1 port and

connect the other end of the cable to the WAN router.

– For SG-S500 appliances, connect an Ethernet cable to

the appliance’s LAN 1:1 port and connect the other end

of the cable to the WAN router.

For more information on ProxySG deployment, see the

ProxySG Quick Start Guide.

2. Deploy the Content Analysis appliance:

Connect an Ethernet cable to the Content Analysis

appliance’s LAN 1:0 port and connect the other end of

the cable to the ProxySG appliance. The appliances

auto-negotiate 10/100/1000 Base-T speed and duplex

settings.

Connect an Ethernet cable to the Content Analysis

appliance’s MGMT 0:0 port and connect the other end

of the cable to the management network router.

3. Connect the included null-modem cable to the Content

Analysis appliance’s DB9 Serial port and connect the

other end of the cable to a serial terminal or workstation

with terminal emulation software. The serial connection

is used to perform the appliance’s initial configuration.

4. For CAS-S500 appliances, attach the lug-equipped end

of the included grounding wire (10 AWG) to both ground-

ing studs on the appliance, securing it with the star

washers and M5 nuts. Attach the other end of the

grounding wire to a proper earth-ground.

5. Connect the Content Analysis appliance to a power

source:

For CAS-S200 appliances, connect the included power

supply cord to the appliance’s power inlet and connect

the other end of the power cord to a power source.

Appliance CAS-S200 CAS-S400 CAS-S500

AC power cords

(number included)

122

Null-modem serial cable √ √

Grounding hardware √

2- and 4-post slide-rail kit optional √ √

2-post fixed rail √

Accessing Appliance

Documentation

√√√

Software License Agreement

√√√

Hardware Warranty

Information

√√√

CAS-S200, CAS-S400, CAS-S500

Content Analysis

Quick Start Guide

For CAS-S400 and CAS-S500 appliances, connect the

included power cords to the appliance’s power inlets

and connect the other ends of the power cords to a

power source.

3 — Power On the Appliance and

Verify LEDs

To verify the appliance is operational:

1. Confirm the appliance’s power cords are securely

connected to a power source.

2. If the appliance does not automatically power on, press

the rear soft power switch.

NOTE: The state of the appliance’s soft power switch (on

or off) is retained when power is removed. This may ne-

cessitate pressing the power switch when reapplying

power to the appliance.

3. As the appliance boots, verify the following:

The power LED turns amber.

Near the end of the boot cycle, the Power LED alter-

nates between amber and green, indicating an uncon-

figured state.

After the boot cycle has completed, the LCD panel dis-

plays information about the appliance, such as model,

serial number, and IP address, which can be scrolled

through with the Right and Left Arrows.

Following the initial configuration and licensing, the

Power LED turns green.

During operation, the front-panel status LEDs indicate the

following states:

4 — Perform the Initial Configuration

NOTE: To initialize the appliance, you need the following:

appliance IP address; primary DNS server IP address;

default gateway IP address; subnet mask

, admin password

for access to the appliance.

To perform the initial configuration for the appliance:

1. Confirm the appliance’s DB9 Serial port is connected to

a serial terminal or workstation with terminal emulation

software.

2. Open a terminal emulation program, such as Microsoft

HyperTerminal®, PuTTY, Tera Term, or ProComm™,

and configure it to use the following settings:

3. Power on the appliance (if it is not already powered on)

and, when prompted, press Enter three times.

4. When prompted, enter network configuration parame-

ters. If the appliance is connected to a network, the Con-

figuration Wizard attempts to verify the DNS server

address and auto-detect link settings.

5. When prompted, assign a Username and Password to

the admin account.

5 — License the Appliance

The Content Analysis appliance requires a base license for

its primary components. Add-on licenses provide access to

optional components, such as Antivirus, Sandboxing, Pre-

dictive Analysis, and Hash Reputation. When you purchase

the appliance, you will receive an e-fulfillment letter contain-

ing your appliance’s serial number and activation code for

subscription services.

To license the appliance:

1. Register the appliance:

Go to support.broadcom.com/security and click My

Entitlements. When prompted, enter the admin User-

name and Password, then click Sign In.

Search for the appliance you want to register by enter-

ing its Serial Number, Site ID, or Email.

LED Color Description

Power

Status

Off Powered off or no power present

Amber Booting

Amber/green

alternating

Not yet initialized

Green Powered on and configured

System

Status

Off Powered off or no power present

Green Normal

Amber System fault or not yet licensed

Amber blinking Critical fault

Baud rate: 9600 bps Data bits: 8

Parity: none Stop bits: 1

Flow control: none

CAS-S200, CAS-S400, CAS-S500

Content Analysis

Quick Start Guide

Follow the on-screen prompts to register the appliance

and activate the base license.

2. Download and install the base license:

Open a browser and enter the appliance’s IP address

and port number. For example, an IP address of

192.168.2.42 with a port number of 8082 (the default)

would be: https://192.168.2.42:8082.



When prompted, enter the admin Username and Pass-

word specified during the initial configuration, then click

In the Management Console window, choose System >

Licensing.



Click Download License from Symantec. The appliance

automatically downloads and installs the base license.

3. View and activate license components:

In the Management Console window, choose System >

Licensing. The Licensing Activation section displays

the available license components, their status, and

whether they are active.

To activate a license component, click in the Active col-

umn to enable its checkbox.

Click Save Changes.

6 — Perform a Graceful Shutdown

Before mounting the appliance, log in to CLI and perform a

graceful shutdown of the appliance.

To perform a graceful shutdown:

1. Open a terminal emulation program and log in to the

appliance.

NOTE: Confirm the appliance’s DB9 Serial port is con-

nected to a serial terminal or workstation and that the ter-

minal emulation software is configured as in Perform the

Initial Configuration.

2. When prompted with the Serial Console welcome

screen, to access CLI, press: 1

3. To access privileged commands, enter: enable

4. When prompted, enter the enable Password specified

during the initial configuration.

5. Enter: shutdown

WARNING!

Do not power off the appliance with the soft pow-

er switch or by removing the power cables! Abruptly removing

power can result in irreparable data loss. Always use the

shutdown command from CLI to power off the appliance.

7 — Mount the Appliance

The slide-rail kit included with

CAS-S400

and

CAS-S500

ap-

pliances (available as an option for

CAS-S200

appliances)

allows the appliance to be mounted in a 4- or 2-post equip-

ment rack. The slide-rail kit includes the following parts:

NOTE: Installation of the slide rails requires an M4 nut driver

or adjustable wrench and a #2 Phillips head screwdriver. If

you are working alone, a mechanical lift is also required.

NOTE: The following procedure documents installation for 4-

post equipment racks (as shown in Figure 2). For 2-post instal-

lation, see the S-Series WebGuide, available at:

techdocs.broadcom.com/sseries

Item

(2) Front brackets

(2) Inner rails

(2) Rear brackets

(2) Center brackets

(2) Rack ears

(8) M6x13 screws

(8) M6 cage nuts

(10) M4x4L screws

(4) M3L4 screws

CAS-S200 (Optional) and CAS-S400 Rail Kit

Item

(2) Front brackets

(2) Inner rails

(2) Rear brackets

(4) Middle brackets

(8) M6x13 screws

(8) M6 cage nuts

(10) M4x5L screws

(4) M4x4L screws

CAS-S500 Rail Kit

CAS-S200, CAS-S400, CAS-S500

Content Analysis

Quick Start Guide

Rack Warnings and Precautions

CAUTION! Before mounting the appliance:

Power off the appliance (see Perform a Graceful

Shutdown) and disconnect all cables.

Verify that the weight of the system does not exceed the

rack’s fully populated weight limit. For more information,

refer to the manufacturer’s instructions included with

the rack.

For weight stability, load the rack from the bottom up.

Read the “Rack Mount Warnings” section of the Safety

and Compliance Guide.

Take adequate safety and grounding measures to avoid

creating an electrical shock hazard and to prevent

bodily injury.

The appliance is heavy. A two-person lift or mechanical

aid is recommended to lift the appliance from the carton

and install it in the rack.

Do not place objects on the appliance or use it as a

work surface. Its mounting hardware does not support

additional weight.

Install the Appliance into the Rack

To install the appliance into a 4-post equipment rack:

1. Disassemble the two slide-rail assemblies. Extend the

inner rails while pressing the center release tabs, then

fully remove them (a).

2. Attach the two inner rails to the chassis sides, aligning

the rails with the mounting posts on the chassis, then

slide the rails forward (CAS-S200, CAS-S400) or rear-

ward (CAS-S500) until they snap into place. Secure

each rail with one (CAS-S200, CAS-S400) or two

(CAS-S500) M4x4L screws (b).

3. For CAS-S200 and CAS-S400 appliances, attach the

two rack ears to the chassis, aligning them with the

raised screw holes and orienting them with the captive

screw heads toward the front of the appliance. Secure

each rack ear with two M3L4 screws.

4. Install the two outer rails into the 4-post equipment rack (

Secure the rear brackets to the front brackets with six

M4x4L (CAS-S200, CAS-S400) or M4x5L (CAS-S500)

screws, three per side, placed equidistantly. Do not yet

fully tighten the side-mounting screws.

Figure 2: CAS-S500 Slide-Rail Installation

CAS-S200, CAS-S400, CAS-S500

Content Analysis

Quick Start Guide

Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume

any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. (2021.08.24, 13:04:19)

Attach the two outer rails to the rack, extending the rails

as necessary to fit the rack. Secure the front and rear

brackets with two M6 rack screws each. Do not yet fully

tighten the rack screws.

Fully tighten the side-mounting screws, three per side,

securing the rear brackets to the front brackets.

Inspect the outer rails, making sure they are installed at

the same level in the rack and free of defects, damage,

and debris. Verify the rails extend and retract smoothly

and stop at the slide-stop.

5. Install the chassis into the 4-post equipment rack (d):

Align the inner rails attached to the appliance with the

outer rails in the rack and slide the appliance half-way

into the rack.

Fully tighten the M6 rack screws securing the outer rails

to the rack.

Press the release tabs on the inner rails and gently

slide the appliance all the way into the rack.



Tighten the captive thumbscrews on the appliance’s rack

ears to prevent the appliance from sliding out of the rack.

6. Reconnect the cables as documented in Connect Cables

and verify the appliance is functioning as in Power On the

Appliance and Verify LEDs.

See below for support and additional documentation.

Symantec Technical Support

For Symantec technical support, case management,

licenses, and product downloads, go to:

support.broadcom.com/security

Content Analysis Software Documentation

Go to techdocs.broadcom.com and type “content” in

the search field, then click Content Analysis.

Appliance Documentation

S Series WebGuide (Maintenance and Upgrades)

techdocs.broadcom.com/sseries

S200 Series Safety and Compliance Guide

techdocs.broadcom.com/s200

S400 Series Safety and Compliance Guide

techdocs.broadcom.com/s400

S500 Series Safety and Compliance Guide

techdocs.broadcom.com/s500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Symantec Netzwerk-Hardware Handbücher

Symantec

Symantec NetBackup 5200 Series Technische Daten

Symantec

Symantec NetBackup 5200 Series Bedienungsanleitung

Symantec

Symantec S450 Series Installations- und Betriebsanleitung

Symantec

Symantec SG-S200 Bedienungsanleitung

Symantec

Symantec RP-S500 Bedienungsanleitung

Symantec

Symantec SSL Visibility SV800 Bedienungsanleitung

Symantec

Symantec PacketShaper PS-S200 Bedienungsanleitung

Symantec

Symantec S550 Series Installations- und Betriebsanleitung

Symantec

Symantec S200 Series Installations- und Betriebsanleitung

Symantec

Symantec Shelf NetBackup 5220 Installations- und Betriebsanleitung

Symantec

Symantec NetBackup 5020 Gebrauchsanweisung

Symantec

Symantec SIEM 9700 Series Handbuch

Symantec

Symantec SIEM 9700 Series Bedienungsanleitung

Symantec

Symantec Shelf NetBackup 5220 Betriebsanleitung

Symantec

Symantec EDR S550 Bedienungsanleitung

Symantec

Symantec SV1800 Series Installations- und Betriebsanleitung

Symantec

Symantec S450 Series Installations- und Betriebsanleitung

Symantec

Symantec NetBackup 5000 Gebrauchsanweisung

Symantec

Symantec CAS S200 Bedienungsanleitung

Symantec

Symantec SV2800 Installations- und Betriebsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung