System Sensor MP120KLA Bedienungsanleitung
1 I56-9107-002
12/13/2018
PRODUCT SPECIFICATIONS
Standard Operating Temperature: –40°F to 151°F (–40°C to 66°C)
Humidity Range: 10 to 93% non-condensing (indoor products)
Nominal Voltage: Regulated 120 VAC
Operating Voltage Range: 96-132 VAC
Current Draw From AC Line: 150 mA max.
MP120KLA may be used with any standard L-Series indoor Horns, Strobes, or Horn Strobes, at all horn and strobe settings.
NOTICE: This manual shall be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The MP120KLA mounting plate is designed to allow the use of 120 VAC to
power L-Series indoor horn, strobes, horn strobes, chimes, and chime strobes.
The MP120KLA consists of a mounting plate that has been fitted with a power
supply that converts 120VAC to nominal 24V FWR.
The MP120KLA must be installed using a 120 VAC power source. This unit
can only be used for non-synchronous applications; it will NOT work with
System Sensor Sync•Circuit Modules.
WIRING
This module has pig-tail wires and is intended to be wired without rigid con-
nections inside a standard electrical box.
INSTALLATION AND MAINTENANCE INSTRUCTIONS
6335 Edwards Blvd. Mississauga, ON L5T 2W7
800/736-7672, FAX: 905-812-0771
www.systemsensor.ca
MP120KLA
120 VAC Adapter Mounting Plate
MOUNTING (WALL)
1. For indoor applications, attach the mounting plate as shown in Figure 2.
The mounting plate is compatible only with 4 × 4 electrical boxes.
2. Connect field wiring. (For indoor models only)
3. If the product is not to be installed at this point, use the protective dust
cover to prevent contamination of the mounting plate terminals.
4. To attach product to mounting plate:
a. Remove the protective dust cover.
b. Hook the tabs on the top of the product housing into the grooves on
mounting plate.
c. Pivot the product into position to engage the terminals on the mount-
ing plate. Make sure that the tabs on the back of the product housing
fully engage with the mounting plate.
d. Hold product in place with one hand, and secure product by tighten-
ing the single mounting screw in the front of the product housing.
FIGURE 1. NON-SYNCHRONIZED DEVICES; ANY COMBINATION OF MODELS POWERED BY A 2-WIRE CIRCUIT
Horn Strobe Only
Two Wire System
An
y Mix of Models
Wired for Tandem
Operation
120
VAC
Power
Horn Strobe
A0356-01
FIGURE 2. WALL-MOUNTING (INDOOR ONLY)
4x4x21/8" BACKBOX 120V WIRES 120V MOUNTING PLATE
(Shipped mounted to MP120KL Module)
L-SERIES WALL-MOUNT
NOTIFICATION APPLIANCE
A0526CDN-01
I56-9107-002
2 I56-9107-002
©2018 System Sensor. 12/13/2018
System Sensor®is a registered trademark of Honeywell International, Inc.
FIGURE 3. CEILING-MOUNTING (INDOOR ONLY)
L-SERIES CEILING-MOUNT
NOTIFICATION APPLIANCE
4x4x21/8" BACKBOX 120V MOUNTING PLATE
(Ships with Notification Appliance)
120V WIRES
MP120KLA MODULE
(Mounting plate removed)
A0573CDN-00
MOUNTING (CEILING)
Indoor L-Series ceiling appliances use a round mounting plate that is not sup-
plied with the MP120KLA. The mounting plate that ships with the notification
appliance will need to be attached to the MP120KLA module.
1. Remove the mounting plate which comes attached to the MP120KLA
module. Disconnect the red and black wire and remove the 4 mounting
screws that attach the mounting plate to the MP120KLA module.
2. Attach the round mating plate that ships with the notification appliance
to the MP120KLA module. Attach with the 4 screws from Step 1 and
attach the red and black wires to the terminal screws.
3. Attach the mounting plate as shown in Figure 3. The mounting plate is
compatible only with 4 × 4 electrical boxes.
4. Connect field wiring to the mounting plate per the notification appliance
user manual.
FCC STATEMENT
System Sensor Strobes and Horn/Strobes have been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This class B digital apparatus complies with Canadian ICES-003.
For the latest Warranty information, please go to:
http://www.systemsensor.com/en-us/Documents/E56-4000.pdf
For Limitations of Fire Alarm Systems, please go to:
http://www.systemsensor.com/en-us/Documents/I56-1558.pdf
Speakers only: For the latest Important Assembly Information, please go to:
http://www.systemsensor.com/en-us/Documents/I56-6556.pdf
Warranty
Limitations of
Fire Alarm Systems
Speakers Only:
Assembly Information
SUPPLEMENTAL INFORMATION
5. If the product is not to be installed at this point, use the protective dust
cover to prevent contamination of the mounting plate terminals.
6. To attach product to mounting plate:
a. Remove the protective dust cover.
b. Hook the tabs on the top of the product housing into the grooves on
mounting plate.
c. Pivot the product into position to engage the terminals on the mount-
ing plate. Make sure that the tabs on the back of the product housing
fully engage with the mounting plate.
d. Hold product in place with one hand, and secure product by tighten-
ing the single mounting screw in the front of the product housing.
Ceiling Models only: To remove product from the mounting plate, loosen the
captive mounting screw and press the locking button.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere System Sensor Adapter Handbücher
