Tacony Baby Lock Flare Technisches Handbuch

Thank you for purchasing this machine. Before using this

machine, carefully read the “IMPORTANT SAFETY

INSTRUCTIONS”, and then study this manual for the

correct operation of the various functions.

In addition, after you have finished reading this manual,

store it where it can quickly be accessed for future

reference.

Please read these safety instructions before attempting to

use the machine.

DANGER

- To reduce the risk of electrical shock

1Always unplug the machine from the

electrical outlet immediately after using,

when cleaning, making any user

servicing adjustments mentioned in this

manual, or if you are leaving the

machine unattended.

WARNING

- To reduce the risk of burns, fire, electrical shock, or

injury to persons.

2Always unplug the machine from the electrical

outlet when making any adjustments mentioned in

the instruction manual.

• To unplug the machine, switch the machine to the

symbol “O” position to turn it off, then grasp the

plug and pull it out of the electrical outlet. Do not

pull on the cord.

• Plug the machine directly into the electrical outlet.

Do not use an extension cord.

• Always unplug your machine if there is a power

failure.

3Electrical Hazards:

• This machine should be connected to an AC power

source within the range indicated on the rating

label. Do not connect it to a DC power source or

inverter. If you are not sure what kind of power

source you have, contact a qualified electrician.

• This machine is approved for use in the country of

purchase only.

4Never operate this machine if it has a damaged cord

or plug, if it is not working properly, has been

dropped or damaged, or water is spilled on the unit.

Return the machine to the nearest authorized Baby

Lock retailer for examination, repair, electrical or

mechanical adjustment.

• While the machine is stored or in use if you notice

anything unusual, such as an odor, heat,

discoloration or deformation, stop using the

machine immediately and unplug the power cord.

• When transporting the machine, be sure to carry it

by its handle. Lifting the machine by any other part

may damage the machine or result in the machine

falling, which could cause injuries.

• When lifting the machine, be careful not to make

any sudden or careless movements, which may

cause a personal injury.

5Always keep your work area clear:

• Never operate the machine with any air openings

blocked. Keep ventilation openings of the machine

free from the build up of lint, dust, and loose cloth.

• Never drop or insert foreign objects in any opening.

• Do not operate where aerosol (spray) products are

being used or where oxygen is being administered.

• Do not use the machine near a heat source, such as

a stove or iron; otherwise, the machine, power cord

or garment being embroidered may ignite, resulting

in fire or an electric shock.

• Do not place this machine on an unstable surface,

such as an unsteady or slanted table, otherwise the

machine may fall, resulting in injuries.

6Special care is required when embroidering:

• Always pay close attention to the needle. Do not use

bent or damaged needles.

• Keep fingers away from all moving parts. Special

care is required around the machine needle.

INTRODUCTION

IMPORTANT SAFETY

INSTRUCTIONS

• Switch the machine to the symbol “O” position to

turn it off when making any adjustments in the

needle area.

• Do not use a damaged or incorrect needle plate, as

it could cause the needle to break.

7This machine is not a toy:

• Your close attention is necessary when the machine

is used by or near children.

• The plastic bag that this machine was supplied in

should be kept out of the reach of children or

disposed of. Never allow children to play with the

bag due to the danger of suffocation.

• Do not use outdoors.

8For a longer service life:

• When using and storing this machine, avoid direct

sunlight and high humidity locations. Do not use or

store the machine near a space heater, iron, halogen

lamp, or other hot objects.

• Do not use cleansers or organic solvents, such as

thinner, petroleum ether or alcohol, to clean the

machine. Otherwise, the finish may peel off or

become scratched.

• Always consult the Instruction and Reference Guide

when replacing or installing any assemblies, the

presser feet, needle or other parts to assure correct

installation.

9For repair or adjustment:

• If the light unit is damaged, it must be replaced by

an authorized Baby Lock retailer.

• In the event a malfunction occurs or adjustment is

required, first follow the troubleshooting table in the

back of the Instruction and Reference Guide to

inspect and adjust the machine yourself. If the

problem persists, please consult your local

authorized Baby Lock retailer.

Use this machine only for its intended use as described

in the manual.

Use accessories recommended by the manufacturer as

contained in this manual.

The contents of this manual and specifications of this

product are subject to change without notice.

For additional product information and updates, visit

our website at www.babylock.com

SAVE THESE

INSTRUCTIONS

This machine is intended

for household use.

FOR USERS IN COUNTRIES

EXCEPT EUROPEAN COUNTRIES

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance.

FOR USERS IN EUROPEAN

COUNTRIES

This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory

or mental capabilities or lack of

experience and knowledge if they have

been given supervision or instruction

concerning use of the appliance in a

safe way and understand the hazards

involved. Children shall not play with

the appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

FOR USERS IN THE UK,

EIRE, MALTA

AND CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

• Always replace the fuse cover. Never use plugs with

the fuse cover omitted.

• If the available electrical outlet is not suitable for the

plug supplied with this equipment, you should

contact your authorized Baby Lock retailer to obtain

the correct lead.

Federal Communications

Commission (FCC)

Supplier’s Declaration of

Conformity (For U.S.A.

Only)

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired

operation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the authorized Baby Lock retailer or an

experienced radio/TV technician for help.

• This transmitter must not be co-located or operated

in conjunction with any other antenna or

transmitter.

Important

Changes or modifications not expressly approved by

Tacony Corporation could void the user’s authority to

operate the equipment.

This equipment complies with FCC/IC radiation

exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF)

Exposure Guidelines and RSS-102 of the IC radio

frequency (RF) Exposure rules. This equipment should

be installed and operated keeping the radiator at least

20cm or more away from person’s body.

Responsible Party: Tacony Corporation

1760 Gilsinn Lane, Fenton,

Missouri 63026 U.S.A.

declares that the product

Product Name:

Model Number:

Baby Lock Embroidery Machine

BLMFL

For Users in Canada

This device complies with Industry Canada’s licence-exempt

RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets the

FCC radio frequency (RF) Exposure Guidelines and RSS-102

of the IC radio frequency (RF) Exposure rules. This equipment

should be installed and operated keeping the radiator at least

20cm or more away from person’s body.

For Users in Mexico

The operation of this equipment is subject to the following

two conditions:

(1) it is possible that this equipment or device may not cause

harmful interference, and

(2) this equipment or device must accept any interference,

including interference that may cause undesired

operation.

La operación de este equipo está sujeta a las siguientes dos

condiciones:

(1) es posible que este equipo o dispositivo no cause

interferencias perjudiciales y

(2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su

operación no deseada.

IMPORTANT-PLEASE READ

CAREFULLY:

This Terms of Use (“Agreement”) is a legal agreement

between Tacony Corporation (“Company”) and you that

governs your use of any Software, installed on or made

available by Company for use with sewing or craft products

(“Company Product”). The term of “Software” means any and

all contents data, design data, data format, firmware of

Company Product, and PC application or mobile device

application.

By using the Software and Company Product, you shall be

deemed to have agreed to be bound by the terms of this

Agreement. If you do not agree to the terms of this Agreement,

Company is unwilling to license the Software and you are not

allowed to use the Software. Amendments and supplements to

this Agreement may be attached to the Software.

An individual who accepts this Agreement on behalf of an

entity represents to Company that he or she has the legal right

to enter into a binding legal agreement for that entity.

Terms and Conditions

1 Grant of License.

1.1 Subject to this Agreement, Company hereby

grants you a personal, non-exclusive, non-

transferable and revocable license to use the

Software only within the Company Product.

1.2 Your right to use of the Software is licensed and

not sold, and solely for your use subject to this

Agreement. Company or its suppliers retains all

right, title, and interest relating to Software,

including without limitation all intellectual

property rights relating thereto.

2 Restrictions

2.1 Except as expressly set out in this Agreement or

as required by any local law, you shall

undertake:

2.1.1 not to disassemble, de-compile, reverse

engineer, translate or otherwise attempt

to learn the source code of the Software

(including the data or contents created

by using the Company Product or

contents editing application software;

hereinafter the same shall apply in this

Clause 2.);

2.1.2 not to create derivative works based on

the whole or any part of the Software;

2.1.3 not to distribute, provide or make

available the Software in any form, in

whole or in part to any person without

prior written consent from Company;

2.1.4 not to copy the Software, except where

such copying is incidental to normal

use of the Software with Company

Product or where it is necessary for the

purpose of back-up or operational

security;

2.1.5 not to transfer, rent, lease, sub-license,

loan, translate, merge, adapt, vary, alter

or modify, the whole or any part of the

Software nor permit the Software or any

part of it to be combined with, or

become incorporated in, any other

programs;

2.1.6 to include Company’s copyright notice

and this Agreement on all entire and

partial copies of the Software; and

2.1.7 not to use the Software for any purpose

(including, but not limited to, use with

unauthorized sewing/craft products or

software) other than as provided under

Clause 1 of this Agreement.

3Nowarranty

TO THE EXTENT PERMISSIBLE BY

APPLICABLE LAW, THIS SOFTWARE IS

PROVIDED TO YOU “AS IS” WITHOUT

WARRANTIES OR CONDITIONS OF ANY

KIND, WHETHER ORAL OR WRITTEN,

EXPRESS OR IMPLIED. COMPANY

SPECIFICALLY DISCLAIMS ANY IMPLIED

WARRANTIES OR CONDITIONS OF

MERCHANTABILITY, SATISFACTORY

QUALITY, NON-INFRINGEMENT AND/OR

FITNESS FOR A PARTICULAR PURPOSE.

4 Limitation of liability

4.1 COMPANY SHALL NOT BE LIABLE TO YOU,

ITS END-USERS OR ANY OTHER ENTITY FOR

ANY LOSS OF PROFITS OR INCOME OR

SAVINGS, LOSS OF DATA, INTERRUPTION

OF USE, OR CONSEQUENTIAL,

INCIDENTAL, SPECIAL, PUNITIVE OR

INDIRECT DAMAGES INCURRED BY SUCH

PARTY (WHETHER IN AN ACTION IN

CONTRACT OR TORT), EVEN IF COMPANY

HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES, ARISING OUT OF OR

RELATING TO THE SOFTWARE, SUPPORT

SERVICE OR THIS AGREEMENT. THESE

LIMITATIONS SHALL APPLY TO THE

MAXIMUM EXTENT ALLOWED BY

APPLICABLE LAW NOTWITHSTANDING

ANY FAILURE OF ESSENTIAL PURPOSE OF

ANY LIMITED REMEDY.

4.2 NOTWITHSTANDING THE CLAUSE 3 OR 4.1

HEREOF, THIS AGREEMENT DOES NOT

PURPORT TO EXCLUDE OR RESTRICT

COMPANY’S LIABILITY FOR DEATH OR

PERSONAL INJURY RESULTING FROM

NEGLIGENCE OR LIMIT THE STATUTORY

RIGHTS OF A CONSUMER.

5Termination

5.1 Company shall have the right to terminate this

Agreement at any time by providing a written

notice to you if you commit a material breach

of any terms of this Agreement and fail to

immediately rectify such breach upon

Company’s request.

5.2 Upon termination for any reason all rights

granted to you under this Agreement shall

cease, you shall cease all activities authorized

by this Agreement and you shall immediately

delete or remove the Software from all

computer equipment in your possession and

delete or destroy all copies of the Software or

its derivative works in your possession. In

addition to the above, you shall delete contents

or design data created by you from the

Company Product in your possession.

6 Miscellaneous terms

6.1 You shall not export or re-export the Software

or any copy or adaptation thereof in violation

of any applicable laws or regulations.

6.2 You shall not assign all or any part of this

Agreement to any third party or any interest

therein, without prior written consent of

Company. A change of control or

reorganization of you pursuant to a merger,

sale of assets or stock shall be deemed to be an

assignment under this Agreement.

6.3 You agree that a breach of this Agreement will

cause irreparable injury to Company for which

monetary damages would not be an adequate

remedy and Company shall be entitled to seek

equitable relief in addition to any remedies it

may have hereunder or at law without a bond,

other security, or proof of damages.

6.4 If any provisions of this Agreement shall be

declared or determined as void or

unenforceable by a court of competent

jurisdiction, such provisions shall be severable

and independent from the other provisions of

this Agreement and the validity of the other

provisions and of the entire Agreement shall

not be affected thereby.

6.5 This Agreement, together with all exhibits or

other attachments referenced herein,

constitutes the entire agreement between the

parties on the subject matter hereof, and

supersedes all proposals, oral and written,

between the parties on this subject.

6.6 If Company fails to insist that you perform any

of your obligations under this Agreement, or if

Company does not enforce any rights against

you, or if Company delay in doing so, that will

not mean that Company have waived any

rights against you and will not mean that you

do not have to comply with those obligations.

If Company does waive a default by you,

Company will only do so in writing, and that

will not mean that Company will automatically

waive any later default by you.

6.7 This Agreement is governed by the laws of

Japan and Japanese Courts shall have exclusive

jurisdiction with respect to this Agreement

except with regard to enforcement in which

case the jurisdiction of the Japanese Courts

shall be non-exclusive.

6.8 The Company may update this Agreement in

the below cases: A) When the changes are

made for the users' benefit, or B) When the

updates to the Agreement are adequate,

reasonable, and not contrary to the purposes of

the Agreement.

The Company will notify you and give you the

opportunity to review any material changes or

updates to the Agreement, by posting a notice

on the Company's website or a website

specified by the Company at least 30 days

before the Agreement enters into effect. Once

the updated Agreement is in effect, you will be

bound by it if you continue to use the Software.

Make sure you use a router or firewall when connecting

your machine to the Internet to protect it against

unauthorized access from the Internet.

Any trade names and product names of companies appearing on

Baby Lock products, related documents and any other materials are

all trademarks or registered trademarks of those respective

companies.

This product includes software developed by the following

vendor:

PRECAUTION FOR WIRELESS

CONNECTION

TRADEMARKS

IMPORTANT:

READ BEFORE DOWNLOADING, COPYING,

INSTALLING OR USING.

By downloading, copying, installing or using the

software you agree to this license. If you do not

agree to this license, do not download, install,

copy or use the software.

Intel License Agreement For Open

Source Computer Vision Library

copyrights are property of their respective owners.

Redistribution and use in source and binary forms,

with or without modification, are permitted provided

that the following conditions are met:

• Redistribution’s of source code must retain the

above copyright notice, this list of conditions and

the following disclaimer.

• Redistribution’s in binary form must reproduce the

above copyright notice, this list of conditions and

the following disclaimer in the documentation and/

or other materials provided with the distribution.

• The name of Intel Corporation may not be used to

endorse or promote products derived from this

software without specific prior written permission.

This software is provided by the copyright holders and

contributors “as is” and any express or implied

warranties, including, but not limited to, the implied

warranties of merchantability and fitness for a

particular purpose are disclaimed. In no event shall

Intel or contributors be liable for any direct, indirect,

incidental, special, exemplary, or consequential

damages (including, but not limited to, procurement

of substitute goods or services; loss of use, data, or

profits; or business interruption) however caused and

on any theory of liability, whether in contract, strict

liability, or tort (including negligence or otherwise)

arising in any way out of the use of this software, even

if advised of the possibility of such damage.

All information provided related to future Intel products and plans is

preliminary and subject to change at any time, without notice.

WPA™ and WPA2™ are trademarks of Wi-Fi Alliance®.

CONTENTS

Chapter 1 GETTING READY 9

Names of Machine Parts....................................... 9

Included accessories ............................................................ 11

Optional accessories ............................................................ 12

Turning the Machine On/Off.............................. 13

LCD Operation ................................................... 14

Settings screen...................................................................... 14

Adjusting input sensitivity for operation keys........................ 15

Wireless Network Connection Functions............ 16

Operations available with a wireless network connection .... 16

Enabling a wireless network connection............................... 16

Using the wizard to set up the wireless network

connection ........................................................................... 16

Winding/Installing the Bobbin............................ 18

Winding the bobbin ............................................................. 18

Installing the bobbin............................................................. 21

Upper Threading ................................................ 22

Threading the upper thread .................................................. 22

Replacing the Needle.......................................... 25

Checking the needle............................................................. 25

Replacing the needle............................................................ 25

Chapter 2 EMBROIDERY 27

Embroidering Preparation................................... 27

Attaching the embroidery unit .............................................. 27

Embroidering attractive finishes............................................ 29

Hooping the fabric in the embroidery frame......................... 29

Attaching the embroidery frame ........................................... 31

Embroidering...................................................... 33

Selecting an embroidery pattern ........................................... 33

Embroidering a pattern ......................................................... 36

Embroidery Foot Auto Down................................................ 38

Adjusting thread tension....................................................... 39

Adjusting the bobbin case (with no color on the screw)........ 40

Using the automatic thread cutting function

(End Color Trim)................................................................... 40

Using the Thread Trimming Function (Jump Stitch Trim) ...... 41

Embroidering the appliqué patterns ...................................... 41

Using a frame pattern to make an appliqué .......................... 42

Split embroidery patterns...................................................... 43

Editing Patterns (Pattern Editing Screen) ............ 44

Editing Patterns (Embroidery Settings Screen) .... 46

Aligning the pattern and the needle position ........................ 46

Embroidering linked characters ............................................ 47

Thread color sorting ............................................................. 48

Using the Memory Function ............................... 48

Saving embroidery patterns .................................................. 49

Retrieving embroidery patterns............................................. 49

Chapter 3 APPENDIX 51

Care and Maintenance........................................ 51

Cleaning the LCD................................................................. 51

Cleaning the machine surface .............................................. 51

Restrictions on oiling............................................................ 51

Precautions on storing the machine...................................... 51

Cleaning the race ................................................................. 51

Touch panel is malfunctioning ............................................. 52

Replacing the embroidery foot ............................................. 52

Troubleshooting.................................................. 53

List of symptoms................................................................... 53

Error messages...................................................................... 56

How can I find the wireless security information

(SSID and network key) ........................................................ 58

Operation beeps................................................................... 58

Specifications ..................................................... 59

Updating Your Machine’s Software ................... 59

Index.................................................................. 60

CONTENTS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tacony Nähmaschine Handbücher

Tacony

Tacony Baby Lock Gallant Technisches Handbuch

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Singer

Singer 2517 Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Janome

Janome Quilt Maker Pro 18 VERSA Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung