Tail It Bike Bedienungsanleitung
User manual – Tail it Bike
Tail it Bike user manual
V1.0.0
TAIL IT TECHNOLOGIES | Fossegrenda 9
1
List of content
List of content ................................................................................................................................................ 1
1.Introduction – 3 step installation ................................................................................................................. 2
2.Set up device ............................................................................................................................................... 3
3. Activation of SIM-card ................................................................................................................................ 3
4. Set up and registration in app– Tail it ......................................................................................................... 4
5. Add new device in app – Tail it ................................................................................................................... 5
6. Share device with other users – Tail it ........................................................................................................ 5
7. Update position ......................................................................................................................................... 6
8. General information……………………………………………………………………………………………………….10
9. Position logic……………………………………………………………………………………………………….……10/12
10. Installation of the device.............................………...................................................13/14
2
1.Introduction – 3 step installation
3
1. Open the box you have received and take the tracker and charger out of the box.
2. There will be some power on the battery in your tracker when you receive it, but to
be sure, we recommend that you charge the tracker for a while. Estimated charging
time for full power on the battery is between 3-5 hours. The tracker will blink with a
green light when it is charging and continuously light with a green light when it is
fully charged. (It may take a few seconds for the light to come)
3. Once you have fully charged the tracker you are ready to start the tracker setup.
4. To switch the tracker on, hold down the power button (light source). When you see a
long green light, it means the tracker is turning on. Click the button once quickly, and
if it blinks twice, it’s confirming it’s on. To switch it off again, simply hold the button
down again until you see a long white light.
1. A SIM card is pre-installed inside the device when you receive it. This must be
activated before it can be used. This is done by visiting reg.tailit.com
2. When you go to reg.tailit.com, you can choose which product you have bought, the
subscription type you prefer and fill out the information required.
3. Type in the five-digit IMEI number printed on the sticker that is on your device, or
found on the declaration of conformity inside the box.
3. Activation the SIM-card
2.Set up device
4
4. After you have completed the entire registration, you will receive a message saying
that you have completed activation of the SIM card. Then your SIM card is activated
and ready for use.
5. Once you have activated your SIM card, you will also receive an e-mail with PIN and
PUK codes and mobile number (Check spam if you do not receive the e-mail)
1. Visit the app store (iOs) or Google Play (Android) on your phone and search for "Tail
it" Download this app.
2. The first thing you have to do is register yourself to create a user. Then click Register
at the bottom of the first page or log in through Facebook.
3. If you don’t want to go through Facebook, then enter your own private phone
number to create a user. Next, type the activation code you receive on text on your
mobile.
4. Enter a password. Keep in mind that you must have uppercase letters, lowercase
letters, numbers and a character (!?., - # etc)
5. Enter your own name.
6. Add picture of yourself or skip this step if you dont want to add picture.
4. Set up and registration in app– Tail it
5
1. When you come to the screen where you can add a device, press "Let's get started"
2. Scan the QR code found on the declaration of conformity, or type in the 5 digits you
see on the sticker on the device.
Once you have added the IMEI number, enter the name you want to give the device.
1. Now you've added your device. You can now share this code with someone else, if
you want more people to see the device to their app.
2. In order for someone else to add the device to the app, follow the same recipe as the
setup you already did and enter this code they are asked for after they try entering
the IMEI code you just added. The code expires after 5 minutes, and then a new code
will pop up.
3. Once you have added the device and turned it on, by holding down the power button
(Lightsource on the device), you get to the home screen of your devices. You can also
“swipe” to the left on the device screen, and click the yellow “share” button, to share
it with one of your friends in the app. They will have 5 minutes to accept the
invitation.
5. Add new device in app – Tail it
6. Share device with other users – Tail it
6
4. You can also find this code by pressing on the device in the “devices tab”, where you
will be forwarded to a menu where you can choose to share the device. Then a new
code will be added that others can add to to the device in their app. This code only
works for 5 minutes at a time.
1. To update position on the tracker, click the “update location” button found in the
map, or in the “devices” tab in the application. You can also update location by using
“live tracking”, which you can find in the menu in the bottom right corner in the map.
Enable it by clicking the button that looks like this ((.)). You can then choose update
interval, and when it’s activated the ((.)) symbol will turn red.
7. Update position
7
1. To make changes to your device or to add more people who can see the device,
simply click on the device, and you will find this menu.
8. General information
8
2. Inside the screen where you can change your device, you can rename it, change
image, see how much remaining battery there is on the tracker and you can see
which other users also have access to the tracker.
3. To update the main screen after updating your location, drag down the main screen.
Then you will see the latest update you made on your device. (Battery, last seen,
etc.)
4. To delete a device, drag the device to the left in the home screen. Then there is a
delete button, which you simply press and delete the device. If you are Admin using
the device, it will also be deleted from the others who have access to the device
when you delete it.
9
5. To enter the map to see where your device is located, tap the map icon on the device
under “devices” in the app and the map will appear. The blue little dot is your own
position on your mobile, and the device is the slightly larger location needle with a
picture in the middle.
Inhaltsverzeichnis
Andere Tail It GPS Handbücher
