TAG Heuer HL 675 Bedienungsanleitung

TAGHeuer Timin Page1/8

HL 675 Data / Impulse

Transmitter set

User Manual

Version 02/2015

TAGHeuer Timin Page2/8

1. Global

The Set HL 675 is ideal for transferring Timing Data and Impulses.

Its 500mW emitting power and its licence free frequency range (869 Mhz) makes this device a powerful

and simple to use system.

Data / Impulse transmission system (500 Mw) which does not require a licence (free of use) in Europe

(ISM Band 869 MHz – REC 70-03).

Each Receiver can receive Impulses (simultaneously or not) from 4 Transmitters identified by the

function "CHANNEL" (1 to 4).

Up to 4 Teams can work (train) in the same area without disturbing each other thanks to the function

"TEAM" which offers the possibility to code each system (A, B, C, D).

It is also possible to use up to 16 transmitters with 4 receivers.

When the receiver is switched on, it is possible that one or more green LED’s are on before that the

transmitter(s) start to transmit. This detection system allows visualization of the quality of the

received signal, but also the possible interferences coming from other radio transmission systems. If it

is not possible to stop these interferences by moving the receiver, the transmission of Impulse cannot

be guaranteed.

TAGHeuer Timin Page3/8

1. Functions

1.1. The Transmitter :

1. IMPULSE Input for timing Impulse (Start gate, photocell – working / closing contact). Respect

the polarities.

2. DATA Male Sub-D 9: RS232 input for DATA transfer

2. POWER To switch on the receiver (press for 3 seconds on POWER).

The green LED is on.

To switch off the receiver, hold down SET and press POWER.

4. SET To program the TEAM (A,B,C,D) and to switch off the receiver.

Hold down SET during the changes.

5. TEAM To check the programmed TEAM.

To change the code, hold down SET and press TEAM.

6. CHANNEL To check the programmed CHANNEL.

To change the CHANNEL, hold down SET and press CHANNEL

7. TEST For testing the Impulse transmission only. The reception level will be displayed for

0.2 seconds on the receiver. You’ll also get an Impulse on the programmed

output.

8. TEST BATT To check the state of the battery. Press TEST BATT : The Battery level will be

displayed with the 4 LED’s for 2 seconds.

9. LED LED control panel which shows the programmed TEAM or CHANNEL. Also shows

the transmitted Impulse.

10. LED Shows the transmission mode : IMPULSE or DATA

11. CHARGE Charging status Leds.

The red led indicates that the battery is charging.

The charge is completed as soon as the green LED in on

TAGHeuer Timin Page4/8

1.2. The Receiver

1. IMPULSE Output for timing Impulse (Start gate, photocell – working / closing contact). Respect

the polarities.

2. DATA Female Sub-D 9 : RS232 Output

3. POWER To switch on the receiver (press for 3 seconds on POWER). The green LED is on.

To switch off the receiver, hold down SET and press POWER.

4. SET To program the TEAM (A, B, C, D) and to switch off the receiver. Hold down SET

during the changes.

5. TEAM To check the programmed TEAM. The green LED corresponding to the code A, B, C

or Dis on. To change the code, hold down SET and press TEAM.

6. LED LED control panel which shows the programmed TEAM or CHANNEL. Also shows the

Received Impulse.

7. LED Shows the transmission mode : IMPULSE or DATA

8. LED LED control panel which shows the Receiving Level and/or possible interferences

created by other radio signals.

9. BUZZER To enable or disable the Buzzer

10. TEST BATT To check the Battery status. The Level will be displayed with the 4 LED’s for 4

seconds:

- 4 LED’s on = 80-100%

- 3 LED’s on = 60-80%

- 2 LED’s on = 40-60%

- 1 LED on = 20-40%

- 1 LED on = 0-20% power remaining

5 10

6 8

TAGHeuer Timin Page5/8

2. Battery Charging

Each device has a Lithium-Polymer battery with supply 2100 mAh. Those batteries may be charged

with our charger HL540-10 or other 12V charger with a minimum of 800 mA.

For charging the battery we advise you to use our OEM TAG Heuer charger

Using another model may cause some trouble or harm the device.

-For charging, turn off the system.

- Connect the charger on the mains

- Plug the charger into the device

- The red LED will be on during the charge

IMPORTANT :

Always charge the devices by temperature above 32°F (0°C) and below 86°F (30°C)

The red LED lights during the charging process, when fully charged, the red LED shuts down and the

green LED will light on.

For a fully charged Battery it may take approx. 5 hours (for a completely discharged battery)

WARNING

Never connect the terminals of the battery in short-circuit.

To avoid keeping the battery pack fully loaded or completely discharged for a long period,

which reduces the lifespan of the battery. In the case of prolonged non-utilization of the

battery pack, it is necessary keep the system in a dry room, after a normal discharge.

In case of a reduced capacity of the battery pack, even after the load, leave the system ON a

whole night to obtain a complete discharge, then recharge the battery pack completely.

Renew the battery pack if the problem continues.

3. Software Update

With the Firmware (already used with the Chronoprinter 545 and the Minitimer HL440) able you to change

the transmission mode and Update your device.

New firware for the HL 675 are available free of charge on our website: www.tagheuer-timing.com

For this application you need :

The RS232 cable (HL605-10)

A computer fitted with a D-Sub9 RS232 Output

The software « FirmwareManager.exe »

How to proceed

1. With the radio switched « OFF » connect the external power Connect the RS232 between your

computer and the HL 675

2. Run «FirmwareManager.exe »

TAGHeuer Timin Page6/8

3. Select the correct COM Port

4. Browse and select the correct file (Rx/Tx)

5. Push START on the screen

6. Turn on the HL 675 (hold down for 5 seconds « ON »

The HL 675 will enter in a special setup mode

7. Until the file downloaded then, validate with « OK »

Hands on: Reinitialize your devices

If the systems are in a unknown mode, you can Initialise your system in the OEM

configuration (Channel 1, Team A, Buzzer On, Baud Speed 9600bps, Mode Impulse).

Push simultaneously SET and TEST BATT for 3 seconds.

All LED’s will flash and the system will beep until it is reinitialized.

4. Technical Specification

GeneraloImpulse response precision: +/- 1/10'000 sec

oTransmitting delay: 200ms

oFrequency : 869 MHz REC 70-03

oPower 500 mW

oAutonomy (at +68°F / 20°C) 24 hours (1 Impulse per min.)

8 hours (THbC data transm.)

1 data string each 4 sec.

oImpedance : 50 Ohms

oAntenna 1/4 Wavelength 2.5dBi

oImpulse Input Short-Circuit / Working contact

Respect the polarity

oImpulse Output 4 separated outputs

Isolated by an opto-coupler

Manages up to 4 simultaneous inputs

oChannel : 4 different channels (1,2,3,4)

oTEAM function : 4 different codings (A,B,C,D)

oNormal use temperature between - 4°F (-20°C) and +131°F (+55°C)

oCharging temperature between +32°F (0°C) and +86°F (+30°C)

oSize (without antenna) 152 x 108 x 34 mm

oWeight : 470g / radio

oPower supply : 12 V DC / 800 mA min

Lithium-Polymer Battery

oType 12V Li-Pol 2000mAh

oCharging current 800mA minimum (~ 5 hours)

Charger HL540-10

oPrimary 230V - 50Hz - 125mA

oSecondary 12V – 1250 mA

Warranty : One year after delivery of your purchase

The warranty is null and void under the following conditions:

-if the battery is out of order

TAGHeuer Timin Page7/8

- Poor maintenance and obvious physical damage

- Input or Outputs damaged by poor connection

- If the device was opened without factory authorization

THE INSTALLATION INCLUDES:

1 Plastic case which can store up to 5 Devices

1 to 4 Transmitters

1 Receiver

2 to 5 antennas

1 Charger 100-240 VAC / 9VDC

1 User manual

1 Velcro strap per transmitter

5. Special pinout for Displays HL980 and HL960 / 990

6. Special Pinout for TX activating

Our radios are equipped with a PNP Transistor on their output.

This is an IT Standard which also allows us to ensure good autonomy.

Some devices only work with an RX pin and Ground. In order to activate this transistor and initiate the

external data from the radio you need to energise the Transistor with an external power supply or a

charged condenser.

7. Pinout

Transmitter (male socket)

1NC

2Radio RxD (RS232)

3Radio TxD (RS232)

4RS485 Signal B

5GND

6NC

7RS485 Signal A

8NC

9NC

Receiver (female socket)

1RS485 Signal A

2Radio TxD (RS232)

3Radio RxD (RS232)

4NC

5GND

6NC

7NC

8NC

9RS485 SIGNAL B

To Display HL 960/980

HL 675

To Display HL 980

HL 675

TAG Heuer Timing Page 8 / 8

TAG Heuer

PROFESSIONAL TIMING

6A Louis-Joseph Chevrolet

2300 la Chaux-de-Fonds

Switzerland

Tel : 032 919 8000

Fax : 032 919 9026

E-mail: [email protected]

Http: //www.tagheuer-timing.com

Inhaltsverzeichnis

Andere TAG Heuer Sender Handbücher

TAG Heuer

TAG Heuer HL 670 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung