System air SAVE VTR 100/B Bedienungsanleitung

Document translated from English | 212234 · A001

SAVE VTR 100/B Electrical reheater installation

GB Installation instructions ................................2

SV Installationsinstruktion .................................8

DE Installationsanleitung.................................14

NO Montasjeanvisning ....................................20

FI Asennusohjeet ..........................................26

212234 | A001

E&OE

Systemair UAB reserves the rights to change their products without notice.

This also applies to products already ordered, as long as it does not affect the previously agreed specifications.

Systemair is not liable or bound by the warranty if these instructions are not adhered to during installation or service.

212234 | A001

Contents

1 Installation.....................................................5

1.1 TRIAC installation (right-hand

orientation)...........................................6

1.2 TRIAC installation (left-hand

orientation)...........................................7

2 Configuration .................................................7

GB Installation | 5

1 Installation

Danger

• Make sure that the mains supply to the unit is disconnected before performing any maintenance or

electrical work!

• All electrical connections and maintenance work must be carried out by an authorized installer and in

accordance with local rules and regulations.

Warning

• Beware of sharp edges during mounting and maintenance. Use protective gloves.

1 Remove the cover of the unit.

Insert reheater (1).

2 Use included plastic knob (2) to secure inserted re-

heater in place. Connect cable from reheater to con-

nector at the top of compartment (3).

Cable contains control signal wires and wires from an

overheat protection sensor.

3 Install and connect TRIAC (component responsible for

temperature detection). Installation method and posi-

tion differs based on VTR 100/B unit orientation.

212234 | A001

6| Installation GB

1.1 TRIAC installation (right-hand orientation)

1RIGHT-HAND ORIENTATION (default from factory, out-

door air connection is situated on the right-hand side

of the unit when viewed from the front)

Remove a screw from the panel inside (1).

Slightly lift and remove the panel (2) in order to ac-

cess the main circuit board.

Peel off label which covers a hole for TRIAC (3).

2 Lift the main circuit board off the hooks (1) and care-

fully pull it out.

Lead TRIAC (2) wires through the hole in the previ-

ously removed panel, insert TRIAC and use included

screws (3) to secure TRIAC in place.

Note:

Make sure TRIAC is facing the correct

direction. Cables must face the main circuit

board.

Connect wires to the main circuit board connector (4).

See wiring diagram for more information.

3 Insert back the main circuit board together with the

panel.

Note:

Make sure not to damage connected the

wires.

Tighten the panel with previously removed screw.

Put the cover back.

212234 | A001

GB Configuration | 7

1.2 TRIAC installation (left-hand orientation)

1LEFT-HAND ORIENTATION (outdoor air connection is

situated on the left-hand side of the unit when

viewed from the front)

Remove a screw from the front panel (1).

Peel off label which covers holes for TRIAC screws.

Position TRIAC (2) over holes and use included screws

(3) to secure TRIAC in place.

Lift the main circuit board off the hooks (5) and care-

fully pull it out.

Connect wires to the main circuit board connector (4).

See wiring diagram for more information.

Insert back the main circuit board.

Tighten the panel with previously removed screw (1).

Put the cover back.

2 Configuration

1. Go to Service menu

2. Enter password (default 1111)

3. Go to Components menu, select Heater menu and select type as Electrical. Do advanced settings if necessary.

4. Configure overheat protection sensor. Go back to Input menu. Select ANALOG tab. Select the analog input to which

the overheat protection sensor is connected. Example if it is connected to AI4 on the main circuit board, then select

ANALOG INPUT 4 and select Overheat Temperature Sensor (OHT) from the input type list.

5. Configure TRIAC. Go to Output menu. Select ANALOG tab then select TRIAC OUTPUT and set output type as Y1

Heating.

Note:

If the supply air temperature is low, it can indicate that the over heat protection is triggered. The overheat

protection can be reset by pressing the reset button.

212234 | A001

2122341 | A001

Alla rättigheter förbehållna

Med förbehåll för eventuella fel och förbiseenden

Systemair AB förbehåller sig rätten att ändra produkterna utan föregående meddelande.

Detta gäller även redan beställda produkter, så länge det inte påverkar tidigare överenskomna specifikationer.

Systemair kan inte hållas ansvarigt för eventuella skador eller följdskador och garantin upphör att gälla om dessa anvisningar inte följs

vid installation eller vid service.

2122341 | A001

Innehåll

1 Installation................................................... 11

1.1 TRIAC-installation

(högerutförande) ................................. 12

1.2 TRIAC-installation

(vänsterutförande) ............................... 13

2 Konfiguration ............................................... 13

Andere Handbücher für SAVE VTR 100/B

Inhaltsverzeichnis

Sprachen:

Andere System air Lüfter Handbücher

System air

System air Villavent Duo TSL-2 Bedienungsanleitung

System air

System air CAP-C Bedienungsanleitung

System air

System air Fantech DPV22-2 Handbuch

System air

System air Living HP Fehlerbehebungshandbuch

System air

System air VTR 200 Bedienungsanleitung

System air

System air VX-400 EV Bedienungsanleitung

System air

System air AXS Series Bedienungsanleitung

System air

System air SAVE VSR 150/B Handbuch

System air

System air SAVE VTR 200/B Bedienungsanleitung

System air

System air VR-250 EH/B/3 Bedienungsanleitung

System air

System air SYSVRF2 DUCT HP 71 Q Bedienungsanleitung

System air

System air SAVE VTC 200-1 Bedienungsanleitung

System air

System air RS Series Handbuch

System air

System air Fantech FLEX VHR 150R Bedienungsanleitung

System air

System air PRF 125D2 Bedienungsanleitung

System air

System air fantech RCS80L Handbuch

System air

System air DVCompact DXR-10 Handbuch

System air

System air SAVE VTC 300 Bedienungsanleitung

System air

System air Fantech prioAir 6 Bedienungsanleitung

System air

System air Villavent VX-250 TV/P Bedienungsanleitung

System air

System air AXC Bedienungsanleitung

System air

System air Multibox MUB Series Bedienungsanleitung

System air

System air KBR 315EC Bedienungsanleitung

System air

System air Topvex SoftCooler SR11 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung