Tamron B005 Bedienungsanleitung

SP AF 17-50mm F/2.8

XR Di-II VC LD Aspherical [IF]

(Model B005)

Thank you for purchasing the Tamron lens as the latest addition to your

photographic equipment. Before using your new lens, please read the

contents of this Owner’s Manual thoroughly to familiarize yourself with

your lens and the proper techniques for creating the highest quality

images possible. With proper handling and care, your Tamron lens will

give you many years of photographing beautiful and exciting pictures.

LOCK

IT]

Nikon

•8005NU: ThIs

modol;s

Built-In

Motor

1lOO6NI:

~.ot!~J6'l

Canon

[5]

AF:

·:i'lt~-~

-3:

[6] I

MF:

-0

--%

NOMENCLATURE

1. Lens hood

2. Hood attaching alignment mark

3. Hood attached indicator

4. Filter ring

5. Hood attaching bayonet ring

6. Focusing ring

7. Distance scale

8. Distance index

9. Zooming ring

10. Focal length scale

11. Zoom lock switch (Fig. 3 & 4)

12. VC (Vibration Compensation) switch

13. AF/MF switch (Fig. 5 & 6)

14. Zoom index mark

15. Lens attachment mark

16. Lens mount/Lens mount contacts

B005

Focal Length 17-50mm

Maximum Aperture F/2.8

Angle of View 78 45'-31 11'

Lens Construction 14/19

Minimum Focus Distance 0.29m

Maximum Magnification Ratio 1:4.78

Filter Size 72mm

Length 94.5mm

Diameter 79.6mm

Weight 570g

Hood AB003

SPECIFICATIONS

* Features and cosmetic designs of lenses listed in this owner's manual may be revised without notice.

ATTACHING AND REMOVING THE LENS

How to mount the lens

Remove the rear cap of the lens. Align the lens attachment mark on the lens barrel

with its counterpart on the camera mount and insert the lens.

In case of Nikon mount, rotate the lens counter-clockwise until it clicks into the locking

position. In case of Canon mount, rotate the lens clockwise until it clicks into the lock-

ing position.

How to detach the lens

Press the lens release button on the camera down.

In case of Nikon mount, rotate the lens clockwise until it unlocks from the camera.

In case of Canon mount, rotate the lens counter-clockwise until is unlocks from the camera.

*For further details, please read the instruction manual of your camera.

FOCUSING (Autofocus)

Switch the AF/MF switch on the lens to AF (Fig. 5). In case of Nikon camera with

the focus mode selector dial, set the focus mode to “S” or “C”, and then set the

AF/MF switch on the lens side to “AF”. Press the shutter button lightly while

viewing through the camera’s viewfinder. The lens focuses automatically.

An in-focus mark will light when lens focuses on the main subject sharply. Press the

shutter button further to photograph.

* When set on AF mode, interfering with the focusing ring may cause serious damage to the lens mechanism.

* The distance scale is marked for guidance purposes. The actual focal point may slightly differ from the distance marked

on the focal length index.

FOCUSING (Manual Focus)

Switch the AF/MF switch on the lens to MF (Fig. 6). In case of Nikon camera with the

focus mode selector dial, set the focus mode to “M”, and then set the AF/MF switch on

the lens side to “MF”. Focus manually by rotating the focusing ring while viewing

through the camera’s viewfinder. The main subject in the viewfinder will be sharp when

the lens id focused correctly.

* Even when in MF mode, turning the focusing ring while pressing the shutter button halfway, the focus aid function lamp

lights up when the picture is in focus.

* At infinity, make sure the image in the viewfinder appears sharp. The infinity position is made with certain allowances to

insure proper focus under a variety of conditions.

* For further details, please read the instruction manual of your camera.

VC MECHANISM

VC (Vibration Compensation) is a mechanism which reduces the image blur caused by

hand-held shooting. When using the VC, pictures can be taken at shutter speeds up to

a maximum of 4 stops slower than the speed when the VC is not used.

*Based on the company’s standard measurement. Also, the correction of image blur differs depending on the conditions

during picture taking and the person using the camera.

* How to use VC mechanism

VC can be used in AF or MF mode.

1. Set the VC switch on.

*When VC is not used, set switch off.

2. Press the shutter button halfway to verify the effect of the VC. When the shutter

button is pressed halfway, it takes about 1 second for the VC to provide a stable

image. With the VC mechanism, there are no occasions when the image in the

viewfinder blurs after the shutter button is pressed down halfway.

* The VC can be effective for hand-held shots under the following conditions:

-Dimly lit locations

-Scenes where flash photography is forbidden

-Situations where your footing is uncertain

-Taking continuous shots of moving subjects

* The VC may not be able to give full effect in the following cases:

-When a photograph is taken from a fast moving vehicle

-Shooting during the excessive movement of the camera

-Turn the VC switch OFF when taking pictures with the bulb setting or during long

exposures. If the VC switch is ON, the VC mechanism may introduce errors.

*Please refer to the “Caution when using B003” enclosed with your lens for the cautions for each mount.

-With the VC mechanism, there are occasions that the image in the viewfinder blurs right after the shutter

button is pressed down halfway, but this is not a malfunction.

-When the VC is ON, the number of images recordable is reduced due to the power used from the camera.

-When the VC is ON, immediately after the shutter button is pushed halfway down and approximately 2

seconds after a finger releases the shutter button, the camera will “click”. This sound is the VC’s locking

mechanism activating, not malfunctioning.

-Turn the VC switch OFF when using a tripod.

-After releasing the shutter button, the VC will continue to operate for about 2 seconds until the locking

mechanism activates.

-When the lens is removed from the camera while VC is activating, the lens may make clicking sound when the

lens is subjected to jolt. This is not a malfunction. Re-attach the lens to the camera and turn the power ON. The

sound should stop.

-The VC activates while the “release” button is pushed halfway down. (It is activated 2 seconds after the

shutter button is released.)

-VC can be used in AF or MF mode.

ZOOMING

Rotate zooming ring (9) of the lens while viewing through the camera’s viewfinder and

compose your image at the chosen focal length.

ZOOM LOCK SWITCH

Zoom lock switch mechanism prevents lens barrels from extending toward long focal

length by their own weight while hanging from shoulders. Activate the switch at 18mm

setting to stop the lens barrels from rotating and extending.

How to activate the zoom lock switch mechanism

1. Locking: Set the lens to the 18mm position. Move the switch (11) toward the camera,

until the index lines align with each other. The lens barrel is now locked in position and

does not rotate or extend by its own weight.

2. Releasing: Push the switch away from your camera. The lens barrel is now free to

rotate and extend for zooming.

-The zoom lock switch cannot be activated unless the lens is set to the 18mm position.

Do not force the lock switch or try to rotate the lens barrel when locked.

-The lens can be used at 18mm setting for picture-taking even when locked by the switch.

-The zoom lock mechanism is made to prevent the lens barrel from extending while

carried around on shoulder. The lens may change its focal length during a long

exposure if the lens is used in a low or high angle position.

LENS HOOD

A bayonet-type lens hood is provided as standard equipment. We recommend shooting

with the hood attached whenever possible as the lens hood eliminates stray light, which

is harmful to the picture. However, please be aware of the precautions stated in the next

section when your camera is equipped with a built in flash.

Attaching the Lens Hood

Align Hood attaching alignment mark (2) on the hood with the corresponding index mark

(5) or the top of the index line of the distance scale of the lens. Press the hood lightly.

The lens hood will be secure when the mark “TAMRON O” is at the top. When attaching the lens

hood, hold the focus and zoom control rings, so they are not rotated unintentionally.

-Pay particular attention to align the hood attaching indexes when using zoom lenses

including wide-angle setting. Improper attachment of a hood on a wide-angle zoom lens

may cause large shadowed areas in your pictures.

Stowing lens hood on the lens

Reverse the lens hood. Point the lens toward the opening, and then align the hood

attaching index on the lens with the “TAMRON O” alignment on the hood.

Turn the hood clockwise until the alignment mark is at the top to set it.

PRECAUTIONS IN SHOOTING

-The optical design for Di-II takes into consideration the various features of digital

single reflex cameras. However, due to the configuration of the digital single reflex

cameras, even when auto focus accuracy is within specifications, the focal point may

be a little forward or behind the optimum point when shooting with auto focus under

some conditions.

-The image circle of Di-II lenses are designed to match the digital SLR cameras using

the image sensors equivalent to APS-C (approx. 15.5x23.2mm). Do not use Di-II

lenses with cameras using image sensors larger than APS-C. Using Di-II lenses with

such cameras may cause vignetting on the image.

-The Tamron lenses described here emply an internal focusing (IF) system. Because of

the characteristics of this optical design, the angles of view at distances other than

infinity are wider than that of the lenses applying an ordinary focusing system.

-When the built-in-flash on the camera is used, adverse photographic phenomena such

as corner illumination fall-off or vignetting at the bottom part of the image may be

observed, especially in wide angle ranges. This is due to the inherent limitation of the

coverage of the built-in-flash, and/or the relative position of the flash to the edge of the

lens barrel which causes shadows on the image. It is strongly recommended to use a

suitable separate flash unit provided by the camera manufacturer for all flash p

hotography. For further details, please read the “built-in-flash” article on the instruction

manual of your camera.

-When using the lens in the telephoto focal range, please be careful of camera shake.

To reduce blur, turn the VC (Vibration Compensation) switch on. To reduce image blue

without using the VC function, follow these steps.

To avoid camera shake on digital cameras, use higher ISO settings and for film

cameras, use higher ISO film to obtain higher shutter speeds. Using a tripod or

monopod is also effective.

When hand-holding the camera to take pictures, stand still opening your legs slightly

apart, hold your elbows in firmly against your chest, and hold the camera firmly

against your face. If possible, lean against something to steady yourself or place the

camera on something to secure the hold. Especially when hand-holding your camera,

you will be steadier if you hold your breath while your press the shutter button down

gently and firmly.

-When set on AF mode, interfering with the focusing ring may cause serious damage to

the lens mechanism.

Certain models may indicate the maximum and minimum aperture values of the lens in

approximate numbers. This is inherent to the design of the camera and not an

indication of an error.

-Please be aware that there is no infrared index line on any models listed in this owner’s

manual, and therefore, practically no black-and-white infrared file can be used with

these lenses.

-When using a special filter such as a PL filters, use low profile filters. The thick rim of

a normal filter may cause vignetting.

TO ENSURE LONG-TERM SATISFACTION

-Avoid touching the glass element surface. Use photographic lens cloths or blowers to

remove dust from the lens element surface. When not using the lens, always place a

lens cap on it for protection.

-Use a lens cleaning tissue or lint cloth with a drop of cleaning solution to remove

fingerprints or dirt on the glass lens surface with a rotary motion from the center to the

edge. Use a silicone cloth to clean your lens barrel only.

-Mildew is an enemy of your lens. Clean the lens after shooting near water or in any

humid place. Store your lens in a clean, cool, dry place. When storing the lens in a lens

case, store it with commercially available drying agents such as silicagel, and change

the agent occasionally. If you find mildew on your lens, consult an authorized repair

shop or nearby photographic store.

-Do not touch the lens-camera interface contacts since dust, dirt and/or stains may

cause a contact failure between the lens and camera.

-When using your equipment [camera(s) and lens(es)] in an environment where the

temperature changes from one extreme to the other, make sure to put your equipment

temporarily in a case or plastic bag for a length of time in order for the equipment to go

through a gradual temperature shift. This will reduce potential equipment trouble.

TLM-EFDSINPC-B005NE-U-0907

TAmROn

•

AF17-S0mm F/2.8

Dill

Aspherical [IF] (Model

BOOS)

Nikon

BOO5NI:

This model is

BuHt·in

MotOf

BOO5NI:

PiIlrt!i;!JrJ.

Canon

[5] I

AF:

ON I

[E]

IMF: ON I

[Z]

IVC: ON I

[B]

IVC: OFF I

t~~

'.J~~

~,~:;

--.z

.201

,-lJ---=·~

-"J::

--"

"T'I

f------)-

C€

•The

(€

Marking

adirective conformity mark of the European Community (ECl.

•Das (€-Zeichen entspricht der EC Norm.

•

marquage

(€

est un marquage de conformite

ilia

direcive CEE (CEl·

•La marca

((

es marca de conformidad segun directiva de la Comunidad Europea (CE),

•

marchio

(€

attesla la conformita alia directtiva della Comunitil Europea (CEE).

•

(€

j;j;;I;.J'<iF"'M.xHH\ii'lU'<EClltifir.

The EEC Conformity Report applies to the

E:counciIDirective98/336/EEC,92/31/EEC.

93/68/EEC and

used by Tamron Co., Ltd.,

manufacturer of this product.

ENGLISH

! .

1l'

values

are

specifICations

Nikon

products.

Features

and

appearance

lenses

listed

this owner's

manual

are

subject to

change

without

notice.

•Stowing lens hood

the lens

(Ref.

Fig,

IIJI)

Reverse

the

lens

hood.

Point

the

lens

toward

the

opening,

then

align

the

hood

attaching

index

the

lens

with

the

(TAM

RON

alignment

ttle

hood

Turn

the

hood

clockwise

until

the

alignment

mark

(.)

the top

set

it.

(Fig.

IIJI)

PR~UTIONS

SHOOTINif

•

The

optical

design

for

takes

into

consideration

the

various

features

digital

single

reflex

cameras.

However,

due

the

configuration

the

digital

single

reflex

cameras,

even

when

the

autofocus

accuracy

within

specifications,

the

focal

point

may

little

forward

behind

the

optimum

point

when

shooting

wrth

auto

focus

under

some

conditions.

•

The

image

circles

lenses

are

designed

match

ttle

digital

SLR

cameras

using

the

image

sensors

equivalent

APS-C

(approx.

15.5

23.2mm).

not

use

lenses

with

cameras

using

image

sensors

larger

than

APS-C.

Using

lenses

with

such

cameras

may

cause

vignetting

the

image.

•

The

Tamron

lenses

described

here

employ

internal

focusing

(IF)

system.

Because

the

characteristics

this

optical

design,

the

angles

view

distances

other

ttlan

infinity

are

wider

than

that

the

lenses

applying

ordinary

focusing

system.

•

When

the

built-in

flash

the

camera

used,

adverse

photographic

phenomena

such

corner

illumination

fall-off

vignetting

the

bottom

part

the

image

may

observed,

especially

wide

angle

ranges.

This

due

the

inherent

limitation

the

coverage

the

built-in

flash,

and/or

the

relative

position

the

flash

the

edge

the

lens

barrel

which

causes

shadows

the

image.

strongly

recommended

use

suitable

separate

flash

unit

prOVided

the

camera

manufacturer

for

all

flash

photography.

For

further

details,

please

read

the

"buirt-in

ftash"

article

the

instruction

manual

your

camera.

•

When

using

the

lens

the

telephoto

focal

range,

please

careful

camera

shake.

reduce

image

blur,

turn

the

(Vibration

Compensation)

switch

on.

reduce

image

blur

without

using

the

function,

the

steps

below.

avoid

camera

shake

digital

cameras,

use

higher

ISO

setting

and

for

film

cameras,

use

higher

ISO

film

obtain

higher

shutter

speeds.

Using

tripod

monopod

also

effective.

When

hand-holding

the

camera

take

pictures,

stand

still

opening

your

legs

slightly

apart,

hold

your

elbows

firmly

against

your

chest,

and

hold

the

camera

firmly

against

your

face.

possible,

lean

against

something

steady

yourself

place

the

camera

something

secure

the

hold.

Especially

when

hand-holding

your

camera,

you

will

steadier

you

hold

your

breath

while

you

press

the

shutter

button

gently

and

tirmly.

•

When

set

mode,

intertering

wittl

focusing

ring

may

cause

serious

damage

the

lens

mechanism.

•

Certain

camera

models

may

indicate

the

maximum

and

minimum

aperture

values

the

lens

approximate

numbers.

This

inherent

ttle

design

the

camera

and

not

indication

error.

•

Piease

aware

that

there

infrared

index

line

any

models

listed

this

owner's

manual,

and

therefore,

practically,

black-and-

white

infrared

film

can

used

with

these

lenses.

•

When

using

special

filter

such

filter,

use

low

profile

filters.

The

thick

rim

normal

filter

may

cause

vignetting.

UQjI!i!!BH08.G~SljwAm!·!!I'_

l-21-A_...-.-

...........

~iIlII

•

Avoid

touching

the

glass

element

surface.

Use

photographic

lens

cloth

blower

remove

dust

from

the

lens

element

surface.

When

not

using

the

lens,

always

place

lens

cap

for

protection.

•

Use

lens

cleaning

tissue

lint

clottl

with

drop

cleaning

solution

remove

fingerprints

dirt

the

glass

lens

surface

with

rotary

motion

from

the

center

ttle

edge.

•

Use

silicon

cloth

clean

your

lens

barrel

only.

•

Mildew

enemy

your

lens.

Clean

ttle

lens

after

shooting

near

water

any

humid

place.

Store

your

lens

clean,

cool

and

dry

place

When

storing

the

lens

case,

store

with

commercially

available

drying

agent

such

silicagel,

and

change

the

agent

occasionally.

you

find

mildew

your

lens,

consult

authorized

repair

shop

nearby

photographic

store.

•

not

touch

the

lens-camera

interface

contacts

since

dust,

dirt

and/or

stains

may

cause

contact

failure

befween

ttle

lens

and

camera.

•

When

using

your

equipment

[camera(s)

and

lens(es)]

environment

where

the

temperature

changes

from

one

extreme

ttle

ottler,

make

sure

put

your

equipment

temporarily

case

plastic

bag

for

length

time

order

for

the

equipment

through

gradual

temperature

shift.

This

will

reduce

potential

equipment

trouble.

•

With

the

mechanism,

there

are

occasions

that

the

image

the

viewfinder

blurs

right

after

the

shutter button is

pressed

down

halfway,

but

this is

not

amalfunction.

•

When

the

ON,

the

number

images

recordable

reduced

due

the

power

used

from

the

camera.

•

When

the

ON,

immediately after

the

shutter button is

pushed

halfway

down

and

approximately 2

seconds

after afinger

releases

the

shutter button, the

camera

will

"click".

This

sound

the

VC's

locking

mechanism

activating, not amalfunction.

•

Tum

the

swtich

OFF

when

using

tripod.

•After releasing

the

shutter button, the

will continue to

operate

for about 2

seconds

until the locking mechanism activates.

••

•

The

zoom

lock switch ®

cannot

activated

unless

the

lens

set

the

17mm

..,

position.

not

force

the

lock switch

try

rotate

the

lens

barrel

while

locked.

•

The

lens

can

used

17mm

setting for picture-taking

even

when

locked

the

switch.

•

The

zoom

lock

mechanism

made

prevent

the

lens

barrel

from

extending

while

carried

around

shoulder.

The

lens

may

change

its

focal

length

during a

long

exposure

the

lens

used

low

high

angle

position.

~Q]Rei.

Fjg.blJ1;~

IDJ)I=~=::Jr:::::::::::::::::.

bayonet-type

lens

hood

provided

standard

equipment.

recommend

shooting

with

the

hood

attached

whenever

possible

ttle

lens

hood

eliminates

stray

light,

which

harmful

ttle

picture.

However,

please

aware

ttle

precautions

stated

the

section

when

your

camera

equipped

with

built-in

flash.

•Attaching the

Lens

Hood

(Ref.

Figs.

I9J

IIDI)

Align

Hood

attaching

alignment

mark

121

the

hood

wrth

the

corresponding

index

mark

the top

fhe

index

line

the

distance

scale

the

lens.

Press

the

hood

lightly

onto

ttle

hood

attaching

bayonet

ring

(Fig.

1!lJ)

and

ttlen

rotate

clockwise

secure

(Fig.

1!lJ).

The

lens

hood

will

secure

when

the

mark

"TAlVRON

the top

(Fig.IIDI).

When

attaching

the

lens

hood,

hold

ttle

focus

and

zoom

control

rings

that

they

are

not

rotated

unintentionally.

I .

Pay

particular attention

align

the

hood

attaching

indexes

when

using

zoom

lenses

including wide-angle

(e.i.

35mm

wider)

settings.

Improper

attachment of a

hood

wide-angle

zoom

lens

may

cause

large

shadowed

areas

your

pictures.

~IEIWj!l~l(liif:

!'IO.

.•

tlI

lSI)'

(Vibration

Compensation)

mechanism

which

reduces

the

image

blur

caused

hand-held

shooting.

When

using

ttle

VC,

pictures

can

taken

shutter

speeds

maximum

stops

slower

than

the

speed

when

the

not

used.

*Based

ttle

company's

standard

measurement.

Also,

the

correction

image

blur

differs

depending

the

conditions

during

picture

taking

and

the

person

using

the

camera.

•

How

use

mechanism

can

used

mode.

Set

ttle

VC@switchon.

'When

not

used,

set

the

switch

off.

Press

ttle

shutler

button

halfway

verify

ttle

effect

the

VC.

When

the

shutter

button

pressed

down

halfway,

takes

about

second

for

the

provide

stable

image.

With

the

mechanism,

there

are

occasions

when

the

image

the

viewfinder

blurs

after

the

shutter

button

pressed

down

halfway.

•

The

can

e"ective for hand-held shots under the following

conditions.

•

Dimly

lit

iocations

•

SCenes

where

flash

photography

forbidden

•

Situations

where

your

footing

uncertain

•

Taking

continuous

shots

moving

subjects

•

The

may

not

able to give full

e"ect

the following

caSeS:

•

When

photograph

taken

from

fast

movimg

vehicle

•

Shooting

during

the

excessive

movement

the

camera

•

Tum

the

switch

OFF

when

taking

pictures

wittl

the

bulb

setting

during

long

exposures.

the

switch

ON,

the

mechanism

may

introduce

errors.

! .

The

17-50mm

F/2.8

(model

BOOS)

lens

hood

also

used

for

the

18-

270mm

F/3.5-6.3

(model

8003).

Described

"AB003"

the

lens

hood

When

the

tens

removed

from

the

camera

while

activating,

the

lens

may

make

clicking

sound

when

the

lens

subjected

jolt.

This

not

malfunction.

Re-attach

the

lens

the

camera

and

turn

the

power

ON.

The

sound

should

stop.

•

The

activates

while

the

"release"

button

pushed

halfway

down.

(It

activated

seconds

after

the

shutter

button

released)

•

can

used

mode.

~:tOOlmjjU!W.l'Ia:L-~~·'''IIl''''_'''"!"''---'''~~,,,,!''!··::iIli.''''·

~'

Rotate

zooming

ring

the

lens

while

viewing

through

the

camera's

viewfinder

and

compose

your

image

the

chosen

focal

length.

ff~\'ml;Jt~(M

cl3l

m)'t1

\\'m"!l!t'

Zoom

lock

switch

mechanism

prevents

lens

barrels

from

extending

toward

long

focal

length

their

own

weight

while

hanging

from

shoulders.

Activate

the

switch

17mm

setting

stop

the

lens

barrels

from

rotating

and

extending.

•

How

to activate the

zoom

lock switch mechanism

Locking:

Set

the

lens

ttle

17mm

position.

Move

the

switch

@towardthecamera,

until

the

index

lines

align

with

each

other.

The

lens

barrel

now

locked

position

and

does

not

rotate

extend

its

own

weight.

Releasing:

Push

the

swrtch

away

from

your

camera.

The

lens

barrel

now

free

rotate

and

extend

for

zooming.

B005

AB003

F/2.8

1:4.78

14/19

72mm

17-50mm

0.29m(11.4")

79.6

(3.1

570f(20.10zl

94.5mm"

(3.7")

Maximum

Magnification

Ratio

Minimum

Focusing

Distance

Length

Diameter~

Maximum

Aperture

Filter

Size

Lens

Construction

Angle

View

Weight

Lens

Hood

NOM~CEA.TUR.t

(R~:'o

F!lI.Ltl.

"Ill!t

Lens

hood

121

Hood

attaching

alignment

mark

Hood

attaching

indicator

Filter

ring

Hood

attaching

bayonet

ring

Focusing

ring

(l)

Oistance

scale

Oistance

index

Zooming

ring

®i

Focal

length

scale

Zoom

lock

switch

(Figs.

131

I'IJ)

(Vibration

Compensation)

switch

©i

AF/MF

switch

(Fig.

151

15l)

Zoom

index

mark

Lens

attachment

mark

Lens

mounVLens

mount

contacts

~~ilt

The

17-50mm

F/2.8

(model

BOOS)

lens

hood

also

used

for

the

18-270mm

F/3.5-6.3

(model

6003).

rmA~1lNiiii8iMM

•

How

to mount the lens

Removing

the

rear

cap

the

lens.

Align

the

Lens

attachment

mark

(@)

the

lens

barrel

with

its

counterpart

the

camera

mount

and

insert

the

lens.

Rotate

the

lens

clockwise

until

click-locks.

For

Nikon

models,

align

the

lens

attachment

mark

with

the

dot

the

camera

and

rotate

the

lens

counter-clockwise

until

click-locks.

•

How

to detach the lens

Pressing

the

lens

release

button

the

camera

down,

turn

the

lens

counter-clockwise

(in

case

Nikon

lens,

clockwise),

and

lift

the

lens

off

the

camera's

lens

mount.

For

further

details,

please

read

the

instruction

manual

your

camera.

-roCUSltfG

(AUtOfcjJl!!!!).:mif~"'l:,

....

------

Switch

the

AF/MF

switch

©i

the

iens

(Fig.

151).

case

Nikon

camera

with

the

focus

mode

selector

dial,

set

the

focus

mode

"S"

"C",

and

then

set

the

AF/MF

switch

the

lens

side

©i

"AF".

Press

the

shutter

button

lightly

while

viewing

through

the

camera's

viewfinder.

The

lens

focuses

automatically.

in-focus

mark

will

light

when

lens

focuses

the

main

SUbject

sharply.

Press

the

shutter

button

further

photograph.

I .

When

set

mode.

interfering with

focusing

ring @

may

cause

serious

damage

the

lens

mechanism.

•

The

distance

scale

(J)

marked

for

guidance

purposes.

The

actual

focal

point

may

slighUy

differ

from

the

distance

marked

the

focal

length

index.

For

further

details,

please

read

the

instruction

manual

your

camera.

~~tlijmii~11l:'J2l:i:rjlll

...

Switch

the

AF/MF

switch

©i

the

lens

(Fig.Illi).

case

Nikon

camera

with

the

focus

mode

selector

dial,

set

the

focus

mode

"M",

and

then

set

the

AF/MF

switch

the

lens

side

"MF".

Focus

manually

rotating

the

focusing

ring

while

viewing

through

the

camera's

viewfinder.

The

main

SUbject

the

viewfinder

will

sharp

when

the lens

focused correctly.

Even

the

mode.

when

turning

focusing

ring

while

pressing

the

shutter

button

halfway.

the

focus

aid

function

lamp

lights

when

the

picture

focus.

•

infinity,

make

sure

the

image

the

viewfinder

appears

sharp.

The

infinity

position

made

with

certain

allowances

insure

proper

focus

under

variety

conditions

•

For

further

details,

please

read

the

instruction

manual

your

camera

Thank

you

for

purchasing

the

Tamron

lens

the

latest

addition

your

photographic

equipment.

Before

using

your

new

lens,

please

read

the

contents

this

Owner's

Manual

thoroughly

familiarize

yourself

with

your

lens

and

the

proper

techniques

for

creating

the

highest

quality

images

possible.

With

proper

handling

and

care,

your

Tamron

lens

will

give

you

many

years

photographing

beautiful

and

exciting

pictures.

I .

Explains

precautions that

help

prevent

problems.

Explains

things

you

should

know

addition

basic

operations.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tamron Kameraobjektiv Handbücher

Tamron

Tamron B060 Bedienungsanleitung

Tamron

Tamron 06B Bedienungsanleitung

Tamron

Tamron A062 Bedienungsanleitung

Tamron

Tamron A025 Bedienungsanleitung

Tamron

Tamron A041 Bedienungsanleitung

Tamron

Tamron BO11 Bedienungsanleitung

Tamron

Tamron SPECIFICATIONS Bedienungsanleitung

Tamron

Tamron A014 Bedienungsanleitung

Tamron

Tamron A13 Bedienungsanleitung

Tamron

Tamron 176A Bedienungsanleitung

Tamron

Tamron A037 Bedienungsanleitung

Tamron

Tamron F017 Bedienungsanleitung

Tamron

Tamron AF 18-200mm F/3.5-6.3 XR Di II LD Aspherical Bedienungsanleitung

Tamron

Tamron A03 Bedienungsanleitung

Tamron

Tamron A09 Bedienungsanleitung

Tamron

Tamron SP AF10-24mm F/3.5-4.5 Di II LD Aspherical (IF)... Bedienungsanleitung

Tamron

Tamron 360EE Bedienungsanleitung

Tamron

Tamron 17-50mm F/4 Di III VXD Bedienungsanleitung

Tamron

Tamron SP 70-210mm F/3.5 19AH Bedienungsanleitung

Tamron

Tamron F004 Bedienungsanleitung

Tamron

Tamron SP85mm F/1.8 Di VC USD Bedienungsanleitung

Tamron

Tamron SP24-70mm F/2.8 Di VC USD Bedienungsanleitung

Tamron

Tamron B011 Bedienungsanleitung

Tamron

Tamron SPAF17-50mm F/2.8 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Bedienungsanleitung

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Bedienungsanleitung

Rokinon

Rokinon DS50M-C Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung