Symmetry EN-7510 Bedienungsanleitung
Symmetry EN-7510
Installation Guide
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of un-insulated
“dangerous voltage” within the product‟s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
!
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 3 of 23
Table of Contents
1. FEATURES........................................................................................................ 4
2. PACKAGE CONTENTS.................................................................................... 5
3. PART NAMES.................................................................................................... 6
3.1. Rear View......................................................................................................................... 6
3.2. Bottom View..................................................................................................................... 6
4. INSTALLATION................................................................................................. 9
4.1. Installing a C/CS Mounting lens................................................................................... 9
4.2. Installing an Auto IRIS lens........................................................................................... 9
4.3. Setting the Image Attribute.......................................................................................... 10
4.4. Operating the OSD Menu............................................................................................ 10
5. CONNECTIONS............................................................................................... 11
5.1.Connectors...................................................................................................................... 12
6. CONFIGURATION........................................................................................... 15
6.1.Set up network environment ........................................................................................ 15
6.2. View video on web page.............................................................................................. 15
6.2.1. View video using IPAdmin Tool........................................................................... 15
6.2.2. View video using IP address................................................................................ 18
6.3. Reset............................................................................................................................... 18
6.4. Factory Default.............................................................................................................. 18
APPENDIX A: SPECIFICATIONS ...................................................................... 19
Summary................................................................................................................................ 19
Electrical Characteristics..................................................................................................... 20
Environmental Condition..................................................................................................... 20
Analytics................................................................................................................................. 21
APPENDIX B: POWER OVER ETHERNET....................................................... 22
PoE compatibility.................................................................................................................. 22
Power classification.............................................................................................................. 22
APPENDIX C: DIMENSIONS.............................................................................. 23
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 4 of 23
1. FEATURES
Camera
Box type IP Camera
Sony 1/3” Super HAD CCD & High Quality SS-HQ1 Full Kit Chip Set
True Day / Night (ICR) and WDR (Optional)
Streaming
Dual streaming mode (with different codec/resolution/bit rate etc.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MPEG/MJPEG, 25/30FPS@D1(PAL/NTSC)
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video out for external monitors
Video Motion Detection supported
2-way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
RS-485 supported
USB 2.0 supported for external storage
Micro SD card supported
PoE supported
Built-in Video Content Analytics
OSD supported
Analytics
Intelligent Detection (Included as basic)
VCA (Optional)
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 5 of 23
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
DC power adaptor
Mount ring
9 Pin terminal block
Rubber cap (for protecting CCD)
Hex wrench driver
Adaptor for mounting the camera
Screws
Quick Installation Guide
DC Jack Adaptor Cable
Note
i
The above contents are subject to change without prior notice.
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 6 of 23
3. PART NAMES
3.1. Rear View
3.2. Bottom View
○6
○5
○3
①
○1
○2
○4
①
○8
○7
ETHERNET
Micro SD
RESET
LOOP OUT
RS-485
DO
DI
AUDIO
-
+
C
1
C
1
Out
In
○9
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 7 of 23
1. Analog video out
Analog video output port (PAL or NTSC as appropriate).
2. Reset
Reset switch is used for restarting or resetting the camera to Factory Default (FD).
Refer to the section “6.3. Reset”for more specific information.
3. USB connector
Insert a USB storage device.
4. 9 pin terminal block for D/I, D/O, audio, and serial communication
Refer to the section “5.1.Connectors”for more specific information.
5. Power Adaptor Connector (DC 12V)
The camera needs a DC12V for power supply. Refer to the section “Power Adaptor
Connector (DC 12V)”for more specific information.
Caution
!
Make sure the polarity is correct. Incorrect connection may cause
malfunction or damage to the IP device.
6. Micro SD Card socket
Memory card slot for external storage.
7. LAN Connector (Ethernet)
RJ45 LAN connector for 10/100 Base-T Ethernet.
8. 4 Pin connector for Auto IRIS
Only DC-drive type is supported. Refer to the section “4.2. Installing an Auto IRIS
lens”for more specific information.
+
-
Status LED Network LED
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 8 of 23
9. Adaptor for mounting the camera
Mounting points adaptor is provided on the bottom (or the top) of the camera for
mounting the camera on a bracket or tripod.
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 9 of 23
4. INSTALLATION
4.1. Installing a C/CS Mounting lens
1. Remove the protective rubber cap from the front of the camera.
2. Install the mount ring for lens and adjust the mount ring to fit C or CS lens.
3. Tighten the set screws using the hex wrench supplied with the camera.
4.2. Installing an Auto IRIS lens
1. Remove the cover of the auto iris lens plug and connect it with the lens cable.
2. Connect the auto iris lens plug to the 4-pin lens terminal on the back of the camera.
Note
i
Use the connection recommended by the manufacturer. For best
performance, read the lens manual carefully. You may need to set the
flange back focus.
Note
i
Only DC-drive type is supported.
CW
SET SCREW
Set Screw
(For IRIS LENS)
CCW
CW
Symmetry EN-7500 Series EN-7510 Installation Guide
9600-0541 Issue 1.1 Page 10 of 23
4 pin connector for IRIS
PIN
DC IRIS Lens
1
Damp-
2
Damp+
3
Drive+_
4
Drive-
4.3. Setting the Image Attribute
You can set the image attribute of camera through the webpage.
The menu of image attribute can be seen under Setup > Video & Audio > Video-in >
Attribute Setting. Brightness, contrast, hue, saturation and sharpness can be adjusted.
4.4. Operating the OSD Menu
To operate the OSD of camera, refer to the „EN-7510 OSD Menu Control Manual‟ on
the CD supplied with your camera.
2
1
4
3
Inhaltsverzeichnis
