Syslogic C Series Bedienerhandbuch

user documentation

DOC_C-Series_Touch-PC_V1.1.docx Page 1 of 37

TFT/HB101PU81xxx-C001y

Document Ordercode: DOC/C-Series_Touch-PC

Revision

Date

Author

Modification

0.1

16.11.2018

D. Lagler

Preliminary version

0.2

21.11.2018

D. Lagler

Spelling corrections

0.3

06.03.2019

D. Lagler

Added maintenance part and operating conditions

1.0

08.04.2019

D. Lagler

Added pinout of mPCIe and m.2, defined use cases

1.1

07.06.2019

D. Lagler

Mounting instructions and power consumption revised

C-Series Touch-PC: user documentation 
DOC/ C-Series_Touch-PC; V1.1 
DOC_C-Series_Touch-PC_V1.1.docx Seite 2 von 37 
© 2018 Syslogic Datentechnik AG | All rights reserved 
Contents 
1Introduction 5 
1 General Remarks 5 
2 Explanation of Symbols 5 
2.1 Danger warnings 5 
2.2 Warnings indicate the following: 5 
2.3 Information pictograms indicate the following: 6 
3 Copyright note 6 
4 Contents of this Documentation 6 
5 Additional Products and Documents 6 
5.1 Hardware Products 6 
5.2 Software Products 6 
5.3 Documents 6 
6 Items delivered 7 
1.1. Built-in version 7 
1.2. To be purchased separately 7 
7 Installation 7 
8 Safety Recommendations and Warnings 7 
8.1 General warnings 7 
8.2 EMC 7 
8.3 Electro Static Discharge 8 
8.4 Battery 8 
8.5 Hot surface 8 
9 Life Cycle Information 8 
9.1 Transportation and Storage 8 
9.2 Assembly and Installation 8 
9.3 Operation 8 
9.4 Maintenance and Repair 8 
9.5 Disposal 9 
9.6 RoHS 9 
9.7 WEEE 9 
2Product Description 10 
1 Introduction 10 
1.1 Benefits of Syslogic`s Projected capacitive touch panels 10 
1.2 Intended use of Projected Capacitive Touch Panels 10 
2 Device Variants 10 
Standard temperature 10 
Extended temperature 10 
3 Accessories 11 
4 Features 11 
4.1 TFT/HB101PU81xxx-C001y 11 
4.2 Power supply 12 
4.3 X1 (only on selected products) 12 
4.4 X2 (for future use; only on selected produtcts) 13 
4.5 USB Interface 13 
4.6 Ethernet LAN Interface 13 
4.7 Display 13 
4.8 Frontside Status LEDs 14 
4.9 Antennas (only on selected products) 14 

C-Series Touch-PC: user documentation 
DOC/ C-Series_Touch-PC; V1.1 
DOC_C-Series_Touch-PC_V1.1.docx Seite 3 von 37 
© 2018 Syslogic Datentechnik AG | All rights reserved 
4.10 Internal connectors 14 
SO-DIMM 14 
CMOS Battery 14 
Fuse 14 
USB 2.0 14 
m.2 slot 15 
mPCIE slot 16 
5 Touch Screen 16 
5.1 Basic functions of the touch screen 16 
6 Display brightness 16 
7 Maintenance 17 
7.1 Opening the device 17 
7.2 Re-assemble the device 18 
7.3 Internal overview 18 
7.4 Replace m.2 flash memory 19 
7.5 Mount/replace mPCIe module 19 
7.6 Replace CMOS battery 20 
7.7 Replace fuse 20 
7.8 Replace SODIMM 20 
7.9 Re-assemble the device (backplate) 22 
7.10 Replace gap pad 22 
7.11 Cleaning the glass front 22 
7.12 Cleaning the metal housing 22 
7.13 Spare parts 23 
3Installation Description 24 
1 Mounting 24 
1.1 TFT/HB101PU81xxx-C001y 24 
2 Installation and cabling 26 
2.1 Introduction 26 
2.2 Powering the C-Series Touch-PC System 26 
2.3 Cabling the interfaces 26 
2.4 Grounding 27 
2.5 Cabling of communication links 28 
4Technical Data 30 
1 General Electrical Data 30 
2 EMI / EMC Specification 31 
3 Mechanical Data 32 
3.1 TFT/HB101PU81xxx-C001y 32 
4 Use cases 33 
5Firmware 34 
1 Software Structure 34 
2 Firmware Functions 34 
3 Application Programming Interface (API) 34 
4 Supported Operating System 34 
 

C-Series Touch-PC: user documentation 
DOC/ C-Series_Touch-PC; V1.1 
DOC_C-Series_Touch-PC_V1.1.docx Seite 4 von 37 
© 2018 Syslogic Datentechnik AG | All rights reserved 
6Product Revision History 35 
6.1 Hardware 35 
6.2 Firmware 35 
6.3 Errata 36 
7Manufacturer Information 37 
7.1 Contact 37 
7.2 Warranty 37 
7.3 RMA Service 37 
List of Tables 
Tab. 1 Projected capacitive touch panel versions 10 
Tab. 2 Projected capacitive touch panel accessories 11 
Tab. 3 Power supply connector (1x3 pin) 12 
Tab. 4 Serial Port X1 12 
Tab. 5 Frontside Status LEDs 14 
Tab. 6 Pinout internal USB ports 14 
Tab. 7 Pinout m.2 15 
Tab. 8 Pinout mPCIe 16 
Tab. 9 TFT/HB101PU81xxx-C001y Mounting dimensions 24 
Tab. 10 General Absolute Maximum Ratings 30 
Tab. 11 General Recommended Operating Conditions 30 
Tab. 12 Maximum cable length 30 
Tab. 13 General Electrical Characteristics 31 
Tab. 14 General Switching Characteristics 31 
Tab. 15 Hardware Revision State 35 
Tab. 16 Firmware Revision State 35 
List of Figures 
Fig. 1 TFT/HB101PU81xxx-C001y (Front) 11 
Fig. 2 TFT/HB101PU81xxx-C001y (Back) 11 
Fig. 3 Required Cut out HBxxxPU8yyy-zZZZ 24 
Fig. 4 Screws to hold the mounting Frame 25 
Fig. 5 Fully installed C-Series Touch-PC 25 
Fig. 6 Additional grounding of the cable shields at the entry point of a cabinet 27 
Fig. 7 Isolated communication link 28 
Fig. 8 Non-isolated communication link with common chassis potential 29 
Related Documents 
 
 
 

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 5 von 37

1Introduction

1.1 General Remarks

The content and presentation of this document has been carefully checked. No responsibility is accepted for any errors or omissions in the

documentation.

Note that the documentation for the products is constantly revised and improved. The right to change this documentation at any time without

notice is therefore reserved.

Syslogic is grateful for any help referring to errors or for suggestions for improvements.

The following registered trademarks are used:

IBM-PC, PC/AT, PS/2 trademarks of IBM Corporation

SPI trademark of Motorola

I2C trademark of Philips Corporation

Intel Atom trademark of Intel Corporation

Windows Embedded Compact trademark of Microsoft Corporation

Windows Embedded Standard trademark of Microsoft Corporation

All other trademarks appearing in this document are the property of their respective company.

1.2 Explanation of Symbols

1.2.1 Danger warnings

The following information is for your personal safety and the prevention of damage to the product described or connected devices.

Safety instructions and warnings for the prevention of danger to the life and health of users or service personnel and for the prevention of

damage are highlighted in this document by the pictograms specified below.

Warning

and

Information

pictograms are shown in this document.

1.2.2 Warnings indicate the following:

Death, serious injury or substantial material damage may occur if the related safety measures are not implemented.

The individual

Warning

pictograms have the following meaning:

Attention! General!

Is an instruction that must be observed in order to ensure protection before, while

and after using the device. The correct procedure must be observed.

Attention! Electric shock!

Persons may be exposed to dangerous voltages in electrical installations.

There is a danger of electric shock if a live part is touched.

Attention! Observe ESD measures!

Electrostatic discharge may destroy electronic components.

Attention! Hot surfaces

Keep clear of surfaces. They may be hot.

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 6 von 37

1.2.3 Information pictograms indicate the following:

Important information about the product or the relevant section of the document requiring the particular attention of the reader is marked as

followed:

Indicates important and instructional information.

1.3 Copyright note

This documentation is the intellectual property of Syslogic Datentechnik AG, which also has the exclusive copyright. Any modification of the

content, duplication or reprinting of this documentation, as well as any distribution to third parties can only be made with the express permission

of Syslogic Datentechnik AG.

Syslogic Datentechnik AG does not accept any liability for damages arising from the use of any incorrect or incomplete information contained in

this documentation or any information missing.

All brand and product names are trademarks or registered trademarks of the owner concerned.

1.4 Contents of this Documentation

This document addresses to system integrators, programmers and instructed installation and maintenance personal working with the C-Series

Touch-PC system. It provides all information needed to configure setup and program the product.

1.5 Additional Products and Documents

1.5.1 Hardware Products

The following hardware products are mandatory together with this documentation:

PSU/DT24V60W-3A - 24V Desktop Power Supply 60W - 3 pole

or an equivalent CE-compliant AC/DC power supply

1.5.2 Software Products

There are no additional software products except operating systems:

–Operating Systems: check chapter 5.4 for a list of supported implementations.

1.5.3 Documents

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 7 von 37

1.6 Items delivered

1.1.1. Built-in version

-1x TFT/HB101PU81xxx-C001y

-1x Fixing Frame with M3x6 and M3x8 securing screws

-1x Power supply connector Weidmüller BCZ 3.81/03/180F SN SW (1792960000)

1.1.2. To be purchased separately

-CE-compliant power supply

e.g. PSU/DT24V60W-3A - 24V Desktop Power Supply 60W - 3 pole

1.7 Installation

The installation of the system is described in chapter 3 of this documentation.

1.8 Safety Recommendations and Warnings

The products are intended for measurement, control and communications applications in industrial environments. The products must be

assembled and installed by specially trained people. The strict observation of the assembly and installation guidelines is mandatory.

The use of the products in systems in which the life or health of persons is directly dependent (e.g. life support systems, patient monitoring

systems, etc.) is not allowed.

The use of the products in potentially explosive atmospheres requires additional external protection circuitry which is not provided with the

products.

In case of uncertainty or of believed errors in the documentation please immediately contact the manufacturer (address see chapter 7.1). Do not

use or install the products if you are in doubt. In any case of misuse of the products, the user is solely liable for the consequences.

1.8.1 General warnings

Important note

Ensure that the power supply is disconnected from the device before working on the

device (connecting interfaces, replacing flash cards, batteries, opening the enclosure,

etc.).

Important note

The output voltage of the external power supply shall be SELV and shall be limited

power source according to clause 2.5 EN 60950-1.

Please read the safety instructions of the power supply before installing/connecting

the device.

1.8.2 EMC

Important note

This is a Class A product and not intended to be used in domestic environment. The

product may cause electromagnetic interference. Appropriate measures must be

taken.

Important note

To fullfill class A of EN55032 and EN55035 a CE-compliant AC/DC power supply

must be used. Cable length between power supply and device is limited to 3m.

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 8 von 37

1.8.3 Electro Static Discharge

Electronic boards are sensitive to Electro-Static Discharge (ESD). Please ensure that

the product is handled with care and only in an ESD protected environment.

Otherwise a proper operation is not guaranteed.

1.8.4 Battery

Changing batteries

Danger of explosion if the battery is not correctly replaced. Replace only with the same

or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Maintenance of battery

Empty batteries may leak.

Never short the battery.

1.8.5 Hot surface

Attention! Hot surfaces

Make sure the device is not hot before mounting or changing the installation. The

device may be hot and may cause burs.

1.9 Life Cycle Information

1.9.1 Transportation and Storage

During transportation and storage, the products must be in their original packing. It is recommended, to keep the original packing in case of

return of the product to the factory for repair. Note that the packing is recyclable.

1.9.2 Assembly and Installation

Observe the EMI-precautions against static discharge. Carefully read the installation documentation before unpacking the product.

The installation procedures must be strictly observed. Note that deviations from the installation guidelines may result in degraded operational

reliability or in unfavourable EM-radiation or EM-susceptibility.

1.9.3 Operation

The operating environment must guarantee the environmental parameters (temperature, power supply, etc.) specified in the technical

specification section of this document.

The main functionality of the product is defined by the application program. The application program is not part of the delivery by Syslogic but

is defined, developed and tested by the customer or a system-integrator for each specific application. Refer to the respective documentation for

more information.

1.9.4 Maintenance and Repair

In the rare case of a product hardware-failure or malfunction, the complete product should be exchanged. The faulty product must be returned

to the factory for repair. Please use whenever possible the original packing for return of the product (EMI and mechanical protection).

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 9 von 37

1.9.5 Disposal

At the end of the lifespan the C-Series Touch-PC products must be properly disposed. C-Series Touch-PC products contain a multitude of elements

and must be disposed like computer parts. The C-Series Touch-PC products contain batteries which should be properly disposed.

1.9.6 RoHS

The products of the C-Series Touch-PC family are designed and produced according to the Restriction of Hazardous Substances (RoHS) Directive

(2011/65/EU).

1.9.7 WEEE

The products of the C-Series Touch-PC family are not designed ready for operation for the end-user and are not intended for consumer

applications. According to Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) Syslogic takes back defective devices for

proper disposal at the point of sale.

C-Series Touch-PC: user documentation

DOC/ C-Series_Touch-PC; V1.1

DOC_C-Series_Touch-PC_V1.1.docx Seite 10 von 37

2Product Description

2.1 Introduction

2.1.1 Benefits of Syslogic`s Projected capacitive touch panels

The product meets all the requirements of state-of-the-art advanced Panel Computer.

The TFT technology makes a wide range of applications possible with a perfect and clear picture on an absolutely flat surface.

A metal housing with a solid front frame and scratch resistant glass protects the device

A robust touch screen technology is used.

The product is an information display and input device providing a front protection of IP65.

The absolutely flat PCT (Projected capacitive Touch) touch panel offers the latest Multi-Touch technology. PCT Touch Screen can be used with

fingers or with special capacitive touch or thin latex gloves. The touchscreen is self-calibrating.

The device is reliably during long periods of use and requires little care and maintenance.

The product is available for long term.

2.1.2 Intended use of Projected Capacitive Touch Panels

The Projected Capacitive Touch Panel is designed for:

–Visualization and process control

–General control and automation tasks

–Industrial use

–For multi-media systems

–Operation in the ambient conditions specified in the technical data

This device description is designed as a reference guide for the installation, connection, operation and maintenance of all versions of the Projected

Capacitive Panel, and also provides all the relevant technical data.

2.2 Device Variants

The Projected capacitive touch panels are available in the following versions:

Standard temperature

Order code

Flat screen

Mounting type

Memory

CPU

Flash

TFT/HB101PU81G13-C001S

10.1” WXGA

Flush mounting

2GB

Intel x5-E3930 dual core 1.8GHz

64GB

TFT/HB101PU81H18-C001S

10.1” WXGA

Flush mounting

4GB

Intel x5-E3940 quad core 1.8GHz

64GB

TFT/HB101PU81I20-C001S

10.1” WXGA

Flush mounting

8GB

Intel x7-E3950 quad core 2.0GHz

64GB

Tab. 1 Projected capacitive touch panel versions

Extended temperature

Order code

Flat screen

Mounting type

Memory

CPU

Flash

TFT/HB101PU81G13-C001E

10.1” WXGA

Flush mounting

2GB

Intel x5-E3930 dual core 1.8GHz

64GB

TFT/HB101PU81H18-C001E

10.1” WXGA

Flush mounting

4GB

Intel x5-E3940 quad core 1.8GHz

64GB

TFT/HB101PU81I20-C001E

10.1” WXGA

Flush mounting

8GB

Intel x7-E3950 quad core 2.0GHz

64GB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere syslogic Touchscreen Handbücher

syslogic

syslogic TFT/HB101PU Series Bedienerhandbuch

syslogic

syslogic IPC/RSL8-X E Series Bedienerhandbuch

syslogic

syslogic TFT/HB PU8 Series Bedienerhandbuch

syslogic

syslogic TFT/PANxxxIS-F1 Series Bedienungsanleitung

syslogic

syslogic TFT/HB PU71 16 Series Bedienerhandbuch

syslogic

syslogic TFT/PB101PU-C Bedienerhandbuch

syslogic

syslogic TFT/PB101PU Series Bedienerhandbuch

syslogic

syslogic TFT/HMIxxxIS6-1A Series Bedienungsanleitung

syslogic

syslogic TFT/HB101PR8 Series Bedienerhandbuch

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung

syslogic C Series Bedienerhandbuch

Beliebte Touchscreen Handbücher anderer Marken