Synology DiskStation DS3615xs Bedienungsanleitung
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology DiskStation at a Glance 4
Safety Instructions 5
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation 6
Install Drives 6
Start Up Your DiskStation 9
Add a RAM Module on DiskStation 10
Add a Network Interface Card on DiskStation 14
Replace System Fan 16
Chapter 3: Install DSM on DiskStation
Install DSM with Web Assistant 17
Learn More 17
Appedix A: Specications
Appedix B: LED Indicator Table
Synology_QIG_DS3615xs_20141127
2
Thank you for purchasing this Synology product! Before setting up your new DiskStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your DiskStation.
Package Contents
Main unit x 1 AC power cord x 1
RJ-45 LAN cable x 2
Screws for 2.5” hard drives x 52
Hard drive tray key x 2
Before You Start 1
Chapter
3
3
4Chapter 1: Before You Start
Synology DiskStation at a Glance
No. Article Name Location Description
1Status Indicator
Front Panel
Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table".
2Alert Indicator Displays warnings regarding fan or temperature. For more information, see
"Appendix B: LED Indicator Table".
3Power Button
1. Press to power on the DiskStation.
2. To power off the DiskStation, press and hold until you hear a beep sound
and the Power LED starts blinking.
4LAN Indicator Displays the status of the network connection. For more information, see
"Appendix B: LED Indicator Table".
5Drive Status Indicator Displays the status of the installed drive. For more information, see "Appendix
B: LED Indicator Table".
6Drive Tray Install drives (hard disk drives or solid state drives) here.
7Drive Tray Lock Lock or unlock drive trays.
8Power Port
Back Panel
Connect the AC power cord here.
9Fan Disposes of excess heat and cools the system. If the fan malfunctions, the
DiskStation will emit a beeping sound.
10 PCI Express
Expansion Slot Supports a PCIe x8 network interface card.
11 USB 3.0 Port Connect external hard drives, USB printers, or other USB devices to the
DiskStation here.
12 Expansion Port Connect Synology Expansion Unit1to the DiskStation here.
13 Console Port This port is used for manufacturing use only.
14 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold again
until you hear three beep sounds to return the DiskStation to “Not Installed”
status so that DiskStation Manager (DSM) can be reinstalled.
15 LAN Port Connect network cables here.
1For more information about Synology Expansion Unit supported by your DiskStation, please visit www.synology.com.
5Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.
Tools and Parts for Drive Installation
• A screwdriver (only for 2.5” drives)
• At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1 Press the right part of the hard drive tray to pop out the handle.
2 Pull the hard drive tray handle in the direction as indicated below to remove the hard drive tray.
Hardware Setup
6
2
Chapter
7Chapter 2: Hardware Setup
3 Load drives in the drive trays.
• For 3.5” drives: Remove the fastening panels from the sides of the drive tray. Place the drive in the drive
tray. Then insert the fastening panels to secure the drive in place.
• For 2.5” drives: Remove the fastening panels from the sides of the drive tray and store them in a safe
place. Place the drive in the blue area (shown below) of the drive tray. Turn the tray upside down and tighten
the screws to secure the drive in place.
4 Insert the loaded hard drive tray into the empty hard drive bay.
Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not be able to function properly.
5 Pressthehandleinushwiththefrontpaneltoholdtheharddrivetrayinplace.
8Chapter 2: Hardware Setup
6 Insert the hard drive tray key into the hard drive tray lock, turn the key clockwise (to the “-” position) to lock the
handle of the hard drive tray, and then remove the key.
7 Repeat the steps above to assemble the other drives you have prepared.
8 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommended that all installed drives are of the same size to make the
best use of drive capacity.
9Chapter 2: Hardware Setup
Start Up Your DiskStation
1 Use the LAN cable to connect the DiskStation to your switch, router or hub.
2 Connect one end of the AC power cord to the power port of the DiskStation, and the other to the power outlet.
3 Press the power button.
Congratulations! Your DiskStation is now online and detectable from a network computer.
10 Chapter 2: Hardware Setup
Add a RAM Module on DiskStation
The optional Synology DDR3 RAM module is designed for DiskStation memory expansion. Follow the steps
below to install, check, or remove a RAM module on your DiskStation.
To install the RAM module:
1 Shut down your DiskStation. Disconnect all cables connected to your DiskStation to prevent any possible
damage.
2 Remove the inner panel:
a Remove the 4 screws on the back of DiskStation, and then pull the top and side cover. Place both covers to
the side.
b Remove the 7 screws that secure the inner panel.
Note: When you remove the case, you expose sensitive internal components. Avoid touching anything other than the
memory assembly when you remove or add memory.
Inhaltsverzeichnis
Andere Synology Lagerung Handbücher
Synology
Synology DiskStation DS414 Bedienungsanleitung
Synology
Synology DiskStation DS209 Bedienungsanleitung
Synology
Synology DiskStation DS112j Bedienungsanleitung
Synology
Synology DiskStation DS920+ Handbuch
Synology
Synology SA3610 Bedienungsanleitung
Synology
Synology DX513 Bedienungsanleitung
Synology
Synology DS1823XS+ Bedienungsanleitung
Synology
Synology DiskStation DS213+ Bedienungsanleitung
Synology
Synology DiskStation DS214se Bedienungsanleitung
Synology
Synology RS2423+ Bedienungsanleitung
Synology
Synology DS720+ Handbuch
Synology
Synology DiskStation DS414j Bedienungsanleitung
Synology
Synology DS1813+ Bedienungsanleitung
Synology
Synology DiskStation DS410j Bedienungsanleitung
Synology
Synology DiskStation DS118 Handbuch
Synology
Synology DS418play Handbuch
Synology
Synology DS423+ Bedienungsanleitung
Synology
Synology DiskStation Series Bedienungsanleitung
Synology
Synology DiskStation DS218j Handbuch
Synology
Synology DS1621xs+ Handbuch
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung